CUB A009-007 77GHz TA BSD Radar Module User Manual
- June 16, 2024
- Cub
Table of Contents
CUB A009-007 77GHz TA BSD Radar Module User Manual
GENERAL SPECIFICATIONS
| Item | Parameters | Value |
|---|---|---|
| 1 | Operation voltage | 9 — 36 V |
| 2 | Operation frequency | 76-77 GHz |
| 3 | Occupied Bandwidth | 400 MHz |
| 4 | EIRP | 27dBm |
| 5 | ADC sampling rate | 20 MSPS |
| 6 | MCU RAM SIZE | 768 kB |
| 7 | MCU flash size | 1 MB |
| 9 | Power consumption | < 220mA @ 13.5V < 110mA @ 27V |
| 10 | Update rate (Frame rate) | 20Hz |
| 11 | longitudinal | |
| Detection range | Lateral | 0.5-45m |
| 12 | Detection range | Accuracy |
| Resolution | 1.5m | |
| 13 | longitudinal | |
| Velocity range | Lateral | ±20m/s |
| 14 | Velocity range | Accuracy |
| Resolution | 1 m/s | |
| 15 | FOV | Horizontal |
| Vertical | ±6° | |
| 16 | Angle accuracy | ±0.25 deg |
| 17 | Angle resolution | ±20° |
REGULATORY STATEMENTS
FCC Statement
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located with any other
transmitters except in accordance with FCC multi-transmitter product
procedures.
Referring to the multi-transmitter policy, multiple-transmitter(s) and
module(s) can be operated simultaneously without C2PC.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
IMPORTANT NOTE:
This module is intended for OEM integrator only and limited to host with
brand: Cub and model: B122-009NA1-A2, B122-009NA1-A3, B122-010NA1-A2,
B122-010NA1-A3, B122-073NA1-A0, B122-072NA1-A0, B122-075NA1-A0,
B122-074NA1-A0. This module is only FCC authorized for the specific rule parts
listed on the grant, and that the host product manufacturer is responsible for
compliance to any other FCC rules that apply to the host not
covered by the modular transmitter grant of certification. The final host
product still requires Part 15 Subpart B compliance testing with the modular
transmitter installed.
USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio- frequency exposure guidelines for an uncontrolled environment can be satisfied.
The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
The FCC part 15.19 statement below has to also be available in the manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following” Contains TX FCC ID: ZPNUNIVERSALTABSD”.
Ant. List
Ant.| Brand| Model Name| Antenna Type| Connector|
Gain (dBi)| Remark
---|---|---|---|---|---|---
1| Cub| CUBT76500| array| N/A| 11.71| TX
2| 13.9| RX
IC ISED STATEMENT:
THIS DEVICE CONTAINS LICENCE-EXEMPT TRANSMITTER(S) THAT COMPLY WITH INNOVATION, SCIENCE AND ECONOMIC DEVELOPMENT CANADA’S LICENCE-EXEMPT RSS(S). OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE INTERFERENCE,
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION OF THE DEVICE.
L’APPAREIL NE DOIT PAS PRODUIRE DE BROUILLAGE;
- L’APPAREIL DOIT ACCEPTER TOUT BROUILLAGE RADIOÉLECTRIQUE SUBI, MÊME SI LE BROUILLAGE EST SUSCEPTIBLE D’EN COMPROMETTRE LE FONCTIONNEMENT.
IMPORTANT NOTE:
IC RADIATION EXPOSURE STATEMENT:
THIS EQUIPMENT COMPLIES WITH IC RSS-102 RADIATION EXPOSURE LIMITS SET FORTH
FOR AN UNCONTROLLED ENVIRONMENT. THIS EQUIPMENTSHOULD
BE INSTALLED AND OPERATED WITH MINIMUM DISTANCE 20CM BETWEEN THE RADIATOR & YOUR BODY. CET ÉQUIPEMENT EST CONFORME AUX LIMITES D’EXPOSITION AUX RAYONNEMENTS IC ÉTABLIES POUR UN ENVIRONNEMENT NON CONTRÔLÉ. CET ÉQUIPEMENT DOIT ÊTRE INSTALLÉ ET UTILISÉ AVEC UN MINIMUM DE 20 CM DE DISTANCE ENTRE LA SOURCE DE RAYONNEMENT ET VOTRE CORPS.
This module is intended for OEM integrator only and limited to host with
brand: Cub and model: B122-009NA1-A2, B122-009NA1-A3, B122-010NA1-A2,
B122-010NA1-A3, B122-073NA1-A0, B122-072NA1-A0, B122-075NA1-A0,
B122-074NA1-A0. The OEM integrator is still responsible for the IC compliance
requirement of the end product, which integrates this module.
Any changes or modifications not expressly approved by the manufacturer could
void the user’s authority to operate this equipment.
USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the IC radio- frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment. Operation is subject to the following two conditions: (1) this device may not cause harmful interference (2) this device must accept any interference received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following” Contains IC: 9959A-VEC20BA20DA”. The Host Model Number (HMN) must be indicated at any location on the exterior of the end product or product packaging or product literature which shall be available with the end product or
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>