jiuhui Shock Skid Walking Machine Instruction Manual

jiuhui Shock Skid Walking Machine

FEATURES

Congratulations on choosing the motorized treadmill. You have taken the first step to a healthier and more rewarding lifestyle. The treadmill is specially designed to meet your needs. The following are the features of the treadmill.

ASSEMBLY

Assemble the Feet

1. Stand up the treadmill with the top on the floor as shown below.
2. Install each foot in the positions as marked in the diagram.

PRECAUTION

TO REDUCE THE RISK OF ELECTRIC SHOCK, BURN, FIRE OR OTHER INJURY, PLEASE READ THE FOLLOWING CAUTIONS AND INFORMATION BEFORE OPERATING THIS TREADMILL.

• It is the responsibility of the owner to be sure that all the users of this treadmill are informed of all warning and precautions.
• Keep pets and small children away from the treadmill at all times.
• Never start the treadmill while you are standing on the walking belt.
• The treadmill is capable of high speeds. To avoid sudden jumps in speed, adjust the speed in small increments.
• Regularly inspect and tighten all parts of the treadmill. Keep hands away from all moving parts.
• Never leave the treadmill unattended while it is running. Always remove t he safety key and move the on/off switch to the “off” position when the treadmill is not in use. Refer to the console instructions page of this manual for the location and operation of the on /off switch.
• Never leave the treadmill unattended when plugged in.
• When folding or moving the treadmill, make sure that the safety lock is fully engaged. Do not remove the motor cover unless instructed to do so by an authorized service representative. Servicing other than the procedures in this manual should be perf ormed only by an authorized service representative.
• Keep the plug and power cord away from heated surfaces.
• Keep all electrical components, such as the motor, power cord and on/off switch away from water or other liquids to prevent shock. Do not set anyt hing on the handrails, computer console or belt.

FOR YOUR OWN SAFETY, BE ADVISED OF THE FOLLOWING:

• Assemble and operate the treadmill on a solid level surface. Keep at least four feet of clearance around the treadmill at all times.
• Always insert the safety key and attach the clip to your clothing on your waist before commencing your workout. If you should encounter problems and need to stop the motor quickly, simply pull the cord to disengage the safety key from the console. To continue operation, simply reinsert the safety key into the console.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• Remove the safety key and store it in a safe place when the treadmill is not in use. Keep the safety key away from children.
• Wear the proper exercise clothing and shoes for your workout. Do not wear loose clothing or shoes with leather soles or heels. Be sure to tie long hair back.
• Keep all loose clothing and towel s away from the running surface. The belt will not stop immediately if an object gets caught in the rollers or belt. Should an object gets caught, turn the unit off immediately.
• Proceed with caution when getting on or off the treadmill. Use the handrails whenever possible. Step onto the running belt only when it is running at a very slow speed. Do not step off the treadmill while the belt is moving.
• To get on or off the running surface, straddle the running surface by standing on the right and left platforms on each side of the belt before starting the belt (to begin your workout) and after it has stopped (at the end of your workout).
• Never attempt to turn around while on the treadmill with the belt running. Keep your head and body facing forward at all times.
• Never turn on the treadmill while someone is standing on the running surface.
• Do not rock the treadmill, stand on the handrails or computer console at any time.
• Do not overexert yourself during your workout. Stop your workout immediately if you feel overexerted. If you feel any pain or discomfort, please consult your physician.
• Do not attempt any service on the treadmill yourself other than the assembly and maintenance described in this manual. The treadmill is for household use only. Please refer to the customer service information contained in this manual should your treadmill require additional service other than that described in this manual.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

ELECTRICAL SAFETY :This motorized treadmill must be grounded. Should it break or malfunction, grounding reduces the risk of shock. The treadmill is equipped with a power cord having an equipment grounding conductor and a grounding plug. Th e plug must be inserted into an appropriate outlet that is properly installed and grounded by all local codes and ordinances.

IMPORTANT : Improper connection of the equipment grounding conductor can result in a risk of an electric shock. If you are in doubt as to whether the treadmill is properly grounded, check with a qualified electrician or service person. Do not modify the plug provided with the treadmill. If it does not fit the outlet, then get a proper outlet installed by a qualified technician.

SURGE PROTECTION : Although this treadmill is equipped with built-in surge protection, an external surge protector is still recommended. The treadmill will shut off automatically if it encounters a surge in power. A reset button is located at the e lower front of the motor cover. If the treadmill should be shut down, turn the on/off switch to the “off” position, then press the reset button. The treadmill will now work properly.

CONSOLE PANEL

CONSOLE PANEL

REMOTE CONTROL

1. Press the triangle to start the treadmill. , press the square to stop the treadmill.
2. SPEED”+”: speed + button, at the running state, press it will be add 0.1M/H every time , press it for a long time,it will add the speed constantly;
3. SPEED” SPEED”–“: speed button, at the running state, press it will decrease 0.1KM/H every time, press it for a long time, it will decrease the speed constantly.

DISPLAY

1. Speed window ; at the running state, it will show speed range; 0.6 3 .8M/H
2. Calories window ; at the running state, it will show calories
3. Time window ; at the running state, it will show running time
4. distance window ; at the running state, it will show running distance
5. step window ; at the running state, it will show step number

ERROR SIGNAL
Please check the error Signal display of the window

E01

|

Display did not receive the signal

| Cable connection| Check or replace the Cables
display default| replace the display
controller default| replace the controller

E02

|

The problem between controller and motor

| motor connect wires did not connect well| Check that the motor wires are connected correctly
No voltage output or abnormal voltage output of controller board|

replace the controller

motor default| replace the motor

E03

|

The speed is abnormal

|

The photoelectric sensor is not properly assembled on the motor

|

reassemble the sensor

Poor photoelectric sensor| replace the sensor
Failure of controller board| replace the controller

E04

|

overvoltage

| Input voltage   too high| adjust the voltage
motor default| replace the motor
Failure of controller board| replace the controller

E05

|

overpower current

| power current too high| adjust the power current
Problems with the assembly structure of the treadmill and the motor cause motor resistance or

blockage

|

check the structure if it is well

controller default| replace the controller

E06

|

overvoltage

| Input voltage   too low| Please check whether the power

supply line is normal

Failure of controller board| replace the controller

OPERATION INSTRUCTION

PREPARATION BEFORE START

1. Plug in the power cord . If the machine is not operated or moved for a long time, please turn off the power.
2. Always take the remote control on your hand to start or stop the treadmill.

START

1. Press the triangle the machine begins to work with a starting speed 0.6 M/h
2. Press “ ““–” can control the speed, with one press 0.1 M/h will be increased or decreased. Press the key without stopping can get to the speed you want. The highest speed is 3.8 M/h while the lowest is 0.6 M/h.

WAY TO STOP THE MACHINE

1. Press the square the machine will stop working

IMPORTANT SAFETY INSTRUCTION

1. The machine is for home use
2. The voltage for the machine is 11 0V.
3. Before operating the machine, please do 10 minutes warm up and wear clothes and shoes that are suitable for sports
4. Do not stand on the motorized treadmill when you adjust, test or start the motorized treadmill.
5. Be careful when you get on or off the machine. Before starting the machine, please place your feet on the side rails (not the running belt). After starting the machine, stand o n the belt with the machine operating at the lowest speed. Then increase the speed gradually. Before getting off the machine, please decrease the speed to the lowest level in case of any danger.
6. When operating, press the safety at any time, the motor will stop working and the controller will give warnings.
7. Children should be supervised by adults when they play on or beside the machine.
8. The motorized treadmill should be protected from sunshine, damp and dirt. All the parts shall be cleaned often.
9. When the machine is free from use for a long time, please don’t place any objects or stand on the machine.

MAINTENANCE

To prolong the use time of the motorized treadmill, regular maintenance is necessary.

1. When the machine is operated for the first time or fo r a long time, some lubricant on the running deck or the back of the running belt is necessary in order to lessen the burden of the motor.
2. Clean the parts of the machine regularly to prevent dirt from disturbing the operation of the parts.
3. Drop some lubric ant on the axletree of the roller regularly to keep the axletree in good condition.
4. Check the screws and bolts regularly. If they are loose, please screw them down.

LUBRICATION
The treadmills have already been spread with “Silicone Oil” in advance before leaving the manufacturing plant. Silicone oil is without volatility and has gradually permeated through the running belt. There will be no need to re spread the oil in normal circumstances. To maintain the running belt, we have included a small bottle of “Silicone Oil”. “Silicone Oil” may be re spread once the resistance has been increased and the running belt starts rubbing against the running deck. To hold open the running belt from two sides, apply the silicone oil with an even motion on the centre r of the running deck. Allow the silicone oil to ‘set’ for one minute before using the treadmill.Attention: Only use “Silicone Oil” lubricants for this equipment. In addition, do not add any other oil ingredients; otherwise, the treadmill will be damaged. Do not over-lubricate the walking board. Excess lubricant should be wiped off with a clean towel.

RUNNING BELT ADJUSTMENT

1. If the belt has drifted to the right (see figure A):
   • Turn off the treadmill and unplug the treadmill.
   • Using the Alle n wrench, turn the right adjusting belt ¼ of a turn clockwise.
   • Plug the treadmill back in and turn it on. Observe the treadmill running for deviations.
   • Repeat the steps above until the running belt is centered and running centered down the platform.
2. If the running belt has drifted to the left (see figure B):
   • Turn off the treadmill and unplug it.
   • Using the Allen wrench, turn the right adjusting belt ¼ of a turn counterclockwise.
   • Plug the treadmill back in and turn it on. Observe the treadmill running for deviations.
   • Repeat the steps above until the running belt is centred and running centred down the platform.
3. Overtime, the running belt will gradually become slack. The belt can be tightened using the following instructions (see figure C):
   • Turn off and unplug the treadmill.
   • Using the Allen wrench turn each adjusting bolts clockwise ¼ of a turn.
   • Power on the treadmill, then stand on the belt to confirm the tightness of the belt.
   • Repeat the previous steps until the belt is at moderate tightness.

EXPLODED DRAWING

PARTS LIST

FCC STATEMENT

NOTE
Changes or modifications not expressly approved by the party responseble for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B di gital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not in stalled and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference t o radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications to this unit not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.

FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Bluetooth App Manual

FitShow Download

Scan QR code to download the APP directly, or download and install over the application stores by search ‘FitShow’.

Application Operation

User register/signup and login

1. 【1 】 Generate a verification code to log in directly
2. 【2 】 Tap ‘More’ –> Password Login to input the existing a ccount and password
3. 【 3 】 Log in as a guest

Device Connection

Before connecting the device, please make sure the system Bluetooth and GPS(Andoird8.0 and above required) are ON status. Then go to the [Sports Devices] page, and get the devices nearby via Bluetooth search.

Note:

1. Please do not bind devices by the phone Bluetooth list which will disable the APP.
2. If the device is powered by battery, please run the device one or two to activate the device then connect APP.

Model Selection

Tap a model 【 1 】 to enter the corresponding sports model. And connect the desired device by the nearby devices list 【 2 】.

Sports Control

Start the treadmill to enter the sports car table, and control the sports by the 【 1 】 control options. The motion data is generated synchronously after the sports.

Sports Training

Enter [SPorts Training] page, make a daily sport plan by the 【 1 】 . Once the plan is created, tap 【 2 】 to start the plan.

Outdoor Sports

• Enter the [Sports OutDoor] page to start a related outdoor sports model.

Discover

Enter the [Discover] page to find more sports, diet, courses, and other wonderful content recommendations.

My

Enter [My] page to view the sports data record, edit the profile, change system setting, and so on.

The Third Party Application

Kinomap

Search, download, and install Kinomap over the App Store.

1. 【 1 】 Enter Kinomap to select [More] page;
2. 【 2 】 Select to add more fitness equipment;
3. 【 3 】 Select the desired device type;
4. 【4 】 Tap FiteShow entrance;
5. 【 5 】 Tap the matching devices like ‘Fs XXXX’ to bind Find related videos to start sports. 【 6 】 Find related videos to start sports.

ZWIFT

Search, download, and install ZWIFT over the App Store.

1. 【 1 】 Enter ZWIFT to register an account;
2. 【 2 】 Login account to select the paired riding or running equipment;
3. 【 3 】 Pair device successfully, tap OK to start sport;
4. 【 4 】 For riding equipment, start riding directly. For running equipment, need to press the start button to start running.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>