Electric Spin Scrubber SD-808 Electric Cleaning Brush Instruction Manual

Electric Spin Scrubber SD-808 Electric Cleaning Brush

Product Information

Specifications

• Product Name: Electric Cleaning Brush
• Product Model: SD-808

Product Usage Instructions

Charging the Product

1. Before using the product, please charge it for 3-5 hours to ensure that the machine is fully charged.

Selecting and Installing Brush Head

1. Select the suitable brush head according to the desired cleaning occasion.
2. Power off the machine before replacing the brush head.
3. Install the brush head on the rotation disc of the host.

Using the Product

1. Long press the switch key to turn on the machine.
2. The machine will enter the low-speed rotation mode (H1).
3. Press the switch key once to enter the middle-speed rotation mode (H2).
4. Press the switch key again to enter the high-speed rotation mode (H3).
5. To power off, long press the switch key in the power-on state.

Adjusting the Host Angle

To adjust the host angle:

1. Press the locking keys (left side & right side) simultaneously with your right hand.
2. Rotate the machine body to 180 degrees with your left hand.
3. To straighten the machine body, operate it in the opposite direction.

Cleaning & Maintenance

1. Before cleaning, ensure that the sealing rubber plug is tightly inserted into the charging hole.
2. Do not use steel wire or abrasive detergent to clean the brush head and machine body surface.
3. To clean the brush head, rinse it under the water tap or immerse it in water while the product is in high-speed shift (do not immerse the machine body).
4. After cleaning, tumble-dry the product and wipe it with a dry cloth.
5. Do not use hot water (higher than 60°C) to clean the brush head and the product.

Friendly-environmental Disposal

1. When discarding the product, do not mix it with general domestic garbage.
2. Deliver the product to the designated recycling center of the manufacturer for proper disposal.
3. Before discarding, remove the built-in charging batteries and dispose of them properly to avoid environmental contamination.

Frequently Asked Questions (FAQ)

• Q: What can I use the brushed disc with imitated wool for?
• A: The brushed disc with imitated wool can be used for surface polishing, waxing, dedusting, etc. It is suitable for high-end homewares, electric appliances, and automobiles.
• Q: What is the fiber brushed disc mainly used for?
• A: The fiber-brushed disc is mainly used for heavy oil dust removal on surfaces and surface polishing. It is suitable for the kitchen, range hood, wall, bath, etc.
• Q: How long should I charge the product before using it?
• A: Please charge the product for 3-5 hours before use to ensure it is fully charged.
• Q: Can I adjust the angle of the host while using the product?
• A: Yes, you can adjust the host angle by pressing the locking keys and rotating the machine body.
• Q: How do I replace the brush head?
• A: To replace the brush head, power off the machine and install the new brush head on the rotation disc of the host.
• Q: Can I clean the brush head underwater?
• A: Yes, you can rinse the brush head under the water tap or immerse it in water for cleaning. However, do not immerse the machine body in the water.

Introduction of product functions

Switch key: Press the switch key for 2 seconds manually, and the machine starts running and enters into low-speed rotation (H1), and the working indicator is always on, it shows the current electricity volume. During machine operation, if you press the switch key with your hand, the machine enters middle-speed working mode (H2), if you press the switch key again, the machine enters into high-speed working mode (H3). After power-on, if you long press the switch key, the machine will shut down, and all the indicators are off.
How to turn on / turn off the illuminating lamp

1. When the host is in a power-off state, double-click the switch key continuously to turn on or turn off the illuminating lamp;
2. During operation, after the display screen shows the electricity digits, if you double-click the switch key continuously, you can turn on or turn off the illuminating lamp. Press the locking keys on both sides (Left & right )to rotate the angle of the machine body.

If it occurs due to improper operation or overload of the brush head, or it’s stuck, the indicator will glitter twice, and then the machine will activate overload protection and shut down. After troubleshooting, the user can boot again for normal use.
When charging, the red indicator on the display screen glitters, when it’s filled with electricity,the red indicator will be always on.

Introduction to basic functions of the product

The product is mainly used for cleaning domestic bathrooms, the kitchen, floors of the drawing room, furniture, auto, etc spots, the product uses a high-performance lithium battery, with a strong power motor & three-shift speed. The user can change the cleaning strength according to different demands. It uses a TYPE-C charging cable which is widely used all over the world, you only need to charge for 3-5 hours, and the circuit design has an overcharging protection function.

Description of product structure

1. USB cable
2. Host
3. Mesh bag
4. Large flat brush head
5. Small flat brush head
6. Pointed brush head
7. Small mop
8. Imitated wool brush
9. Fiber brush
10. Sponge brush
11. Small brush discholder
12. Connecting rod

Warning

1. Please carefully check whether or not all the accessories are equipped before using it.
2. Please don’t place the charger in a humid environment.
3. During cleaning, you shall inspect whether the sealing rubber plug has been tightly inserted into the charging hole.
4. After cleaning, please timely wipe the surface to make it dry.
5. Don’t let an unsound person or someone who is mentally ill or lack soft related experience and knowledge (including kids) use the product unless they are guided or supervised by the responsible person who could guarantee their security when the mentioned persons use the product.
6. Please take care of kids, to ensure they won’t play the product.
7. During cleaning, please don’t use hot water, when you use warm water, please remember to check the water temperature (it can’t be too hot), to prevent your hands from scalding.
8. During cleaning, it’s forbidden that your hand or your clothes touch the moving parts.
9. When you replace the brush head, please don’t use screw driver etc tools to prize the brush head. Please refer to Page 6 to learn about the correct method of replacing the brush head.
10. When you replace the brush head, your hand can’t touch the switch, to avoid accidental power-on and injury.
11. When you use it, please be far away from cable, rope etc wrapping parts.

Introduction of the charging function

1. Unplug the sealing plug of the charging hole, please use the equipped charging cable to insert into the charging hole. The red indicator on the display screen will glitter in a circulating way. (See figure 2).
2. Then or mal charging time of the product is around 3-5 hours.
3. When the red indicator is always on, it means it’s filled with electricity, unplug the charging plug and remove the charger from the power socket, and tightly insert the sealing rubber plug into the charging hole, to avoid that water into the charging hole when charging(See figure 3).

Introduction of brush head functions

1. Large flat brush head: it’s applicable for bath, kitchen, drawing room, toilet, window, glass etc spots, it’s used to get rid of oil dust/smudge. (See figure 4).
2. Small flat brush head: it’s applicable for wash basin, kitchen sink, furniture etc small-area flat surface cleaning. (See figure 5).
3. Pointed brush head: it’s applicable for the corners, borders and crevices of home kitchen, bath, or range hood, as well as the hub of auto, and those places that are difficult to touch in the course of cleaning. (See figure 6).
4. Small mop: it’s mainly used for floors of the drawing room, glass, tea table, auto surface cleaning/polishing etc (See figure 7).

Attention: When you use a 7-10 brush disc, the brush disc needs to adhere to the brush disc foundation (11) first, and then install the brush disc foundation on the rotation plate of the host when using it.

• The brushed disc with imitated wool can be used for the surface polishing, waxing & dedusting, etc of high-end homewares, electric appliances, autos, etc. (See figure 8).
• The fiber-brushed disc is mainly used for heavy oil dust removal on the surface & surface polishing (See figure 9) aiming at the kitchen, range hood, wall, bath, etc.

How to use the product

1. Before using it, please first charge it for 3-5 hours, to make sure that the machine is filled with electricity.
2. Please select the suitable brush head according to different occasions, and install the brush head on the machine.
3. After you long press the switch key to turn on the machine, it will enter into the low-speed rotation mode (H1), and after pressing it once, it will enter into the middle-speed rotation mode (H2). And when you press it again, it will enter into the high-speed rotation mode (H3). If you long press the switch key in the power-on state, it will power off.

How to replace the brush head

1. When you replace the brush head, firstly you shall power off the machine, and your hand shall be away from the switch key when replacement.
2. Installation method of brush head: install the brush head on the rotation disc of the host, press the locking key of the brush head with your right hand, and grasp the brush head with your left hand for rotation to the left, until you hear a sound of “Ka”, it means you finish the installation of brush head (See the following figure).
3. Disassembling method of brush head: Press the locking key of the brush head with your right hand, grasp the brush head with your left hand for rotation to the right, and then you can easily remove the brush head (See the following figure). (Don’t forcedly pull & disassemble the brush head, because it would damage the machine.)
4. When you use a brush disc or mop, please first adhere the brush disc on the foundation, and then install the brush disc holder on the machine with the same method as the installation method of the brush head.

How to adjust the host angle when using the product
Press the locking keys (left side & right side) at the same time with your right hand, and rotate the machine body to 180 degrees with your left hand, if you want to make the machine body straight, you only need to operate it in opposite direction (See the following figure).

How to clean and maintain

1. When cleaning, please check whether the sealing rubber plug has been tightly inserted into the charging hole.
2. Please don’t use steel wire etc metal objects abrasive detergent or corrosive liquid (such as gasoline or acetone) to clean the brush head & machine body surface.
3. You can rinse the brush head of the product under the water tap or adjust the product to high-speed shift, and immerse the brush head into water for cleaning, don’t immerse the machine body in water.
4. After cleaning, please tumble-dry the product and wipe it with a dry cloth.
5. Please don’t use hot water (higher than 60℃) to clean the brush head & the product.

Friendly-environmental Disposal

1. When you discard & dispose of the product, please don’t pile it with the general domestic garbage together. You shall deliver it to the designated recycling center of the manufacturer, which is good for environmental protection.
2. The built-in charging batteries are probably to contaminate the environment. So when you discard the product, you are sure to take out the batteries first and dispose of the batteries properly.

Thanks for your purchase!
The manual before using it, and keep it properly for future reference.
Theinstructionsincludetheusagemethodsoftheelectriccleaningbrush& some usage techniques, which could make you use it easily and make your home more comfortable& cleaner.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>