USX STAR SFM090 Fixed TV Wall Mount Instruction Manual

USX STAR SFM090 Fixed TV Wall Mount

Product Information

Specifications

• TV Interface: MAX:400mm/15.75 MIN:75mm/2.95
• Dimensions:
  • TV Interface: MAX:400mm/15.75 MIN:75mm/2.95
  • 417mm/16.42 (Side View)
  • 33mm/1.30 (Wall Plate)
  • 164mm/6.46
  • 406.4mm/16
  • 203.2mm/8
  • 435mm/17.13
  • 222mm/8.74

Product Usage Instructions

Step 1: Check Compatibility and Gather Tools

1. Check your TV:
   • VESA is within Min and Max size:
   • MAX:400mm/15.75 (MIN:75mm/2.95)
   • MAX:400mm/15.75 (MIN:75mm/2.95)
   • If the VESA size is not within the given range, the mount is NOT compatible.
2. Check TV weight:
   • If the TV (including accessories) weighs MORE than 99 lbs. (45 kg), the mount is compatible.
   • CAUTION: Do not exceed the maximum weight indicated. This mounting system is intended for use only with the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in collapse of the mount and its accessories, causing possible injury.
3. Check wall material:
   • If you have drywall with wood studs, the mount is compatible.
   • If you have solid concrete, the mount is compatible.
   • If you are unsure about your wall material, message us via Amazon for assistance.
   • CAUTION: Do not install into drywall alone.
4. Gather all the tools needed:
   • Tape Measure
   • Pencil
   • Screwdriver
   • Electric Drill
   • 3/8 in. (10 mm) Socket Wrench
   • Stud Finder
   • 1/8 in. (3 mm) Wood Drill Bit
   • 3/8 in. (10 mm) Masonry Drill Bit
   • Hammer

Step 2: Attach Brackets to TV

1. Select TV Screws:
   • M4
   • M6
   • M8
2. Figure out the suitable position of brackets:
   • LOW MOUNTING HOLES
   • HIGH MOUNTING HOLES
   • INSTALL UP/DOWN IF NEEDED
   • TV BRACKETS MUST BE LEVEL
3. Attach the TV Plate:
   • If no spacer is needed, choose suitable screws and washers:
   • D1
   • E1
   • B1
   • If a spacer is needed, choose suitable screws, washers, and spacers:
   • D2
   • F
   • E2
   • B1
   • B2
   • C

Step 2A: Attach Wall Plate to Wall (Wood Stud Option)

1. CAUTION: Avoid potential personal injury or property damage!
2. Locate your studs:
   • Verify and mark the center of the stud by finding the stud edges using a thin nail or an edge-to-edge stud finder.

Parts and Hardware

• WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service. Never use damaged parts!
• NOTE: Not all hardware included will be used.
• Parts and Hardware for Step 1:
  • Wall plate: 01 x 1
  • TV Brackets: 02 x 2
• Parts and Hardware for Step 2:
  • Lag Bolt M6x60mm
  • Washers M6: A x 4
  • Spacers 10mm: B1 x 4
  • Level: B2 x 8
  • Spacers 5mm: B3 x 1
  • C: C x 8
  • TV Screws: M6x15mm, M6x30mm: D1 x 4, D2 x 4
  • TV Screws: M8x15mm, M8x45mm: E1 x 4, E2 x 4
  • TV Screws: M4x30mm: F x 4
  • Concrete wall anchor (NOT INCLUDED): Contact us at telephone 1-800-558-5930 or message us to have these additional pieces shipped directly to you.

Frequently Asked Questions (FAQ)

Q: What is the maximum weight limit for this mount?

A: The maximum weight limit for this mount is 99 lbs. (45 kg).

Q: Can I install this mount on drywall alone?

A: No, this mount should not be installed into drywall alone. It is designed for use in wood stud or solid concrete walls.

Q: How do I determine if my wall is suitable for this mount?

A: If you have drywall with wood studs or solid concrete, your wall is suitable for this mount. If you are unsure about your wall material, please message us via Amazon for assistance.

SFM090 INSTRUCTION MANUAL

For 26-60″ TV
If you have any questions along the way, just message to us. We’re ready to help!

CAUTION: PLEASE READ ENTIRE MANUAL PRIOR TO USE AND SAVE THESE INSTRUCTIONS

Before getting started, let’s check below lists to make sure it is just right for you!

Dimensions

Parts and Hardware

WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact
Customer Service.
Never use damaged parts!

NOTE: Not all hardware included will be used.

• Parts and Hardware for STEP 1

• Parts and Hardware for STEP 2

STEP 1 Attach Brackets to TV

1. Select TV Screws

2. Figure out the suitable position of brackets

3. Need Spacer?

STEP 2A Attach Wall Plate to Wall Wood Stud Option

CAUTION: Avoid potential personal injury or property damage!

• Drywall covering the wall, must not exceed 5/8 in. (16 mm)
• Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)
• Maximum horizontal space between fasteners: 16 in. (406.4 mm)
• Stud center must be verified

1. Locate your studs. Verify and mark the center of the stud by finding the stud edges using a thin nail, or an edge to edge stud finder.
2. Position the Wall plate 01 at your desired height and line up the holes with your stud center line. Level the Wall plate 01 and mark the hole locations.

3. Drill pilot holes using a 1/8 in. (3 mm) diameter drill bit.
   IMPORTANT: Pilot holes must be drilled to a depth of 2.5in. (64 mm). Be sure to drill into the center of the studs.

4. Install wall plate 01 using lag bolts A . Tighten the lag bolts only until they are pulled firmly against the wall plate.
   CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts.
   Go to STEP 3 on PAGE 13.

STEP 2B Attach Wall Plate to Solid Concrete Wall

CAUTION: Avoid potential personal injury or property damage!

• Mount the wall plate assembly unit directly onto the concrete surface
• Minimum solid concrete thickness: 8 in. (203 mm)

1. Position the Wall plate 01 on the wall at your desired height. Level the Wall plate 01 and mark the hole locations.
2. Drill four pilot holes using a 3/8 in. (10 mm) diameter masonry drill bit.
   IMPORTANT: Pilot holes must be drilled to a depth of 2.5 in. (64 mm).

3. Insert anchors.
   CAUTION: Be sure the anchors are seated flush with the concrete surface.

4. Insert wall plate 01 using lag bolts A . Tighten the lag bolts only until they are pulled firmly againstthe wall plate.
   CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts.

STEP 3 Wall Plate Installation Integrity Test

Before hanging TV, please try to pull the mount to make sure that it has been assembled on the wall tightly.

STEP 4 Hang and Secure TV to Wall Plate

STEP 5 Take Down the TV from the Mount

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>