IRIS PCF-HD15NU WOOZOO Circulator Fan Instructions
- June 16, 2024
- IRIS
Table of Contents
WOOZOO® Circulator Fan by IRIS USA, Inc.
Series PCF-HD15NU I PCF-HD18NU
Thank you for your purchase. Please read this instruction manual carefully to
ensure proper use. Read all safety precautions prior to use. Please store this
instruction manual in a safe place for future reference.
READ AND SAVE THESE INSTRUCTIONS
SAFETY PRECAUTIONS
Prior to use, please read the safety precautions carefully to ensure proper
use. The precautions listed here are described under classification of
Warnings and Cautions, and are intended to prevent harm or damages to users
and other persons. All of these precautions are critical in terms of safety.
Please follow them at all times.
Graphic Symbol Indications: Indicates content that could lead to death or
injury if handled incorrectly.
CAUTION
PROHIBITED
INSTRUCTIONS THAT MUST BE FOLLOWED
Disassembly prohibited.
- Do not disassemble, repair, or modify. Doing so can cause fire, electric shock, or njury.
- Repair by persons other than trained repair technicians can be dangerous.
- Warning: To reduce the risk of fire or electric shock, do not use this product with any solid-state speed control device.
Product use.
- Use on a level, stable surface. Placing product on uneven and unstable surfaces can cause the product to fall over, leading to injury or damage to property in the vicinity of the product.
- Place the product in ocations where it will not get entangled in curtains or hoisting strings, etc. Failing to do so can cause damage to articles near the product.
- Always grasp the power plug to unplug it, do not unplug it by pulling on the power cord. Pulling on the power cord can damage it, which can cause fire or electric shock.
- Always unplug the power plug from the electric socket when the product will be unused for extended periods of time. Failing to do so can lead to fire or electric shock caused by short-circuits due to reduced insulation.
- This product employs overload protection (fuse). A blown fuse indicates an overload or a short-circuit. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit occurred and the product should be discarded or returned to IRIS USA, Inc. for inspection and/or repair.
Unplug.
-
Unplug the power plug from the electric socket when performing maintenance, inspecting, or moving the product.
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit n a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature. -
Grasp the plug and remove from the receptacle or other outlet device. Do not unplug by pulling on the cord.
Use power plugs and power cords correctly.
- Failing to do so can cause fire or electric shock due to short-circuits.
- Insert the power plug securely all the way into the electric socket.
- Regularly remove dust from the power plug.
- When dust is allowed to build up, insulation s hampered due to moisture, which can cause fire or electric shock.
- Use only 120V AC. Other current/voltage can cause fires.
- Do not use if the power cord or the power plug is damaged, or if the power plug is loose when plugged into the electric socket. Doing so can cause fire or electric shock due to short-circuit.
- Do not run the cord under carpeting. Do not cover the cord with throw rugs, runners, or similar coverings. Do not run the cord under furniture or appliances. Arrange the cord away from high traffic areas and where it will not be tripped over.
- Do not operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair.
Do not damage the power cord.
- Damaging, modifying, forcefully bending, pulling, twisting, putting heavy objects, or pinching can damage the power cord, which can cause fire or electric shock.
- Do not use if the power cord is bundled up. Doing so can cause fires. Always extend the cord out before using.
- Do not pull on the power cord when carrying or storing the product. Pulling on the power cord can cause fire or electric shock.
Abnormalities and malfunctions can cause smoke, fire, or electric shock.
Stop use immediately, cut power, and unplug from the electric socket when
abnormalities or malfunctions occur.
Examples of Abnormalities
- Abnormal sounds or odors.
- Power plug or power cord become abnormally hot.
- Loss of power, etc. when power cord is moved.
- The product periodically stops during operation.
- Tingling sensation from electric current felt when the product is touched.
- Stop use and contact IRIS USA, Inc. customer service at 1-800-320-474.
Avoid fire hazards.
- Do not spray with nsecticides, hair sprays, or lubrication oils, etc.
- Do not use near flammable substances (kerosene, gasoline, paint thinner, etc.), objects that have flames (cigarettes, incense, etc.) or combustible materials. Can cause fires.
- Do not use the product with air flow pointed at a combustible appliance such as a heater. Doing so can cause incomplete combustion or scatter flames, which can cause carbon monoxide poisoning and fire.
Wet hands prohibited.
- Do not unplug power plug when hands are wet.
Do not use the product outdoors.
- Do not use in the vicinity of objects that obstruct the flow of air.
- Do not operate while covered or blocked with cloth, paper, or plastic bags, etc.
- Do not use in locations where there is a lot of dirt or dust. This can cause short-circuit or fire.
- Do not use in rooms with high humidity levels such as bathrooms.
- Do not get the unit wet, or put the unit in water. Getting the product wet can cause fire or electric shock.
If handled incorrectly, contents can lead to personal injury or physical damage.
- Keep out of reach of children and infants.
- Do not climb on or tip the product over. Doing so may lead to injury or electric shock.
- Do not drag the product when moving it. Dragging product can damage carpet and floors.
- Do not point air flow directly at your body. It generates a very strong air flow.
- Be especially mindful not to allow children or elderly people near product. Being near the product can be harmful to their physical condition and to their health.
- Air blowing directly on plants may be harmful.
- Do not operate without attaching the vane or the cover. Doing so can cause injury, electric shock, or fire.
- Do not strike the unit forcefully. Doing so can cause the product to malfunction, leading to fire or electric shock.
User Servicing Instructions
- If the fuse on your fan has blown, grasp the plug and remove it from the outlet. Do not pull the cord to unplug.
- To open, slide the fuse cover towards the prongs of the plug.
- Carefully remove the old fuse and snap the replacement fuse into place. To reduce the risk of fire, only replace the fuse with another fuse of the proper rating (2.5Amp, 125Volt). Slide the fuse door back into place to close. Discard the blown fuse. The plug should now be ready for normal use.
- To reduce the risk of fire, do not replace the attachment plug if it s damaged. Only the fuse should be replaced. Discard the product if the attached plug is damaged.
- If you need further information on how or when to replace the fuse in plug, please contact IRIS USA, Inc. customer service at 1-800-320-4747.
PLACEMENT
Placement
Place the product on a level floor or table free of any obstructions.
- Place the product in locations where it will not come in contact with direct sunlight, or hot air from air conditioning or heating appliances. Such contact can cause the product to deform, change color, or malfunction.
- Do not place the product near the radio or TV. The product may cause noise on radio and affect the TV signal.
Use with Air Conditioner
Placing the product n front of air conditioner to circulate cold air
accumulated below creates air flow and provides better cooling.| Use with a
Heater
Sending air flow to corner of the room where the A/C source is, to circulate
warm air accumulated above, warms feet.| Circulation
Sending air flow toward the ceiling reduces room air temperature variations.
Ventilation
Placing the product by a widow or a door draws outside air in and sends in-
room air out.| Two-room Circulation
Placing the product n an open doorway circulates air between
two-rooms.| Drying Laundry
Hanging laundry directly in the path of the air flow helps t dry quicker.
Do not place underneath dripping clothes as water droplets on the product may
cause electric shock or short-circuiting.
Parts
Control Panel *Demonstrated model is PCF-HD15NU
HOW TO USE
Place the Product
Place the product upright on a stable surface and insert the power plug into
the electrical outlet.
Select the Preferred Air Flow Strength
Turning the knob selects the desired air flow strength. Stop the
Product
Turn the knob to OFF to stop the operation.
Adjusting Angle
Vertical
- Vertical angle can be adjusted manually across 6 steps from approximately -20 to 90 degrees.
Storage
If product is not in use for extended periods of time, cover the product and
store in places with low humidity and no direct sunlight.
CLEANING AND MAINTENANCE
CAUTION
Always turn off the power and unplug the power plug from the electric
socket when cleaning the product. Use caution, the motor will be hot
immediately after use. Confirm the motor has cooled before cleaning the
product.
Do not use paint thinner, alcohol, benzene, alkaline detergent, or bleach,
etc. when cleaning the product. Using such substances can cause damage,
malfunctions, or changes in color, shape, and quality.
Using the product in dusty condition can cause it to malfunction. Check and
clean the product regularly.
Internal Cleaning
- Unscrew the screws from the back cover of the fan. Press in and disengage the 4 claws on the top and bottom of the front guard, and then remove the front guard by pulling it toward you.
- Remove debris using a vacuum cleaner. Wipe off debris that cannot be removed by vacuuming using a soft cloth.
- Align claws on the top and bottom of the front guard with the guides on the back of the guard, align the handle on the back with the groove on the top of the front guard, and press until it snaps into place.
External Cleaning
- Wipe lightly using a soft cloth.
- For hard to remove dirt, wipe using a cloth containing a diluted neutral detergent.
TROUBLESHOOTING
Before making repairs, please read the following content carefully to fix common problems.
STATUS | POSSIBLE CAUSE | REMEDY |
---|---|---|
Will not operate | The power plug may not be properly inserted in the electric | |
socket, | Insert the power plug securely into the electric socket. | |
Weak air flow | Dust may have accumulated. | Clean the product to remove dust. |
Product makes loud noise
while operating| The product is placed on an uneven surface.| Place the
product on a level, stable surface.
The front guard is not securely attached.| Attach the front guard properly.
Problems that could not be resolved.
Please contact the dealer of purchase or IRIS USA, Inc. Customer Service.
Warning: Do not disassemble, repair or modify the product yourself. Any
other servicing should be performed by any authorized service representative.
Product Used Over Long Periods of Time
If any of the following problems occur due to use over long periods of time,
cut power immediately, unplug from the electric socket, and contact IRIS USA,
Inc. customer service at
1-800-320-4747.
- There is no response when power switch is pressed.
- Product makes a strange noise when operating.
- While turning, the vane changes speed irregularly.
- Power cord is bent or damaged.
- Power turns on and off when power cord is touched.
- Product gives off a burnt smell.
WARNING
Various factors can have an impact on the product degradation and
malfunction.
If abnormalities like those listed above occur even when the product has not
been used for the displayed standard period of use, stop use immediately and
contact IRIS USA, Inc. customer service at
1-800-320-4747.
SPECIFICATIONS
MODEL | SPECIFICATIONS |
---|---|
RATED VOLTAGE | 120VAC |
RATED CURRENT | PCF-HD15NU |
PCF-HD18NU | 0.6A |
RATED FREQUENCY | 60Hz |
PRODUCT SIZE
(NOT INCLUDING THE POWER CORD)| PCF-HD15NU| 9.49 x 6.89 x 10.47 in / 241 x 175
x 266 mm
PCF-HD18NU| 11.42 x 7.48 x 11.42 in / 290 x 190 x 290 mm
PRODUCT WEIGHT| PCF-HD15NU| 3.09 lbs / 1.4 kg
PCF-HD18NU| 3.75 lbs / 1.7 kg
APPLICABLE AREA COVERAGE| PCF-HD15NU| 157 ft2 / 14.6 m2
PCF-HD18NU| 275 ft2 / 25.5 m2
POWER CORD LENGTH| About 70.9 in / 1.8 m
*Specifications are subject to change without prior notice.
MANUFACTURER 1-YEAR WARRANTY
THE MANUFACTURER WARRANTS
Your IRIS USA, Inc. products are to be free from defects in material and
workmanship under normal non-commercial, household use, when operated and
cared for in accordance with the Manufacturer’s written instructions provided.
THE 1-YEAR WARRANTY (“WARRANTY”) DOES NOT COVER
Any damage caused by accident, misuse, or abuse, including without limitation,
damage caused by use in a humid area, improper cleaning, neglect, alteration,
fire, theft, non-recommended temperature use and does not apply to minor
imperfections, scratches, stains, discoloration, surface markings as a result
of shipping or other damage to external or nternal surfaces which does not
impair the utility and/or functionality of the product.
TO OBTAIN SERVICE
If service should be necessary, you should contact IRIS USA, Inc. Customer
Service (“Customer Service”) at
1-800-320-4747.
You may then return the properly packaged product(s), (using adequate packing
and shipping material to prevent damage in transit}, with postage prepaid
along with name, address, telephone number, model number, and proof of date of
purchase (a copy of the receipt) and a detailed description of the claimed
defect. This warranty shall not cover any damage incurred to the products
during transit to Customer Service. You shall have the obligation and
responsibility to: pay for all services and parts not covered by the warranty.
MANUFACTURER’S OBLIGATION
The Warranty may not be altered, expanded, extended, revised or varied except
by written instrument executed by the Manufacturer.
THE MANUFACTURER’S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR
REPLACEMENT OF THE DEFECTIVE PRODUCT(S) AT THE MANUFACTURER’S SOLE AND
EXCLUSIVE OPTION. THE MANUFACTURER WILL REPLACE ANY ITEM FOUND TO BE DEFECTIVE
IN MATERIAL OR WORKMANSHIP WITH THE MOST COMPARABLE CURRENT ITEM. IRIS USA,
INC. DOES NOT ACCEPT SPECIAL REQUESTS, NOR DO WE HAVE THE ABILITY TO UPGRADE
IN EXCHANGE FOR MONEY. THE MANUFACTURER SHALL NOT BE LIABLE FOR ANY SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES, WHETHER DIRECT OR INDIRECT. THE
WARRANTIES SET FORTH HEREIN ARE EXCLUSIVE AND NO OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE OR USE ARE MADE WITH RESPECT TO THE PRODUCTS.
Some states do not allow the exclusion of limitation of incidental or
consequential damages, so the above limitation exclusions may not apply. This
Warranty gives specific legal rights, and there may also be other rights which
vary from state to state.
DISCONTINUED ITEM RETURNED
If the tem returned is discontinued and is no longer available, IRIS USA, Inc.
will automatically replace your item with the most comparable tem currently
manufactured.
Attn: Customer Service (Returns Department)
IRIS USA, Inc.
13423 West Cactus Road
Surprise, AZ 85379
©2019 IRIS USA, Inc. All rights reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>