CUBE Fold Hybrid Bikes Instruction Manual

June 16, 2024
CUBE

CUBE logo Operating manual
Faltmechanismus CUBE Fold Hybrid

Operating manual to the folding mechanism of the CUBE Fold Hybrid

CUBE Fold Hybrid Bikes - Operating

  1. Frame
  2. Folding joint
  3. Carrying handle
  4. Saddle
  5. Seat post
  6. Seat clamp
  7. Battery
  8. Brake
  9. Rear carrier
  10. Rear light
  11. Mudguard
  12. Hub
  13. Cassette
  14. Rim
  15. Tire
  16. Spoke
  17. Rear Derailleur
  18. Chain
  19. Kickstand
  20. Chain ring
  21. Crank arm
  22. Mid-drive motor
  23. Fork
  24. Folding stem
  25. Headlight
  26. Display
  27. Brake lever
  28. Shifter
  29. Grip

General notes on these operating instructions
NOTICE

The exclamation mark (without tri‐angle) alerts you to information that requires special attention.
WARNING
The yellow warning triangle in combination with the signal word “Warning” indicates dangers that can lead to slight personal injury and damage to property.
DANGER
The yellow warning triangle in combi‐nation with the signal word “Danger” indicates dangers that can lead to severe personal injury (up to death).
General information
This supplementary operating manual is intended to familiarize you with the correct handling of the folding mechanism of your Fold Hybrid.
If you should have any further questions about the correct operating of the folding mechanism of your Fold Hybrid, please always contact your CUBE Specialist Dealer.
NOTICE
Always make sure that your Fold Hybrid stands securely when you transport it in the folded state.
Especially when transporting in public transport and in the car, make sure that the bike is secured against falling over.
When falling over, your bike can be damaged.

Folding process

WARNING
The e-bike system must always be switched off before starting the folding process.
Failure to do so may result in the motor assistance of the e-bike system kicking in and causing injury.
NOTICE
Before starting the folding process and for transport in the folded state, remove any luggage from the bike.
NOTICE
To get a smaller pack size of the bike when needed, the pedals can be folded.

  1. Park your bike safely on the kickstand.CUBE Fold Hybrid Bikes - FoldingFig. 1: bike on kickstand

  2. Fully retract the seat post and the height-adjust‐able stem by using the quick-release levers.CUBE Fold Hybrid Bikes - Folding 1Fig. 2: Draw in Seatpost + stem

  3. Fold the stem as shown in the following figures.
    ? Unlock the safety lever (1) of foldable stem by pushing the round unlocking button (2).CUBE Fold Hybrid Bikes - Folding 2? Fold down the stem together with the han‐dlebars.CUBE Fold Hybrid Bikes - Folding
3Fig. 3: Fold stem

  4. Unlock the folding mechanism on the frame.CUBE Fold Hybrid Bikes - Folding 4Fig. 4: Unlock folding mechanismCUBE Fold Hybrid Bikes - Folding 5Fig. 5: Fold frame joint
    1 Press push button.
    2 Open frame lock.

  5. Swing the front frame part to the rear frame part.CUBE Fold Hybrid Bikes - Folding 6Fig. 6: Swing front frame part (close)

  6. By a slight pressure the fork locks on the Klickfix Quadlock adapter.CUBE Fold Hybrid Bikes - Folding 7Fig. 7: Close Klickfix Quadlock AdapterCUBE Fold Hybrid Bikes - Folding 8Fig. 8: Klickfix Quadlock Adapter closed
    ? WARNING
    Check that the Klickfix Quadlock adapter is fully engaged between fork and rear triangle.
    Otherwise, the Fold Hybrid can be open during trans‐port and result in injuries.

  7. Before transporting the bike, fold the kickstand back in.
    ? Your bike is now completely folded and can be transported safely with the help of the carrying handle.

Build up

NOTICE
Before you start setting up the Fold Hybrid, unfold the kickstand and place the bike on it.CUBE Fold Hybrid Bikes - BuildFig. 9: Bike folded on stand

  1. Open the lock by pressing the Klickfix Quadlock adapter.CUBE Fold Hybrid Bikes - Build 1Fig. 10: Open Klickfix Quadlock Adapter
    1 Press the release mechanism of the Klickfix Quad‐lock Adapters.
    2 Detach the front frame part from the adapter.

  2. Swing the front frame part 180° into the driving direction until the joint is closed.CUBE Fold Hybrid Bikes - Build 2Fig. 11: Swing front frame (open)

  3. Lock the Frame jointCUBE Fold Hybrid Bikes - Build 3Fig. 12: Close and lock frame joint
    1 Close the frame joint completely.
    2 Lock the folding mechanism by engaging the lever in the ball head.CUBE
Fold Hybrid Bikes - Build 4Fig. 13: Lock the folding mechanism by engaging the lever in the ball head
    ? DANGER
    Make sure that the frame joint is fully closed and the lever is correctly locked in the ball head.
    Otherwise, the joint of the frame may open while driving.
    This can lead to dangerous driving situations, falls, acci‐dents and property damage.

  4. Set up the stem as shown in the images.CUBE Fold Hybrid Bikes - Build 5Fig. 14: Set up stem
    ? Push the lever all the way down.CUBE Fold Hybrid Bikes - Build
6? Fully straighten the stem, the upper part  must be flush with the lower part.CUBE Fold Hybrid Bikes - Build 7? Lock the lever on the stem in the upward position.CUBE Fold Hybrid Bikes - Build
8 DANGER
    Make sure that the stem joint is fully closed and the lever is correctly locked.
    Otherwise, the stem joint may open while riding.
    This can lead to dangerous driving situations, falls, acci‐dents and property damage.

  5. Adjust the saddle and stem height to your needs for safe riding and guiding of the bike.CUBE Fold Hybrid Bikes - Build 9Fig. 15: Adjust stem and saddle height

DANGER
Observe the correct inser‐tion depth of the seat post.
The maximum distance to which the seat post can be pulled out of the frame is marked on the seat post.
Never pull the seat post out further than this marking!
Otherwise, the seat post may come loose from the frame.
This can lead to dangerous driving situations, falls, acci‐dents and property damage.
NOTICE
If the pedals have been folded, return them to their original position.
Fold the kickstand back in before starting to ride!
? Your bike is now fully assembled and ready to ride.

Legal notice
Manufacturer:
Pending System GmbH & Co. KG
Ludwig-Hüttner-Straße 5-7
95679 Waldershof
Germany
www.cube.eu
info@cube.eu
FON: +49(0) 9231-97 007 80
FAX: +49(0) 9231-97 007 199
Status: March 2023

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals