Cube Electronics Co Ltd HM502 Motorcycle DVR Dash Camera Installation Guide

HM502 Motorcycle DVR Dash Camera

“`html

Product Specifications

• TF Card Support: Up to GB
• Built-in eMMC Storage: GB
• Waterproof Rating: IP

Product Usage Instructions

TF Card Installation

1. Use a screwdriver to open the plug. Do not remove the stuck
   screw.

2. Push down the plug and insert the TF card with the metal side
   up towards the main screen side.

3. Cover the plug and tighten the screw after installing the TF
   card.

4. Before installing the TF card, transfer all data to another
   storage device.

5. When using the TF card for the first time, format it to delete
   all data. Press OK to finish formatting.

Main Host Bracket Installation

1. Adjust the angle of the main host before installation and
   choose the right spacer based on your motorcycle handlebar.

2. If using spacers, ensure proper cooperation with other
   components.

3. Tighten the screws securely after adjusting the angle and
   placing the main host.

Front and Rear Camera Installation

1. When installing the camera bracket, ensure the mark indicating
   the top is correctly positioned.

2. Use the provided screws to attach the front and rear cameras
   securely.

Stainless Steel Main Host Bracket Installation

1. Use the inner hexagon screws to attach the stainless steel main
   host bracket securely.

2. Ensure proper positioning and attachment of the L bracket and
   hole filling ring for long hole screws.

Additional Information

– Tilt angle correction and data clearing are required during
initial installation on flat ground for data accuracy.

– Ensure that the main host angle respects the specified range
and stays parallel to the front instrument for accurate data
recording.

FAQ

Q: What is the maximum TF card capacity supported?

A: The device supports TF cards up to GB in capacity.

Q: How should I adjust the main host angle during

installation?

A: The main host should be parallel to the horizontal plane and
aligned with the front instrument for accurate data recording.

“`

HFK
HM

/WARNING
V- V
M HM
TF
Installation guide

. Please read these instructions carefully. . This product supports – V power supply and is designed for use on motorcycles. . Please turn off the power of motorcycle before finishing installation. . When install the camera bracket, please ensure that area is clean. Vehicle waxing will affect the installation effect. Before installation can use lighter or hot gun to heat M sticker. . Do not use high-pressure water gun to flush the machine! . HM cameras are fully sealed waterproof, but still need to avoid using Cleaning Naphtha, alcohol, and Solvents such as tar detergent come into contact with the lens to prevent damage the waterproof layer. . For storage speed and security, please clean the TF card regularly.
PART

TF TF card installation
Use screwdriver to open the plug. The screw is stuck in the plug, please don’t take out.

mm Push down the plug mm

TF G TF Note:TF card metal side up to the main screen side (max support for GB TF card)

TF After installing the TF card, please cover the plug and tighten the screw.
TFTF “TF” Before installing TF card, please transform all data to other storage. First time to install the TF card the screen will have notice”First to use TF card it need to format, it will delete all data”, press”OK”to finish formatting.
Main host bracket installation mm . mm mm mm

/Push
HM eMMC GBTFTFeMMC TF( GBTFTF TFeMMCTFeMMC). Note:HM built-in eMMC GB storage, it can running without TF card. Without inserting TF card, all video files will save in eMMC and loop recording normally. Insert TF card(max support GB),video files will save in TF card, loop recording will only overwrite TF card saved files. When the video locked, the video will saved in TF card and eMMC (if TF card ejected or not well contacted, the video will saved to eMMC).
main host can be rotated in different angles. Please choose right place and adjust the angle before installation, tighten the screws. Please choose the right spacer based on your motorcycle handlebar. There is no need to use spacer when the handlebar is mm.When using . mm and mm spacer, it is necessary to cooperate with mm piece.

M mm M mm inner hexagon screws

M mm M mm inner hexagon screws

M mm M mm inner hexagon screws

Front and rear camera installation
M . mm M . mm inner hexagon screws
M mm M mm inner hexagon screws Multifunction camera bracket

UP This mark should be on the top when you install the camera
,, ,UP Camera bracket kits
M M sticker

WARNING

Stainless steel main host bracket installation

L L bracket
M mm M mm inner hexagon screws

L L bracket
mm
mm Hole filling ring , suitable for long hole screw

IP
This product waterproof IP . Forbidden to use high-pressure watergun to flush the DVR. If damage caused by this reason, no warranty.
1

:
.
. °
Notice:
,Tilt angle correction and data clearing are required during initial installation. Make sure motorcycle on flat ground to ensure the data accuracy.
,During installation, please ensure that the angle between the main host and the horizontal plane is within degrees and keep parallel to the front instrument as far as possible. If it is beyond the range, tilt angle data may cause deviation.

/Correct example

/Standard installation drawing
The main host is parallel to the horizontal plane and keep parallel to the front instrument.

/Error example

20° The angle between the main host and the horizontal plane is over degrees.

The installation drawings

/Error example

Horizontal plane sees the side of main host, the main host and the front instrument are not parallel and the angle is too large.

PART

HM (, B+ ACC

Note: please connect the cable correctly with right color
HM Main Host Power adapter Front camera Rear camera Connect with front camera (The short wire) Connect with rear camera (The long wire) The red cord connect with power adapter Fuse Red B+ (positive) Orange ACC Power The black cord lead to ground (negative) Temperature sensor

install the rear camera on the back of the motorcycle

ACCACC ACC
Note: ACC signal line connected with motorcycle ACC power, can be switched on/off with motorcycle key. It also can be connected to the positive of the motorcycle power supply, so that you need to turn on by manually. Please remember to shut down the DVR after the motorcycle is turned off to avoid power consumption of motorcycle. (Recommended to connect the motorcycle ACC power supply)

Install adapter under the motorcycle cushion

Install the main host on handlebar, convenient to control the machine

Install front camera on front of the motorcycle.

HM702 HM702 operation

PART

Function Buttons and operation

Power key
OK button
Setting button
UP button
Down button

/Working indicator light /Power indicator light
GPS GPS and Beidou dual module
Reset button

/Speaker

% % % % %ACC
—–/ GPS
/WIFI — ——

. .

Power key: Short press to power on the machine, keep pressing over seconds to power off. In boot process, short press to adjust the screen brightness and tilt angle indicator brightness. The indicator brightness is divided in levels: % brightness, % brightness, % brightness and off the screen(indicator off).The default screen brightness is %,The system will save the adjusted brightness. If you turn off the machine in the screen off state, then the brightness is % when you turn on the machine again. If connected with motorcycle ACC power, unscrew the motorcycle key the DVR will automatically start on and recording, off the key the DVR will automatically shut down. “OK”button: Short press in the recording status to pause the recording. After pausing the video, long press to enter in camera interface (short press to take photos-each camera will take one).Long press again will enter in play mode, you can view the videos and pictures (press UP/Down button to select the review file— short press to play — short press again to pause / long press to end play).The third long press to return to the video interface. In speed interface long press seconds to clear the highest speed and the max tilt angle data. In compass interface long press seconds to clear the highest altitude and GPS altitude data. In straight racing interface short press to confirm the selection, long press seconds to clear the racing records. In tilt angle interface long press seconds to clear the tilt angle data or correct tilt angle. In my route interface long press seconds to clear all data records in all interfaces. Setting button: Short press to lock video in recording status, long press to on/off WIFI. After pausing the recording, short press to enter the video settings interface (press UP/Down button to select the items that need to set— press”OK”to enter— press UP/Down to the selection— press”OK”to confirm).Short press again to enter the system settings interface. The third short press to exit settings. UP button: When in recording status, short press to switch the speed interface, recording interface, tire pressure display interface, my route interface, tilt angle interface, straight racing and the compass interface. Long press second for switching front / rear camera to be displayed separately or the front/rear camera size window displayed. In settings interface, this button is up selection function.”Straight racing”interface long press second to up select racing mode. Down button: When in recording status, short press to switch the speed interface, compass interface, straight racing, tilt angle interface, my route interface, tire pressure display interface and recording interface. Long press
second for switching front / rear camera to be displayed separately or the front/rear camera size window displayed. In settings interface, this button is down selection function.”Straight racing”interface long press second to down select racing mode. Working Indicator: When recording it flashes every second, pause recording it always on. Power Indicator: Power on it lights on, the built-in battery fully charged it lights off.

Note: , Turn off the function of”Straight racing”or”Tilt angle”,the interface will no longer display on the

main host screen. , The tire pressure display interface can be opened in the tire pressure setting menu or

after successfully matching with the tire pressure monitor.

2

/Introduction of main host screen interfaces

/Recording interfac

3 K K

00:02:34
240 km/h
1081m GPS1052m
hpa

2024/01/01 12:23:34

/Tiltangleinterface

REC

102

96

MAX
42

102
MAX
39

“OK”
/Tire pressure display interface
REC

FW

. Bar

FW
. Bar

“OK”

/Longitude and latitude /Front tire pressure alarm (/Normal blue, alarm turns red) /Front tire pressure value /Front tire temperature /Rear tire pressure alarm (/Normal blue, alarm turns red) /Rear tire pressure value /Rear tire temperature
HM702/ HM Setting

/Speedinterface

/Straightracinginterface

REC

2:31

REC

1 0 6 km/h

1 3.37

2 3.46

3 3.29

3.55

FW:2.5Bar BW:2.5Bar

1000Km 04:45h

4 4.22 5

96 km/h

0-100 km/h

51 m

0-400 m

“OK”

“OK”

/Compassinterface

/Myrouteinterface

REC

102

330

N

30

GPS

300

60

717 hpa
2811 m

240

W

1 2 4°

E

120

2836 m

MAX

3021 m

150

210

S

N113°5512 E39°2532

“OK”

REC

1252km 120105 104km/h

976m

L:42° R:51° 256km/h

“OK”

()/Recording

GPS/GPS Altitude

0-100km/h Straight racing 0-100km/h

(red light flashing shows DVR is recording now) / AirPressure

0-400m /Straight racing 0-400m

/Time cycle of recording

/ Compass

/Current Speed

/Front camera resolution

/Photo

/Current racing distance

/Rear camera resolution

/Video lock

/

/Ambient temperature

GPS/GPS signal

/Recording voice On/Off

TF/TF card status

/Battery /Recording time length

/Current Speed

/Altitude

/Tire pressure value /Subtotal mileage /Single driving time 5/5 records /Best record 3 3-minute video countdown /Current racing time

Speed at max. tilt angle on the left /Max.tilt angle record on the left /
Speed at max. tilt angle on the right /Max.tilt angle record on the right /Current tilt angle / Compass /Highest altitude

3 ( )
My route: Record the total mileage, total driving time, average driving speed, highest altitude, max.tilt angle, fastest driving speed. In my route interface long press 3seconds to clear all data records in all interfaces, and restart to record. (clear other interfaces data records will not affect any data of my route interface)

“””” “”

Note:1, The “Photo” icon in the pictures will only be displayed when the remote control “Photo” button is pressed, and it will not be displayed after taking photos.”Video Lock” icon will only be displayed

Video

Video

Video

Setup

Setup

Resolution Loop Recording Video Synthesis

Satellite Parking Guard G-sensor

Audio

Date Stamp Compass Air Pressure Altitude

GPS
GPS GPS Altitude

GPS LAL

Speed Fatigue Driving

Straight Racing Delayed
Shutdown

60°

/

Tilt Angle

Conversion

WIFI WIFI

/

Date/Time Auto Matching TirePressure

Time Zone

Language

Format

Default Set

TemperatureScreen Off Delay Beep Sound Image Rotation

Version

• P _ * P
  eMMCTF
  ,
  GPSGPSGPS
  GPS
  ACC

HFK logo
APP APPGPS

GPSGPSGPS GPSGPS
GPSGPS G P S A P P GPS
GPS APPGPS

ACC
/km/hmph

Video settings

Resolution: select the resolution of the video, the default resolution is

P_ *

P , front and rear

cameras keep the same video resolution.

Loop Recording: Set the duration of recording, there are options: minute, minutes and minutes . The default is minutes (each video record minutes). It will keep recording till the eMMC/TF card is full, the new video will overwrite before saved videos.

Video Synthesis: When turn on this function, the video can show both images of the front and rear cameras by picture in picture. The default is off. When turn off this function, the video recording by the front and rear cameras are two different videos.

GPS: Set the GPS on or off. After turning GPS on, it can show the speed , the altitude, the latitude and longitude of the motorcycle, also have the compass function.

After GPS turn off, it will be not able to provide these data.

Satellite: It show the time and date, speed, latitude and longitude, number of satellites, signal value. The larger the signal value, the stronger the signal. If the GPS has no signal or turned off, it will not be able to receive satellite signals.

Parking Guard: seconds of automatic video recording when the motorcycle is hit and the motorcycle key is on”Off”, this function requires ACC to be connected. After this function triggered once, you need to re-set to continue using it.

G-Sensor: Adjust the sensing of the video collision locking function, select the appropriate option according to the road conditions.

Audio: This function is designed for voice recording at the same time when DVR recording, two status: on/off. Off the setting, there is no sound in the video.

Date Stamp: The HFK logo and date will be shown in the video when turn on the DVR. It will be no longer shown in the video when it is turned off. The default is on.

Compass: The default setting is on. When it is turned on, there will have icon in the main screen. In APP, it can be synthesized into the video by adding a watermark. After being turned off, the main screen will not displayed, and the compass watermark can also be added in the APP.

Air pressure: When turned on this function, real-time pressure information will be displayed on the main screen, and pressure data mark will also be generated on the video. After shutdown, the main screen and the video will not displayed. The default setting is on.

Altitude: After turning on the main unit, the real-time altitude information of the area will be displayed on the screen of the host, and the altitude data label will also be generated on the video. After shutting down, neither the host nor the video will be displayed. The default is on.

GPS Altitude: Turn on GPS, the real-time GPS altitude information of the area will show on the screen, When turn off GPS, it will not be shown the GPS altitude information of the area on the screen. The default setting GPS is on. If the GPS has no signal or turned off, the screen will have no GPS altitude data normally.

GPS LAL: After turning on, the current position of the motorcycle will be showed on main screen. The GPS must be turned on to use it. After closing, the GPS latitude and longitude information will not be displayed on the host, but it can be retrieved by adding a watermark in the APP. The default is on. If the GPS has no signal or is turned off, it will not be able to provide data normally.

Speed: After turning on this function, the screen will show the current speed of the motorcycle. Please turn on GPS first to use this function.

Fatigue Driving: After being turned on, after hours of continuous power on, the host screen will display a fatigue driving prompt box with a beeping sound (for seconds), and then remind once every hour. After turning off, there will be no reminder function.

Delayed shutdown: After the motorcycle key is on”Off”, the DVR will delay seconds to shutdown, this function needs to be connected with ACC.

Conversion: Miles per hour and kilometers per hour can be choosed.

3

WiFi5GWiFiHFKAPP APP WiFi / “””” 315 2 3 5 GMT+08:00 eMMCTF

Straight racing

System setting menu WiFi: Turn on DVR’s G WiFi, connected with your phone, you can operate the DVR, download files, video clip etc. Connected with APP the main screen can’t show current images. In recording status, long press setting button can turn on/off WiFi. Date/Time: Manually adjust the time & date, select the format of time & date. Auto Matching: When you use the remote controller pairing, please make sure the remote controller corresponds to the machine. Temperature: Set the temperature units to “” and “”; Temperature display, after turning on, the host screen will display the real-time ambient temperature of the area, and temperature data labels will also be generated in the video. After shutdown, it will not be displayed on the host and video, and will default to enabled; Low temperature reminder: When the ambient temperature is below , the host screen will display a warning box for being careful of slippery roads and accompanied by a beep sound (lasting for seconds). After turning it off, there will be no reminder function. Screen Off Delay: Choose the time of screen on: off, minutes, minutes, and minutes. Off the setting, the screen will stay on, the default is off. Button sound: Turn on/ off the button sound, the default is on. Image Rotation: When the image on the main screen is opposite to the real object, use this function to correct it. Time Zone: Set the time zone of the user’s area, the default is GMT+ : . Language: Set the language by simplified Chinese, traditional Chinese and English. The default is simplified Chinese. Format: You can choose to format the eMMC and TF cards. Please save important files before formatting. Default Set: All functions are reset to the factory state. Version: It show the model number and software version.
PART

APP0100km/h0-400mGPS0100km/h400m (GPS3″Ready” 100km/h400m “Ready” 1.0-100km/h0-400m 3 2. 33 0-100km/h0-400m 3.55 APP APP
1. “”””APP 2.1,GPS2, “”3 3.GPSGPS

Tilt Angle

Straight racing functions has three modes: Racing video mode, Racing mode and OFF state. Racing video mode: The default mode is racing video mode (racing data is written into video which can be brought up and composited in APP).It is divided into two modes: – km/h and – m to record the speed-up time from – km/h and the riding time of m distance(Only on the state of GPS is ON and minutes loop recording mode). After selecting the mode in straight racing interface, press”OK”to start (GPS signal should be good),countdown seconds,”Ready”will be showed in main host screen. racer is ready to start. The timing starts at the departure moment (vehicle speed is zero), according to the selected mode, when the speed is increased to km/h or raced to m, the timing ends. This process timing is one record. Vehicle speed is km/h the main host screen will show”Ready”,you will enter the second round of racing. If you stop during the racing, the timing will restart at the next racing. One round finished the latest records will be displayed in the main host screen .Taking longer time record in red, shorter in green. Exiting the straight racing interface means exiting the racing mode. Note: ,In straight racing mode interface, long press UP/Down button to switch – km/h and – m.Long press for seconds can clear all racing date in main host screen.
,In racing vide mode, pres”s OK”the recording video will be cut and saved, then keep recording racing video. It is need to press”OK”again to restart after minutes video finished recording. If you don’t get minutes to switch to another racing mode (e.g. – km/h to – m), the video will also be cut and saved after pressing the confirm button, then the recording will start again.
,Up to race records can be kept in main host screen, and they will be cleared manually after races. Only clear the records which showed in main host screen display, the racing data of the recorded video can be brought up in APP. Racing mode: Racing data is not written into the video, and relevant data cannot be retrieved in APP. The operation method is the same as the racing video mode, but the video will not be cut off. This mode does not interfere with video recording. OFF state: When you choose to off this mode, the straight racing function is turned off, and the straight racing interface is no longer displayed in the main host screen, only the video interface and the data interface are displayed.
Troubleshooting .The racing interface does not show or the speed video cannot add watermark: Please check the status of
the straight racing function in the main host setting interface, if it is “OFF”, the racing interface will not be shown. If it is in “Racing mode”, the racing data will not be written in the video, and the speed watermark cannot be added in the APP.
.The straight racing function can not running: ,Please make sure the GPS is”ON”and the signal is good , Please check the status of the straight racing function in the main host settings interface, if it is in”Racing video mode”, please adjust the video cycling time to minutes.
.The speed suddenly drops to zero during the racing: It may be due to local GPS signal instability or interfered, please try again in an open area with good GPS signal.
PART

° OK “”OK
Tilt angle : When motorcycle leaning left/right while riding, the current angle (max. angle is °) and real-time speed will displayed, the max. tilt angle and real-time vehicle speed at the max angle will be recorded. Tilt Angle Correction: ,During installation, please ensure that the angle between the main host and the horizontal plane is within degrees and keep parallel to the front instrument as far as possible. If it is beyond the range, tilt angle data may cause data deviation. Make sure motorcycle is on flat ground, keep the motorcycle with the ground at degree and the handlebar upright to ensure motorcycle wheels in a straight line.
, Long press”OK”button seconds, will appear an operation menu, press”UP/Down”button to select”Tilt angle correction”, short press”OK”button to confirm.
Remote control matching

Ground level

0
96
MAX
42

REC
102
MAX
39
“OK”

PART

/Indicator light
Camera button
Switch key
Video lock

Setup

WIFI
WIFI

/

Date/Time Auto Matching TirePressure

TemperatureScreen Off Delay Beep Sound Image Rotation

Note: wireless remote control is optional equipment, please purchase it separately if necessary. Lease refer to the remote control manual for detailed operation.

HM .HM “”””””
“””···” .””””K
“”
HM and Wireless Remote Control Matching Operation . Short press the”OK”button on HM to pause recording. Short press”Setting”twice to enter
system settings interface, select”Auto Matching”and confirm. . Simultaneously press and hold the”Camera”&”Video Lock”on the remote control. After the K
remote control indicator flashes times, the matching is successful with words”Matching sucess” and the main screen will return to system settings interface .If not work, please try again.
4

Tire Pressure

PART

Setup

WIFI
WIFI

/

Date/Time Auto Matching TirePressure

TemperatureScreen Off Delay Beep Sound Image Rotation

Setup

Matching

Tire Pressure Maininter face Switch Setting

Tire Pressure Limit Setting

Tire Pressure Abnormality Alert Switch Setting

Setup

Front Wheel Matching

Rear WheelMatching

HM .HM “””””
“””””” “”···”
./ “” 1.20
.
“” “FW””” “RW” “” “” “” ” “15 “” 15″” 15

HM and Tire pressure detector Matching Operation
. Short press the”OK”button on HM to pause recording. Short press”Setting”twice to enter system settings interface, select the “matching” option within the tire pressure, select “front wheel matching” or “rear wheel matching” and confirm. The screen will display “front wheel matching (rear wheel matching)··”.
. Screw the tire pressure monitor onto the corresponding (front/rear) tire nozzle until it is tightened. After successful pairing, the host screen will display “Front wheel matching successful (rear wheel matching successful)”.
Note: . Each tire pressure matching requires a second interval; If pairing timeout occurs, please repeat the above operation.
Matching: Paired with tire pressure monitors, after successful “front wheel matching”, the corresponding tire pressure value will be displayed on the tire pressure display interface “FW”; After the “rear wheel matching” is successful, the corresponding tire pressure value will be displayed on the tire pressure display interface “RW”.
Tire Pressure Maininter face Switch Setting: After being turned on, the host screen displays the “tire pressure display interface”; After shutdown, the “tire pressure display interface” will not be displayed on the host, but will default to closed. After matching with the tire pressure monitor, the “tire pressure display interface” will automatically open. If the host does not match the tire pressure monitor, it will not be able to provide data normally.
Tire pressure limit setting: used to set the alarm values for the highest and lowest tire pressures. After setting the maximum and lowest front tire pressure limits, when the tire pressure is greater than or equal to the set limit, when the front tire pressure is lower than or equal to the set limit, when the rear tire pressure is higher than or equal to the set limit, and when the rear tire pressure is lower than or equal to the set limit, the host screen will display “Abnormal tire pressure, please check the tires as soon as possible” Prompt box accompanied by beeping sound (lasting for seconds).
Tire Pressure Abnormality Alert Switch Setting: After being turned on, when the tire pressure limit is set above or below the set value, the host screen will display a “Tire pressure abnormal, please check the tires as soon as possible” prompt box accompanied by a beep sound (lasting for seconds); When the tire pressure is lost, the host screen will display a “tire pressure device lost” prompt box accompanied by a beep sound (lasting for seconds), which defaults to off. After matching with the tire pressure monitor, the tire pressure alarm will automatically turn on. If the host does not match the tire pressure monitor, it will not be able to alarm.

APP APP operation

HM APP

1.HM 0 P SSIDXX-XXXXXPWA2: 00000000

2.”HM -xxxx”WiFi 80HFKAPP “WiFi”

HM APP connection

.Long press”Setting”while recording, main screen will

be in blue and show: SSIDXX-XXXXXPWA :

.

.Select the name of WIFI”HM -xxxx”on your phone

to connect, initial password is:

, then turn on

HFK APP, it will connect successfully, the main screen

will show”WIFI connection successful”.

/Video
1920*1080
00:00:10

Android
“””eMMC/TF””eMMC” TF”TF””” APP””
Android Download
Select”Folder”enter in”eMMC/TF Folder”(default in “eMMC”, if insert a TF card, it can switch to”TF”), download the file. Or you can download the file directly in preview. Then back to phone”Files”to check the downloaded files.

File
–
123MB
–
225MB

-xxxx -xxxx

Edit Phone Folder eMMC/TF eMMC/TF Folder
Download
Edited Folder
Picture
Video

–
12.4MB
–
32MB
–
9.3MB

-xxxx -xxxx -xxxx

eMMC/TF eMMC/TF Folder Picture
Edited Folder
Video

2024 -0110-xxxx
223MB
2024-0109-xxxx
92MB

File
–
19.3MB
–
9.23MB

-xxxx -xxxx

PART

Select video resolution / ON/OFF voice recording
Capture current picture
Switch view

/Camera
12M

Select picture resolution

/ Start/stop recording

Photo

APP Scan QR code and download App (Android/IOS)

Phone Folder
Edit
Download Locked Video

–
23MB
–
92.3MB
–
153MB

-xxxx -xxxx -xxxx

Unlock

“””eMMC/TF”” ” “”
Unlock the locked videos
Select “Folder” enter in “eMMC/TF Folder”, click”Edit”to choose the files which need to unlock.

Share

iOS
IOS .”””eMMC/TF””eMM
C”TF”TF””” 2.”” “””” “”APP” ”
.”” WIFI

IOS Download ,Select”Folder”enter in”eMMC/TF Folder”(default in
“eMMC”, if insert a TF card, it can switch to”TF”), download the file you need, and also can download the file directly in preview
,Select”Phone Folder”,you can view the downloaded files on your phone. Select “Share”to”Save the video” or”Save the Photo”.Then back to phone”Photos”to check the downloaded files.
.Edited videos saved in”Edited Folder”, they can be shared directly to social media(Keep phone on line, if cannot share, please disconnect the WIFI between phone and DVR). They also can download to the phone folder, same operation as above.

Video Clip Add Watermark
Trajectory

15

00:00

00:15

Play

0-100km/h

6.71s

N 22° 32 42 E 114° 03 10
KM/H

60°

/Compass mark Straight Racing mark /Map mark /Tilt Angle mark /LAL mark /Speed mark
5

.”””eMMC/TF” “”
.”” “”””
Video Clip&Add watermark
.Select”Folder”enter in”eMMC/TF Folder”, download the file you needed(also can download in preview).
.Select”Phone Folder”,find the downloaded file, play the video and click”Video Clip”or”Add watermark”to edit the file.

” ” ” “””” ” “”
Video Clip
Drag the progress bar in the video, select you needed part. Click”Play”to preview the selected video clip, click “Done”to finish. Drag the sliders at both ends of the video to reduce the video time. The clipped video files will be stored in the”Edited Folder”.

Troubleshooting

.””””””””””””
.
3.”””” Add watermark
.Click the”Straight Racing mark”/”Speed mark”/”Longitude & latitude mark”/”Compass mark”/”Map mark”or”Tilt Angle mark”button on the screen to add or cancel the mark.
.Drag the mark and place it in the appropriate position. . Click the”Start”button to start the video composition. The synthesized ones will be stored in the “Edited Folder”.
PART

GB TF

10 3 Mb/s,

Mb/sTF

.

.

. //TFTF

TFTFTF

. R

RR

. R

.

.

.

. .

. WIFIWIFIWIFISSID: XX-XXXXX

PWA :

( )WIFIWIFI.

WIFI

. RESET

. ,

R ,

Note: This system max support for 512GB TF card. In order to make sure video recording normally, we suggest to use brand TF card. Because the recording system keep reading and writing data, so please must be use high speed 10 3 TF card or above (reading speed of 100Mb/s,writing speed of 60Mb/s). When the DVR is working, please do not remove the TF card, it may cause the TF card damaged.
1.After start on the motorcycle but the DVR cannot turn on, first check power connection if normal.
2.Press “ON” button but DVR cannot turn on, please check the power connection if normal.
3.If DVR cannot recording/take pictures/lock videos, please check if you inserted the TF card or need to format TF card. If the problem is still on after formatting the TF card, please re-insert the TF card or reformat or replace a new card.
4.Main host “F”-front camera(“B”-rear camera) has no display image, please switch front(or rear)
camera to check. For example: Front camera has no image, switch “F” to “B”, but “B” still no display, then make sure “F” camera with problem, please change a new one.
5.”F” and “B” both have no display image, check the cameras connection if right.
6.If the video comes blurry, please check the lens if with dust, and wipe them clean.
7.If the recording video has no voice, please check the microphone if “ON”.
8.During normal riding when you find videos locked: Please adjust the G-sensor sensitivity. The default is
integrated general road, please select to Bumpy mode.
9.Motorcycle Collision but recording video unlocked: Please check if the G-sensor is “ON”, if it is on, please set the sensitivity mode in Urban road.
10.WIFI connection is abnormal: Check the WIFI if “ON”.After connecting WIFI, the display will show: “SSID: XX-XXXXX. PWA2:00000000″(Initial password is 00000000).Connecting WIFI the screen display is in blue with words”WIFI connected”.When connecting WIFI please turn off the cellphone Bluetooth.
11.If the DVR crashed, please press “RESET” and try again.
12.Display screen or recording video if have stray electromagnetic interference or purple-grained electromagnetic interference: 1, Please check the motorcycle spark plug model, please use R-rated resistive spark plug. 2, Check if there has any problem with the cable lines or binding of the cameras. Please straighten the cable don’t fold them up and keep a certain margin. Do not tie them too hard or squeeze too tightly with the motorcycle shell.

FCC STATEMENT

PART 10

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, Pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

6

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>