v LOGiC V5-NBT-PNP BMW With Navigation System Or Radio User Manual
- May 15, 2024
- v LOGiC
Table of Contents
v LOGiC V5-NBT-PNP BMW With Navigation System Or Radio
Specifications
- Product Name: V5-NBT-PNP
- Compatibility: F-series BMW with a navigation system or radio and 6.5, 7, 8.8, or 10.25 monitor with 4+2pin HSD2 LVDS connector
- Version: 30.03.2023
Legal Information
By law, watching moving pictures while driving is prohibited, the driver must
not be distracted. We do not accept any liability for material damage or
personal injury resulting, directly or indirectly, from the installation or
operation of this product. This product should only be used while standing or
to display fixed menus or rear-view-camera video when the vehicle is moving,
for example, the MP3 menu for DVD upgrades.
Changes/updates of the vehicle’s software can cause malfunctions in the interface. We offer free software updates for our interfaces for one year after purchase. To receive a free update, the interface must be sent in at its own cost. Labour costs and other expenses involved with the software updates will not be refunded.
Product features
- Own on-screen display and setup
- Rear-view camera input
- Automatic switching to rear-view camera input on the engagement of reverse gear from all operation modes
- Front camera input / SMART-LINK input
- Control of SMART-LINK module over iDrive control panel
- Manual switching to rear-view camera (only for vehicles with PDC button)
- Manual return from rear-view and front camera (cancellation of automatic switching)
- 2 trigger outputs (+12V max. 1A), separately adjustable switching events (CAN, ACC, camera, reverse gear)
- Picture-in-picture mode combining after-market rear-view and front camera picture(s) with factory parking sensor graphics
- Interactive lane lines
- Compatible with all factory video accessories (e.g. rear-view camera, Top-View, night vision, DVD-changer, TV tuner)
- USB update port for software updates by consumer
Before installation
Read the manual before installation. Technical knowledge is necessary for installation. The place of installation must be free of moisture and away from heat sources.
Check the compatibility of the vehicle and accessories
Check compatibility of vehicle and accessories
Setting the DIP switches of the interface box V5C-M637
DIP 1 and 2 on the back of the interface box V5C-M637 are used to set the
monitor type. The default setting is:
After each change of the DIP switch settings, you have to execute a power reset of the interface-box!
LED‘s of the interface-box V5C-M637
Connection schema
Installation
- Switch off the ignition and disconnect the vehicle’s battery! The interface needs a permanent 12V source. If according to factory rules disconnecting the battery is to be avoided, it is usually sufficient to put the vehicle in sleep mode. In case the sleep mode does not show success, disconnect the battery with a resistor lead.
- If the power source is not taken directly from the battery, the connection has to be checked for being start-up-proven and permanent.
- Before wire and device installation, we suggest connecting and testing the correct function of all after-market and factory infotainment equipment!
The interface is installed on the backside of the head unit.
Connecting interface-box and harnesses
- Remove the female Quadlock connector of the vehicle harness from the rear of the navigation computer.
- Remove optical leads from the female Quadlock connector of the vehicle harness and insert them into the female Quadlock connector of harness TV-BM01 at the same position.
- Connect the female Quadlock connector of the vehicle harness to the male Quadlockconnector of harness TV-BM01.
- Connect the female Quadlock connector of harness TV-BM01 to the male Quadlockconnector of the navigation computer
- Connect the female 8-pin Molex connector of the harness TV-BM01 to the male 8-pin molex connector of the harness TV-BM01.
- Connect the female 12-pin AMP connector of the harness TV-BM01 to the front site of the V5C-M637 interface box.
Special case BMW i3
Since the BMW i3 has the head unit under the rear seat, the extension cable
V5C-CON300 must be purchased separately. This is inserted between the TV-BM01
and the V5C-UNI01 cable set
- Connect the female 4+2pin HSD2 LVDS connector of the LVDS cable CAB-HSD2-RR148 to the male 4+2pin HSD2 LVDS connector (LVDS-OUT) on the front of the interface-box V5C-M637.
- Remove the female 4+2pin HSD2 LVDS connector of the vehicle harness of the factory monitor and connect it to the male 4+2pin HSD2 LVDS connector (LVDS-IN) on the front of the interface-box V5C-M637.
- Connect the second female 4+2pin HSD2 LVDS connector of the LVDS cable CAB-HSD2-RR148 to the male 4+2pin HSD2 LVDS connector of the factory monitor.
After-market front camera
Connection to the after-market front camera
- Connect the video RCA of the after-market front camera to the female RCA connector “FRONT CAM” of the interface box V5C-M637.
- The pink wire of harness V5C-UNI01 can be used for the +12V electric power supply (max. 1A) of the after-market front camera. Configure in the OSD menu “OPTION”, menu item “POWER OUT 1” the designated electric power supply (see chapter “Configurable switching outputs”). ****
Settings for connecting an after-market front camera
You have to configure some settings in the OSD-menus INPUT and OPTION if you
want to connect an after-market front camera (Operation of the OSD: see
chapter “OSD-Operation”).
Note: You can deactivate the enabled parking process by pressing the iDrive or by enabling other modes (e.g. radio). After deactivation you can’t enable the parking process again until the vehicle is diving faster than 20km/h, the ignition is switched off and on or the PDC will be disabled and enabled again, if existing
After-market rear-view camera
Connection to the after-market rear-view camera
- Connect the video RCA of the after-market rear-view camera to the female RCA connector “REAR CAM” of the interface box V5C-M637.
- The green wire of harness TV-BM01 can be used for a +12V electric power supply (max. 1A) of the aftermarket rear-view camera. Configure in the OSD menu “OPTION”, menu item “POWER OUT 2” the designated electric power supply (see chapter “Configurable switching outputs”).
Settings for connecting an after-market front camera
You have to configure some settings in the OSD-menus INPUT and OPTION if you
want to connect an after-market front camera (Operation of the OSD: see
chapter “OSD-Operation”).
Note: You can deactivate the enabled parking process by pressing the iDrive or by enabling other modes (e.g. radio). After deactivation you can’t enable the parking process again until the vehicle is diving faster than 20km/h, the ignition is switched off and on or the PDC will be disabled and enabled again, if existing.
SMART-LINK
The front camera input can alternatively be used for a SMART-LINK set
(CarPlay® & Android Auto® module) connection. In addition, the interface has
the option of controlling the connected SMART-LINK module over the iDrive
control panel.
SMART-LINK video and control connection
- Connect the video RCA of the SMART-LINK module to the female RCA connector “FRONT CAM” of the interface box V5C-M637.
- Connect the pink cable (+12V Power OUT 1) of the V5C-UNI01 harness to the +12V ACC power input of the SMART-LINK module. Configure in the OSD-menu “OPTION”, menu item “Power Out 1” the setting “CAN” (see also chapter “Configurable switching outputs”).
- Connect the SMART-LINK interface control port “STA-UART” (available separately) to the “SMART-LINK CarPlay® Android Auto®” socket of the V5C-UNI01 harness..
SMART-LINK audio connection
- By using an audio cable (sold separately), connect the audio output of the SMART-LINK module to the vehicle AUX input.
Settings for SMART-LINK connecting
You have to configure some settings in the OSD-menu INPUT if you want to
connect the SMART-LINK module (Operation of the OSD: see chapter “OSD-
Operation”).
Configurable trigger outputs
- You can configure both +12V trigger outputs separately. The pink wire is POWER OUT 1 and the green wire is POWER OUT 2.
Note : You can configure both trigger outputs in the OSD-menu OPTION separately (Operation of the OSD: see chapter “OSD-Operation”).
Interactive lane lines
You have to configure some settings in the OSD-menu OPTION if you want to
activate interactive lane lines (Operation of the OSD: see chapter “OSD-
Operation”).
Note : ”PDC – picture in picture” and “interactive lane lines” functions are not simultaneously usable.
Picture settings
- The picture settings and picture format can be changed in the OSD menu (activation is only possible from the camera or SMART-LINK level by long pressing the OPTION -button).
The following options are available:
- Brightness
- Contrast
- Saturation
- Hue
- Sharpness
- Format =
8.8” and 10.2” 24:10 ultrawide monitor:
- FULL = 24:10 video full-screen mode
- ZOOM = 24:10 video full-screen mode zoom
- AV+LVDS = 16:9 video on left side, factory picture on right side
6.5” and 7” 16:9 monitor:
- FULL = 16:9 video full-screen mode
- ZOOM = 16:9 video full-screen mode – zoom
Operation
OSD – On-screen display
You can change the basic configurations of the interface in the OSD (on-screen
display).
OSD – Operation
You can control the OSD by iDrive.
iDrive High
iDrive Low
iDrive selection
OSD menu „OPTION“ – „IDRIVE“ is for setting the right iDrive control knob.
OSD – Additional setting options
The following settings in the OSD-menus OPTION and OSD can be configured over
and above the described settings in this manual (Operation of the OSD: see
chapter “OSD-Operation”):
Video-in-motion function
It is possible to activate and deactivate the video-in-motion in the OSD menu
“OPTION” (Operation of the OSD: see chapter “OSD-Operation”).
Selecting the interface as current video-source
- In the vehicle’s CD/Multimedia > External devices menu, activate AUX front by iDrive and after it long press the MEDIA button respectively long-press the AUDIO button to choose the interface as the current video source.
- Short press the MEDIA button respectively AUDIO button to switch the video inputs. Each short press will switch to the next enabled input. If all inputs are enabled the order is:
- RVC à FVC/SmartPhone à…
- Inputs that are not enabled are skipped.
- The exiting of the video interface level is achieved by a long press of the MEDIA / AUDIO button or a short press of the RADIO / MENU / TEL / NAV button.
Note: Activation of the AUX level is not necessary for camera view.
Controlling of the connected SMART-LINK module
The picture shows which functions of the connected SMART-LINK module can be
executed by iDrive control panel. Once the FVC/SmartPhone input is activated
the iDrive control panel action will execute the function described in the
picture.
Controlling by iDrive High
Controlling by iDrive Low
Specifications
- Operation voltage: 10.5 – 14.8V DC
- Stand-by power drain: <0,1mA
- Operation power drain : 190mA
- Power consumption: 2,6W
- Temperature range: -20°C to +80°C
- Weight (box only): 208g
Measurements (box only) В x H × T 103 × 30 × 105 mm
Connections (interface-box)
Technical Support
- Car audio-Systems Vertriebs GmbH manufacturer/distribution
- In den Fuchslöchern 3
- D-67240 Bobenheim-Roxheimemail support@caraudio-systems.de
FAQ
Frequently Asked Questions
- Q: Is it safe to use this product while driving?
- A: By law, watching moving pictures while driving is prohibited. This product should only be used while standing or to display fixed menus or rear-view camera video when the vehicle is moving.
- Q: How can I receive software updates for the interface?
- A: We offer free software updates for our interfaces for one year after purchase. To receive a free update, the interface must be sent in at your own cost.
Legal Disclaimer: The mentioned company and trademarks, as well as product names/codes are registered trademarks ® of their corresponding legal owner
Version 30.03.2023
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>