USX STAR SML019-01 Full Motion TV Wall Mount Bracket Instruction Manual
- June 16, 2024
- USX STAR
Table of Contents
USX STAR SML019-01 Full Motion TV Wall Mount Bracket
Product Information
Specifications:
- TV Size Compatibility: 37-86 inches
- VESA Size Compatibility: MAX: 600mm/23.62 (MIN: 200mm/7.87), MAX: 400mm/15.74 (MIN: 100mm/3.94)
- Weight Capacity: Max 132 lbs (60 kg)
- Wall Compatibility: Wood stud, solid concrete
Product Usage Instructions
Step 1: Check Compatibility
Before getting started, make sure to check the following:
- Check if your TV’s VESA size is within the specified range.
- Check if your TV weighs more than 132 lbs (60 kg).
- Determine the type of wall you have (drywall with wood studs or solid concrete).
Step 2: Gather Tools
Make sure you have the following tools:
- Tape Measure
- Pencil
- Screw driver
- Electric Drill
- 1/2 in. (13 mm) Socket Wrench
- Stud Finder
- 7/32 in. (5.5 mm) Wood Drill Bit
- 3/8 in. (10 mm) Masonry Drill Bit
- Hammer
Step 3: Attach Brackets to TV
- Select the appropriate TV screws based on the size of your TV (M4, M6, or M8).
- Figure out the suitable position of the brackets on your TV, considering low and high mounting holes. Install them up or down if needed.
Step 4: Install Wall Plate
Depending on the type of wall you have, follow one of the two installation
methods:
- Wood Stud Install: Use the provided lag bolts and level to secure the wall plate to the wood studs.
- Concrete Install: If you have solid concrete walls, you will need additional concrete wall anchors. Contact us to have these additional pieces shipped directly to you.
Step 5: Attach Extension Arm and End Support
- Attach the extension arm to the wall plate using the provided bolts.
- Attach the end support to the extension arm using the provided bolts.
Step 6: Fully Assemble Mount
Follow the instructions provided in the manual to fully assemble the mount.
FAQs
-
Q: What should I do if my TV’s VESA size is not within the specified range?
A: If your TV’s VESA size is not within the specified range, this mount is not compatible with your TV. -
Q: Can I exceed the maximum weight capacity?
A: No, you should not exceed the maximum weight capacity indicated. Doing so may result in collapse of the mount and its accessories, causing possible injury. -
Q: Can I install this mount into drywall alone?
A: No, you should not install this mount into drywall alone. It is designed for use in wood stud or solid concrete walls. -
Q: What should I do if I have an unsure wall type?
A: If you are unsure about the type of wall you have, please contact us via Amazon for assistance.
CAUTION: PLEASE READ ENTIRE MANUAL BEFORE USE AND SAVE THESE INSTRUCTIONS.
Before getting started
Dimensions
Parts and Hardware
WARNING: This product contains small items that could be a choking hazard
if swallowed. Before starting assembly, verify all parts are included and
undamaged. If any parts are missing or damaged, do not return the damaged item
to your dealer; contact Customer Service. Never use damaged parts!
NOTE: Not all hardware included will be used.
Parts and Hardware for STEP 1
Parts and Hardware for STEP 2
Parts and Hardware for STEP 3
INSTALLATION
STEP 1 Attach Brackets to TV
STEP 2A Attach Wall Plate to Wall Wood Stud Option
CAUTION: Avoid potential personal injury or property damage!
- Drywall covering the wall, must not exceed 5/8 in. (16 mm)
- Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)
- Maximum horizontal space between fasteners: 16 in. (406 mm)
- Stud center must be verified
-
Locate your studs. Verify and mark the center of the stud by finding the stud edges using a thin nail, or an edge to edge stud finder.
-
Position the mounting template at your desired height and line up the holes with your stud center line. Level the wall plate and mark the hole locations.
-
Drill pilot holes using a 7/32 in. (5.5 mm) diameter drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 2.5 in. (64 mm). Be sure to drill into the center of the studs. -
Install wall plate 06 using four lag bolts 01. Tighten the lag bolts only until they are pulled firmly against the wall plate.
CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts.
STEP 2B Attach Wall Plate to Solid Concrete Wall
CAUTION: Avoid potential personal injury or property damage!
- Mount the wall plate assembly 06 directly onto the concrete surface
- Minimum solid concrete thickness: 8 in. (203 mm)
-
Position the mounting template on the wall at your desired height. Level the wall plate and mark the hole locations.
-
Drill four pilot holes using a 3/8 in. (10 mm) diameter masonry drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 2.5 in. (64 mm). -
Insert four anchors.
CAUTION: Be sure the anchors are seated flush with the concrete surface. -
Insert wall plate 06 using four lag bolts 01. Tighten the lag bolts only until they are pulled firmly against the wall plate.
CAUTION: Improper use could reduce the holding power of the lag bolt.
DO NOT over-tighten the lag bolts.
STEP 3 Extension Arms and end support Assembly
Please make sure you install these extension arms in right direction.
STEP 4 Wall Plate Installation Integrity Test
Before hanging TV, please try to pull the mount to make sure that it has
been assembled on the wall tightly.
STEP 5 Hang and Secure TV to Wall Plate
Hang TV/bracket assembly onto wall plate, wrap clips on bracket around
extension arms and tighten them using bolts 03.
STEP 6 Adjustments
TV leveling adjustment (±4°): Loosen 4 leveling bolts on the rear of TV
plate by maximum 2 turns, adjust to level, and retighten to secure.
Tilting angle adjustment (+5°/-15°): Loosen handle and tilting bolt, adjust TV to your desired position, then tighten handle and tilting bolt. Put the handle level when finish.
Cables manage: Manage TV cables orderly and guide them through the velcros.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>