LOGIC TW10 Wireless Headphones User Guide
- June 16, 2024
- Logic
Table of Contents
LOGIC TW10 Wireless Headphones
Thank you for purchasing the LOGIC TW10. Please read this manual carefully before using this product. Please be sure to keep this manual for future reference.
Function Introduction
The TW10 True Wireless Headset, features wireless Bluetooth audio reception, Bluetooth playback, wireless transmission of lossless music, no delay, long- lasting battery life, Bluetooth 5.0 chip with low power consumption, hands- free answering, 5h playback, and other functions and applications.
Precautions
- For best performance please DO NOT use the product in extreme temperatures such as hot, cold, dusty, and humid environments.
- DO NOT drop, impact, or vibrate the product when in use
- Appropriate ventilation should be maintained around the product. Otherwise, it would easily cause the temperature inside the cradle to rise and eventually damage the circuit.
- When moving the product, first turn it OFF and disconnect the corresponding cable from other devices.
- The surface of the product and its loudspeakers should avoid corrosive liquids and gases. The product should not be placed in direct sunlight for a long period.
- In case of dust, clean it regularly with a clean soft cloth. If it is stained, wipe it with a detergent that does not contain a fortifier.
- DO NOT press hard ON the switch and other components.
- If the machine suddenly emits smoke or any other abnormal phenomenon occurs, please turn OFF the device and quickly unplug it to avoid accidents.
- DO NOT disassemble the unit to avoid danger.
Warning:
- This product must NOT be exposed in areas such as direct sunlight, fire, or similar overheating environments!
- Note: All the diagrams are for reference only. Please refer to the actual product.
Key and Interface Diagram
Learn about the components of the TW10 True Wireless Headset
Directions for Use
- Charging box indicator: The red light is always ON when the device is charging and is OFF when the charge is completed.
- Micro USB port: The Micro USB port can be connected to charge the machine.
- Charging box: The two earphones can be put in the charging box simultaneously for automatic charging.
- Open the box to automatically pair nearby devices.
Touch button
- a. ON: When the earphone is “OFF”, place the earphone in your ear and press the touch button of the earphone for 5 seconds until you hear the “Power ON” indication, the device will enter into a pairing state automatically and the blue indicator will flash 3 times. The pairing time is 180 seconds. If the pairing time is out, the earphone will automatically turn OFF, accompanied by a “Power OFF” indication. When the earphone is taken out from the charging box, it will automatically turn ON, pair up, and connect to the mobile phone (the mobile phone must have been paired before).
- b. OFF : Press and hold the touch button for 5 seconds until you hear the “Power OFF” indication, the red indicator will flash 3 times and then go out; after the earphone is placed in the charging box, it will automatically turn OFF.
- c. Pairing connection: After the main and secondary earphones are connected, the main earphone will enter the mobile phone pairing state, and the red and blue indicators will alternately flash, place the earphone in your ear, use the mobile phone to search for the earphone, find the Bluetooth device in the mobile phone interface, click to connect, if successful you will hear the Connected” indication; the blue indicator will flash once in 3 seconds after connection.
- d. Disconnect: You’ll hear a “Disconnected” indication and the device will automatically turn OFF after 3 minutes of no connection.
- e. Hang up the phone: During the call, you may end the call by pressing the touch button once.
- f. Reject the call : When receiving a phone call press the touch button for about 2 seconds to reject.
- g. Answer the call: When receiving a phone call, press the touch button once to answer.
- h. Automatic connection at power ON: Each time the earphone is turned ON, it will automatically initiate a connection to the mobile phone that it previously paired with.
- i. Music play/Pause: In the music playing state, click the touch button once to pause, and repeat the operation to play.
- j. Previous/Next: In the music playing state, click the touch button twice for the next song, and click the touch button 3 times for the previous song.
- k. Factory setting: Press and hold the touch button for 10 seconds to clear the pairing record of TWS in the state.
- In the OFF state, press and hold the touch button for 20 seconds to clear all pairing records.
- I. Turn ON/OFF the voice control : Press and hold the touch button for about 1 second and release, there will be a “Beep” tone to summon the voice function. m. Single ear mode: When the second earphone is out of power, the main earphone with power can continue to be used normally.
Earphone Indicator:
- a. Airo Stereo pairing mode: The red and blue indicators will flash at the same time for about 3 minutes.
- After 3 minutes, the pairing time will be out automatically, and the earphone will turn OFF.
- b. OFF: The red indicator will flash 3 times.
- c. Connected standby: The blue indicator will flash once every 3 seconds.
- d. In the call: The blue indicator will flash once every 3 seconds.
- e. Playing music: The blue indicator will flash once every 3 seconds.
- f. Charging completed: The red indicator will be OFF.
- g. Charging: The red indicator will be always ON.
- h. Low battery alarm: When the battery is lower than 3.2V, the red LED will flash once every 5 seconds, accompanied by a “Low Battery” tone every minute.
- Microphone: Hands-free calling is available after connecting with the mobile phone in Bluetooth state.
- Charging Pin: The earphones will automatically start charging, once placed inside into the charging box.
Technical Parameters
- Bluetooth Protocol: A2DP, AVRCP, HFP, HSP
- Bluetooth Chip: REALTEK RTL8763BFR V5.0
- Working Hours: 12h (Earphone + Charging Box)
- Charging Time: 2h (Earphone)
- Rated Input: DC 5V 55mA (Earphone) DC 5V 400mA (Charging Box)
- Sensitivity (SPL): -38$1dB
- Voice Function: Call Support, Voice Status Indications
- Working Frequency Band: 2.4g ISM Band (2.402 – 2.480ghz)
- Frequency Response Range: 20Hz – 20kHz
- Microphone: Goertek S150B381-055
- Distance: 10m-15m
- Speaker Size: 6mm
- Distortion Rate: 1%
- Earphone Weight: About 0.6g
- Speaker Material: Graphene Vibrating Film
- Noise Reduction: CVC6.0
- Impedance: 160
FCC Statement
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, according to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used under the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
SAR Information Statement
Your wireless phone is a radio transmitter and receiver. It is designed and
manufactured not to exceed the emission limits for exposure to radio frequency
(RF) energy set by the Federal Communications Commission of the U.S.
Government. These limits are part of comprehensive guidelines and establish
permitted levels of RF energy for the general population. The guidelines are
based on standards that were developed by independent scientific organizations
through periodic and thorough evaluation of scientific studies. The standards
include a substantial safety margin designed to assure the safety of all
persons, regardless of age and health. The exposure standard for wireless
mobile phones employs a unit of measurement known as the Specific Absorption
Rate or SAR. The SAR limit set by the FCC is 1.6 W/kg Tests for SAR are
conducted with the phone transmitting at its highest certified power level in
all tested frequency bands. Although the SAR is determined at the highest
certified power level, the actual SAR level of the phone while operating can
be well below the maximum value. This is because the phone is designed to
operate at multiple power levels to use only the power required to reach the
network. In general, the closer you are to a wireless base station antenna,
the lower the power output. Before a phone model is available for sale to the
public, it must be tested and certified to the FCC that it does not exceed the
limit established by the government adopted requirement for safe exposure. The
tests are performed in positions and locations (e.g., at the ear and worn on
the body) as required by the FCC for each model. The highest SAR value for
this model phone when tested for use at the ear is 0.396W/Kg and when worn on
the body, as described in this user guide, is 0.472W/Kg(Body-worn measurements
differ among phone models, depending upon available accessories and FCC
requirements). The maximum scaled SAR in hotspot mode is 0.498W/Kg. While
there may be differences between the SAR levels of various phones and at
various positions, they all meet the government requirement for safe exposure.
The FCC has granted Equipment Authorization for this model phone with all
reported SAR levels evaluated as in compliance with the FCC Exposure
guidelines. SAR information on this model phone is on file with the FCC and
can be found under the Display Grant section of
http://www.fcc.gov/oet/fccid.
FCC ID: 055W4719 Additional information on Specific Absorption Rates
(SAR) can be found on the Cellular Telecommunications Industry Association
(CTIA) website at http://www.wow-com.com.
In the United States and Canada, the SAR limit for mobile phones used by the
public is 1.6 watts/kg (W/kg) averaging over one gram of tissue.
The standard incorporates a substantial margin of safety to give additional
protection for the public and to account for any variations in measurements.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF
exposure requirements, a minimum separation distance of 10mm must be
maintained between the user’s body and the handset, including the antenna.
Third-party belt clips, holsters, and similar accessories used by this device
should not contain any metallic components. Body-worn accessories that do not
meet these requirements may not comply with RF exposure requirements and
should be avoided. Use only the supplied or approved antenna.
Warranty Certificate
Terms and Conditions
- LOGIC warrants that their Products will be free from defects in material and workmanship.
- The warranty period is one (1) year for the products and three (3) months for the accessories that are part of the original package including the battery.
- The warranty period begins on the date of purchase by the End-User who shall present an invoice or a purchase receipt when requiring warranty service otherwise the warranty period will begin from the date of manufacture of the product.
- LOGIC will repair a product without cost to the customer if it presents a manufacturing defect or defect in workmanship during the warranty period and if the defect occurred under normal conditions of use per the instructions and specifications stated in the user’s manual.
- For additional information about the terms and conditions of LOGIC’s Limited Warranty or to obtain warranty service information, please visit the support section at: logicmobility.com
- logicmobility.com
- Made in China
- Copyright Swagtek, Inc. 2022
Documents / Resources
|
LOGIC TW10 Wireless
Headphones
[pdf] User Guide
TW10 Wireless Headphones, TW10, Wireless Headphones, Headphones
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>