Interthings Technology IPC202 Smart Outdoor Camera User Manual
- June 1, 2024
- Interthings Technology
Table of Contents
- Interthings Technology IPC202 Smart Outdoor Camera
- 1. What’s included
- 2. Parts of the Camera
- 3. Initial Setup
- Install the App
- Register an account
- 4. Connecting Your IP Camera with the App
- 6. FAQ
- FCC WARNING
- Specifications:
- Frequently Asked Questions (FAQ):
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Interthings Technology IPC202 Smart Outdoor Camera
USER MANUAL
1. What’s included
2. Parts of the Camera
3. Initial Setup
DESCRIPTION:
Power DC 5V +/- 5%
Status lights:
- Blue light solid on: system setup
- Blue light blinking fast: waiting for the pairing
- Blue light blinking slowly: waiting for the WiFi connection
Microphone Capture sound for your video
SD Card slot Support local micro SD Card storage (Max. 128GB)
Reset Press and hold the reset button for 5 seconds to reset the camera (if
you have modied the settings, they will return to factory defaults)
Before you start write down your network name & password.
Note: this item only works on a 2.4GHz Wi-Fi network, not on a 5GHz network.
Please consult your router manual for settings.
Please follow the instructions and make sure the passwords are correctly
inputted.
One device can only be paired with one App account at a time, if the device
has already been paired with another account, then it can’t be paired to
another account.
The device can be removed from the app account by being deleted from the app.
The device will be reset automatically once the blue light changes to a solid
on.
Preparations before use
Mobile device system requirements:
- Android OS 4.4 or higher
- iOS 9.0 or higher
Install the App
Use your mobile phone or tablet to search for “TuyaSmart” in Google Play (for Android OS) or in the Apple app store(for iOS) to find the app, and install it according the instructions.
Register an account
If this is the first time using the app, an account need to be registered as below:
4. Connecting Your IP Camera with the App
Note: Your IPC Camera is supported only on a 2.4GHz Wi-Fi network. For setup, make sure your mobile device is connected to a 2.4GHz Wi-Fi network
1. After installing the app ‘Tuya Smart’, open the app and follow the prompts
to setup the app.
Then tap ‘+’ or ‘Add Device’ from the home page.
Tap ‘Security & Sensor’, the choose ‘Smart Camera’.
2. Power the device on and hear the sound of ‘camera start’.
Make sure your smart device is connected to a 2.4G Wi-Fi network, then tap
‘Confirm’.
3. The app will guide you to scan mobile device with the camera.
When you tap ‘Continue’ the mobile phone displays a QR code.
Hold the camera 15 to 20 cm in front of the mobile device for the camera to scan the QR code.
4. In connecting, make sure your router, mobile and device are as close as
possible.
Once the camera get the information from mobile device, the camera will have a
sound ‘camera configured’ which means the camera is connected successfully.
Your camera’s Live Camera view with streaming video will be openned.
6. FAQ
PROBLEM | CORRECTIVE ACTION |
---|---|
Camera will not connect to my Wi-Fi network | 1. Make sure the Wi-Fi signal is |
flashing. If the Wi-Fi signal is not flashing, you will need to press and hold
Reset Button located at the back of the camera(see the Description section).
2. Make sure the Wi-Fi network is a 2.4GHz network, device will not connect
to a 5GHz network.
3. Test your Wi-Fi network work with other devices such as your phone or
computer to make sure it is operation properly .
4. The Wi-Fi connection may be out of range during pairing. Use your phone to
check range, it is recommended to have at least 2 signal bars showing for
proper connection.
5. Your Wi-Fi network password is case sensitive, make sure you are entering
it correctly.
The camera is off-line| 1. There could be a temporary issue with your
internet connection
(e.g., service disruption). Please try again in a few minutes.
2. Make sure your Wi-Fi router is turned On.
3. The camera may not have power to it, make sure the wall switch and breaker
is in the On position.
4. Make sure the camera is getting a good signal from your Wi-Fi router. Use
your phone to check range, it is recommended to have at least 2 signal bars
showing for proper connection.
5. The camera may have been disconnected from your Wi-Fi network, press and
hold Reset Button(see the Description section) until you hear an audible tone.
How to reset the camera to reenter pairing mode?| 1. Press and hold reset
button located at the back of the camera (see Description section) until you
hear an audible tone.
The camera is not recording?| 1. Make sure Record Switch is turned On in APP,
under SD Card Settings. This is located in Settings menu on the upper
rightcorner in the control panel.
2. Make sure that the microSD card is installed correctly. To confirm the
camera is recognizing the microSD card, go to the SD card Settings in the
Settings menu and make sure microSD Card capacity shows Total capacity, Used
and Free space. If this does not appear you may consider reformatting the
microSD card.
3. WARNING: Reformatting microSD card will delete all videos stored on card.
Please go through the troubleshooting section before doing so.
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm distance between the radiator and your body:
Use only the supplied antenna.
Specifications:
-
Resolution: 420x128MM
-
Model: IPC202
-
Components: Camera, Power adapter, Screw package
-
Microphone Status light
-
SD Card slot (Supports local micro SD Card storage up to 128GB)
-
-
Frequently Asked Questions (FAQ):
Q: How do I reset the camera?
A: Press and hold the reset button for 5 seconds to reset the camera. This will restore the settings to factory defaults.
**Q: What is the maximum storage capacity supported by the SD Card
slot?**
A: The SD Card slot supports local micro SD Card storage up to 128GB.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>