SKINXTC SculptX 0.3Hz Worldwide Skincare Instruction Manual

: June 16, 2024
: SKINXTC

Table of Contents

SculptX Microcurrent Device
Charging SculptX
SculptX Instructions
SculptX Get Started
SculptX Steps
SculptX Precautions
SculptX Specifications
SculptX Frequency of Use
Contraindications
SKIN XTC™ Worldwide
CUSTOMER SERVICES
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SKINXTC SculptX 0.3Hz Worldwide Skincare

SculptX Microcurrent Device

Charging SculptX

Ensure to charge SculptX for an initial full 3 hours, before switching on.
Blue lights will flash when SculptX is charging.
LIFT must be switched off before charging.
Type C USB charge cable is used for SculptX.
Charge your SculptX once each week.
Always switch off SculptX before charging (do not use device while on charge).
Charging is complete when the blue lights stop flashing, (bar the initial 3 hour charge).

SculptX Instructions

Switch on SculptX with one quick press of the power button.
Change SculptX level intensity from level 1 to 5 by pressing the power button.
Number of blue lights on your SculptX device represent the level selected.
Red LED light therapy is programmed to come into use when you switch on SculptX .
Press the power button for 2 seconds to turn off red LED light therapy, (repeat to switch on).
SculptX is programmed to switch off after 5 minutes to prompt you treat a different section of the face or neck.
Press the power button and hold for 3 seconds to switch off SculptX.

SculptX Get Started

Divide the face into four sections when doing a full face treatment.
Under the eyes marks the vertical halfway point.
Apply adequate water based gel for conductivity of microcurrent energy.
Spray water to stop the area from drying out and to ensure maximum results are achieved.

SculptX Steps

Wash face with oil free cleanser and pat dry
Apply water based conductive gel or water based serum to the area of face for treatment.
Switch on SculptX with the power button and select your level of microcurrent intensity indicated by number of blue lights.
Every 5 seconds a beep will sound to indicate to move to the next pass. It’s recommended to do 3 passes to one area.
Use a combination of glide passes with lift and hold techniques.
Spritz water on face to prevent skin from drying out and to 1maintain high conductivity levels of microcurrent energy.
Repeat to all areas working from the neck to the forehead.
Clean SculptX with a dry micro-fibre cloth.

SculptX Precautions

Do not use on the upper eyelids, eyeballs, around the ears, or over the thyroid area.
Do not treat inner eye orbital bone areas that surround the eye.
Do not use on the mucosa which is a membrane that lines cavities of the body.
Do not submerse under water. The device is not waterproof.

SculptX Specifications

Parameter	Specification
Power	800mAh (milliamps)
Frequency	0.3Hz
Max depth Red LED light	650nm (nanometers)
USB recharge cable	Type C
Box dimensions Total Weight	L 14cm x W 14cm x H 5cm 300 grams

Microcurrent amps (aU) Level 1
Level 2
Level 3
Level 4
Level 5| __ 400 aU
500 au
600 aU
700 aU
800 aU

SculptX Frequency of Use

Duration per treatment	Week 1 – 6	Week 6+
20 minutes	5 treatments per week
20 minutes		4 treatments per week

Contraindications

Do not use if you have any of the following, but not limited to,

Heart disease, abnormal blood pressure, malignant tumours, cancer
Migraines
Seizures or Epilepsy
Heart issues, i.e.: have a pacemaker in your body
Currently undergoing dental treatment
Dermatitis, psoriasis, or other skin disease (consult with dermatologist)
Had recent chemical peels or similar salon treatments within 2 weeks
Had Botox or filler within 2 weeks
If unsure consult with your medical practitioner for further advice.

SKIN XTC™ Worldwide

CUSTOMER SERVICES

info@skinxtc.com
www.skinxtc.com
Facebook Group: SKIN XTC
Instagram: skin_xtc
Twitter: @skin_xtc
TikTok: @skinxtc
F acebook: SKIN XTC