niko P47MR Presence Detector SnapFit for Flush Mounting Installation Guide
- June 16, 2024
- niko
Table of Contents
- niko P47MR Presence Detector SnapFit for Flush Mounting
- Product Information
- Product Usage Instructions
- FAQ
- Wiring
- Dimensions
- Installation
- App settings
- LED behaviour
- Specifications
- Detection area
- Troubleshooting
- Support & contact
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
niko P47MR Presence Detector SnapFit for Flush Mounting
Product Information
Specifications
- Article Number: 353-651321
- Configuration: DALI-2 master
- Input Voltage: Not specified
- Maximum Power Consumption: 0.5 W
- Circuit Breaker: Maximum MCB rating 16 A*
Product Usage Instructions
Mounting
The presence detector can be mounted using the SnapFit method. Follow the
steps below:
- Choose the desired location for mounting.
- Ensure the mounting surface is suitable and can support the detector.
- Snap the presence detector into place.
Installation
To install the presence detector, follow these steps:
- Connect the wiring according to the provided wiring scheme.
- If using a fixed ceiling, ensure that the product is not removable.
- If using a suspended ceiling, ensure that the product is removable.
- Secure the presence detector with a miniature circuit breaker (MCB) of maximum 16 A in the electrical cabinet. The MCB rating should comply with national installation rules.
Dimensions
The dimensions of the presence detector are as follows:
- a: 44 mm
- b: 9.5 mm
- c: 56.9 mm
- d: 10 – 12 mm
App Settings
Use the app settings to configure the presence detector according to your
preferences. The available settings include:
- Factory settings
- Switch ON/OFF
- 500 lux
- 15 min
- Detector tool
- LED behavior
Troubleshooting
If you encounter any issues with the presence detector, refer to the
following troubleshooting guide:
Problem | Possible Cause | Proposed Solution |
---|---|---|
Load does not turn on | The wiring is not correct | Check the wiring scheme |
Load does not turn off | The ambient light is too strong | Check the response |
value luminosity and raise the value if
necessary
App cannot connect to the detector| The switch-off delay is too long| Check
the switch-off delay and shorten the delay if
necessary
| The detector receives false triggers| Check for any objects that may cause
false triggering and
remove them from the detection range or lower the sensitivity
FAQ
-
What is the maximum MCB rating for the presence detector?
The maximum MCB rating for the presence detector is 16 A. -
What are the dimensions of the presence detector?
The dimensions of the presence detector are as follows:- a: 44 mm
- b: 9.5 mm
- c: 56.9 mm
- d: 10 – 12 mm
-
How should I mount the presence detector?
You can mount the presence detector using the SnapFit method.
Follow these steps:- Choose the desired location for mounting.
- Ensure the mounting surface is suitable and can support the detector.
- Snap the presence detector into place.
-
How do I troubleshoot issues with the presence detector?
If you encounter any issues with the presence detector, refer to the troubleshooting guide provided in the user manual. It provides solutions for common problems such as load not turning on or off, and app connectivity issues.
Wiring
This product must be secured with a miniature circuit breaker (MCB) of max. 16 A in the electrical cabinet. The MCB rating is limited by national installation rules.
Dimensions
Installation
App settings
LED behaviour
Specifications
- Article number 353-651321
- Configuration DALI-2 master
- Input voltage 230 Vac ± 10 %, 50 Hz
- Maximum power consumption 0.5 W
- Circuit breaker maximum MCB rating 16 A*
- Short circuit behaviour shutdown trigger voltage below 12 V, exceeding 1.3 s
- Short circuit behaviour restart period every 14 s until success
- Maximum voltage on the DALI bus 15 Vdc
- Maximum supply current 250 mA
- Maximum guaranteed current on the DALI bus 100 mA
- Detector output DALI Broadcast/DALI Adressable
- Maximum startup time DALI < 1200 ms
- Maximum PIR detection startup time 70 s
- Maximum number of control gear on the DALI bus 64
- Maximum number of dimmable zones 3
- Light intensity range 20 – 2000 lux, ∞
- Switch-off delay pulse, 20 s – 120 min, ∞
- Detection angle 360°
- Detection range (PIR) ø 12 m from a height of 3 m
- Ambient temperature -25 – +40 °C
- Mounting method flush mounting with SnapFit mounting bracket
- Mounting height 2 – 3.5 m
- Colour white (RAL 9010)
- Drill diameter 76 mm
- Minimum flush mounting depth 56.9 mm
- Dimensions visible (HxWxD) 100 x 100 x 9.5 mm
- Dimensions (HxWxD) 120 x 120 x 66.4 mm
- Wire capacity 1.5/2.5 mm²
- Protection degree IP20
- Impact resistance IK02
- Modification of settings app (iOS/Android) and 2-way Bluetooth® communication
- Maximum range Bluetooth® (free field, depending on the device) 50 m
- Operating frequency 2.4 GHz
- Maximum radio frequency power -2 dBm
- Halogen-free yes
- Marking CE
Detection area
Troubleshooting
Support & contact
- nv Niko sa
- Industriepark West 40
- 9100 Sint-Niklaas, Belgium
- www.niko.eu
- EN
-
- +32 3 778 90 80
- NL
-
- België:
- +32 3 778 90 80
- support.be@niko.eu
- Nederland:
- +31 880 15 96 10
- support.nl@niko.eu
- FR
-
- Belgique:
- +32 3 778 90 80
- support.be@niko.eu
- France:
- +33 820 20 66 25
- support.fr@niko.eu
- Suisse:
- +41 44 878 22 22
- support.ch@niko.eu
- DE
-
- Deutschland:
- +49 7623 96697-0
- support.de@niko.eu
- Schweiz:
- +41 44 878 22 22
- support.ch@niko.eu
- Österreich:
- +43 1 7965514
- support.at@niko.eu
- Belgien:
- +32 3 778 90 80
- support.be@niko.eu
- DK
-
- +45 74 42 47 26
- SE
-
- +46 8 410 200 15
- NO
-
- +47 66 77 57 50
- IT
-
- +41 44 878 22 22
- PL
-
- +48 509 378 373
- SK
-
- +421 2 63 825 155
- support.sk@niko.eu
Niko prepares its manuals with the greatest care and strives to make them as complete, correct and up to date as possible. Nevertheless, some deficiencies may subsist. Niko cannot be held responsible for this, other than within the legal limits. Please inform us of any deficiencies in the manuals by contacting Niko customer services at support@niko.eu.
- support.sk@niko.eu
- +421 2 63 825 155
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>