Godox LiteFlow K1 Cine Lighting Reflector Instruction Manual

Godox LiteFlow K1 Cine Lighting Reflector Instruction Manual

Foreword

Thank you for purchasing!
Introducing the innovative and unique lighting diffusion system by Godox – the Cine Lighting Reflector. With its precision-designed reflector, this cutting- edge system accurately guides the light source to the desired lighting positions, allowing for precise control over the scattering of light while minimizing reliance on flags or frames on the set. What’s truly astonishing is the meticulously crafted aluminum coating surface, which boasts only 3% light loss and 100% color accuracy. The reflector is available in four different sizes to accommodate various lighting requirements: 2.75″ × 2.75″, 5.91″ × 5.91″, 9.84″ × 9.84″, 19.69″ × 19.69″

DIFF 1(Blue color): Hard ray of light(diffusion rate is 13.2%)
DIFF 2(Yellow color): Medium soft ray of light(diffusion rate is 52%)
DIFF 3(Green color): Soft ray of light(diffusion rate is 95%)
DIFF 4(Red color): Soft strip ray of light(diffusion rate is 94%)

The above data is provided by Godox laboratory.

Lighting Effects Display (Using LiteFlow 50 as an example)

DIFF 1（Blue color）

DIFF 2（Yellow color）

DIFF 3（Green color）

DIFF 4（Red color）

Cautions:

1. The reflector is prone to scratching. Please use specialized gloves when handling.
2. To ensure the reflector remains free from stains, it is recommended to clean it immediately after use. Failure to do so may result in difficulty cleaning the reflector if oil stains are left unattended for an extended period.
3. The reflector is prone to scratching, so handle with care during transportation or installation.

Name of Parts

1. Reflector
2. Slide Rail
3. Slot
4. Corner Guards
5. Safety Wire Hole

Cine Reflector Cleaning Instructions

1. Please wear gloves to clean during use
2. Spray an appropriate amount of cleaning solution evenly onto the surface of the reflector.
3. Let the cleaning solution sit for 15-30 seconds to thoroughly break down any oil stains.
4. Use a cleaning cloth to dry the reflective surface

Note: To ensure cleaning effectiveness, please do not reuse the cleaning cloth.

Installation of WMS / WMR

Depending on your requirements, you can install either the Wheel Mount Stud WMS or the Wheel Mount Receiver WMR.

The WMS features a 5/8″ male socket port. By installing WMS you can insert a connecting rod with a 5/8″ female socket.

The WMR features both vertical and horizontal female socket ports. By installing WMR you can insert a connecting rod with a male socket .

Installing WMS/WMR: To install WMS/WMR, loosen the wheel on the WMS slider by turning it counter-clockwise. Then insert it into the groove at the bottom of the reflector and slide it to the desired position. Once in position, turn the wheel clockwise to tighten and secure it in place.

What’s Inside LiteFlow K1

• Cine Lighting Reflector LiteFlow 7D1 × 1

• Cine Lighting Reflector LiteFlow 7D2 × 1

• Cine Lighting Reflector LiteFlow 7D3× 1

• Cine Lighting Reflector LiteFlow 7D4 × 1

• Cine Lighting Reflector LiteFlow 15D1 × 1
  

• Cine Lighting Reflector LiteFlow 15D2 × 1
  

• Cine Lighting Reflector LiteFlow 15D3× 1
  

• Cine Lighting Reflector LiteFlow 15D4 × 1
  

• Cine Lighting Reflector LiteFlow 25D1 ×
  

• Cine Lighting Reflector LiteFlow 25D2 × 1
  

• Cine Lighting Reflector LiteFlow 25D3× 1
  

• Cine Lighting Reflector LiteFlow 25D4 × 1
  

• Cine Lighting Reflector LiteFlow 50D1 × 1

• Cine Lighting Reflector LiteFlow 50D2 × 1

• Cine Lighting Reflector LiteFlow 50D3× 1

• Cine Lighting Reflector LiteFlow 50D4 × 1

• Cleaning Kit × 1

• Reflector Tool Kit × 2

• Soft Case SC17 × 1

Optional Accessories

• Wheel Mount Receiver(WMR)

• Wheel Mount Stud (WMS)

• Single Knob Gag GSK

• Dual Knob Gag GDK

• Multi-Adapter MA2R2S

• Flexible Arm AF30SS
  

• Flexible Arm AF40SS
  

• Flexible Arm AF30RS
  

• Flexible Arm AF40RS
  

• Flexible Arm AF20RC
  

• Ball-joint Arm AB30SS
  

• Ball-joint Arm AB30SS02

• Ball-joint Arm AB30SS03
  

• Rod Set RS25

• 

• Rod Set RS50
  

• Rod Set RS75
  

• Rod Set RS100
  

• Ball-joint Arm AB10RS

• Reflector Array Grip Kit GK7

• Reflector Array Grip Kit GK25

• Reflector Array Grip Kit GK50

• Soft Case SC13

• Soft Case SC14

• Soft Case SC15

• Soft Case SC16

• Soft Case SC17

• Flight Case FC03
  

Specification

1.43kg

Costumer Support

GODOX Photo Equipment Co.,Ltd.
Add.: Building 2, Yaochuan Industrial Zone，Tangwei Community, Fuhai Street, Bao’an District,
Shenzhen 518103,
China Tel: +86-755-29609320(8062)
Fax: +86-755-25723423
E-mail: godox@godox.com
godox.com
Made in China 705-LF0000-00

References

• GODOX Photo Equipment Co.,Ltd.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>