ERAY-196 Fingerprint Door Lock Set Instruction Manual
- June 15, 2024
- ERAY
Table of Contents
ERAY-196 Fingerprint Door Lock Set
After-sales Email: service@erayvip.com
Product Information
TIPS:
- This lock is equipped with mechanical keys for manual unlocking. Remove mechanical keys from the package and keep them in a safe place and always have access to them.
- To power on the lock, four alkaline MA batteries (not included) are required. Non-alkaline and rechargeable batteries are not recommended.
- This lock is not designed to be exposed to direct sunlight or rain. It is not water proof IP rated.
- Keep your fingers clean when using this lock.
Diagram of Door Lock Installation
TIPS:
- Install the spindle onto the latch, and get the cables through the middle of spindle.
- Fix the rear fixing plate, front handle with two screws on the door.
Accessory
Open the product package. Check that the following accessories are included.
Door Opening Direction
- Right handle opening
- Left handle opening
Installation
Please follow the below steps to install the lock
-
Adjust the backset of the lock body (60mm or 70mm) if required. When adjusting the backset, the square hole must be pulled to the edge of the chute, and the front and rear square holes must be horizontal.
-
Fix the latch with 2 screws.
Measure the Door Size
size Make is sure 2-3/8″ door or thickness 2-3/4″with is the 1.38-2.16″, deadbolt. door hole diameter is 2-1/8″, measure backset
TIPS
- Available door thickness 35mm-55mm. If the door is over this range. please contact us for more information.
- Please select the correct accessories according to your door thickness.
-
Fix door the frame. strike plate with 2 screws on the dooor frame.
-
Reset” button
-
Free Passage” button
Check Points After Installation
- The face plate is horizontal with the door.
- The Latch bolt must works smoothly and flexibly!
- Please make sure the cable will not be pressed.
- Fix the handle with two screws, and check if it works fine.
- Install the batteries, and cover the battery cover.
System Reset:
“Auto Lock” &” Free Passage” Mode Setting
TIPS:
- Repeat Method 1 or Method 2 to switch from “Free Passage” Mode to “Auto Lock” Mode, and vice versa.
- Enter an administrator’s fingerprint or passcode to unlock the door, and switch to “Auto Lock” Mode.
- Press the “#” key in the outside handle to change to “Auto Lock” Mode.
Parameters
Unlocking Methods | Fingerprint/ Passcode/ Mechanical Key/ Free Passage |
---|---|
Direction of Door Opening | Left/ Right (Universal) |
Power Supply | 4* AAA Batteries/ External USB Power Supply (for Emergency) |
Number of Users | Fingerprint: max. 50; Passcode: max. 100 |
TIPS:
Firstly touch the panel to wake up the lock before any operation with touch-
control area. Any fingerprint or initial test passcode (123456#) can unlock it
if no user is enrolled.
Adding User (Fingerprint/ Passcode)
- Step 1: Adding the First User/ Administrator
- Step 2: Adding Other Fingerprints
- Step 3: Adding Other Passcodes
TIPS:
- The first 3 verified users are administrators, and the others are general users.
- Only the first administrator’s setting is different from others. For example, if you set a “fingerprint” as the first user, the following users, whether it’s a fingerprint or a password, should be set by following the “Step 2” or “Step 3”.
- If the display goes off during the operation, please restart the steps.
- When adding fingerprints, try to ensure that multiple areas of the finger are read.
Unlocking & Locking
Fingerprint
Mechanical Keys
Use E-Key to unlock/lock
TIPS:
- Before seting users or when failing to set users, anything that touches the fingerprint reader can unlock as long as its temperature is close to body temperature.
- If the lock beeps 3 times.the red light goes on then turns steady green light, and the unlocking fails, please try again.
Adjusting the Volume (Default is the highest volume,it cannot mute)
Emergency Supply
TIPS:
While low battery, Use your power bank plug here for emergency power supply.
(Can not be charged)
- Keep at least one key out of the door for emergency.
- When the battery is low, the indicator will blink red light. The rest power could only be used for about 30 times.
- When the battery is out of power, you can unlock the door with key, or supply the lock with power through the micro-USS port and use fingerprint or password to unlock it.
- Use alkaline batteries to prevent the damage by battery leakage. If not used for a long time, please remove the battery.
Specifications
- Product Name: [Product Name]
- Model Number: [Model Number]
- Dimensions: [Dimensions]
- Weight: [Weight]
- Power Source: [Power Source]
- Connectivity: [Connectivity Options]
Product Usage Instructions
Section 1: Administrator Setup
- Make sure the device is powered on and ready for setup.
- If you are one of the first 3 users, you will be an administrator. If not, skip to Section 2.
- Follow the specific instructions provided for the first administrator’s setting. This may involve setting up a fingerprint or password.
Section 2: General User Setup
- If you are a general user (not one of the first 3), follow these steps:
- Ensure that the device is powered on and in setup mode.
- If the previous user was using a fingerprint, place your finger on the fingerprint sensor and wait for verification. If the previous user was using a password, enter the password when prompted.
- Once verified, follow the instructions on the screen to set up your fingerprint or password.
Section 3: Troubleshooting
If the display goes off during the operation, please restart the steps you
were following. This may involve powering off and on the device or returning
to the previous step in the setup process.
Section 4: Adding Fingerprints
When adding fingerprints, it is important to ensure that multiple areas of
the finger are read. This helps improve accuracy and reliability.
Follow these steps to add fingerprints:
- Access the fingerprint setup menu from the device’s settings.
- Place your finger on the fingerprint sensor and hold it steady until the device successfully reads your fingerprint.
- If prompted, adjust the position of your finger slightly and try again until the device captures a clear and accurate fingerprint.
- Repeat the process for additional fingers if desired.
Frequently Asked Questions (FAQ)
How many administrators can be set up?
The system allows for a maximum of 3 administrators.
Can I change my administrator settings?
Yes, as an administrator, you can access the settings menu to modify your administrator preferences.
What should I do if I forget my password?
If you forget your password, please refer to the user manual for instructions on how to reset it. This may involve using a backup password or contacting customer support.
Can I add multiple fingerprints for one user?
Yes, you can add multiple fingerprints for one user. Please follow the instructions provided in the Adding Fingerprints section above.
Why anyone's fingerprints can unlocked the lock?
The newly arrived fingerprint lock is an automatic program, all fingerprints can unlock under this program, you need to add the administrator fingerprint before continuing the subsequent programming. Note: If the fingerprint addition fails, the program will not be canceled, please re-add the fingerprint.
Why does it keep failing when adding a password?
Password must be 6-10 digits to take effect.
After installing the fingerprint lock, what should I do if the keyboard light of the fingerprint lock does not light up?
It is possible that the connection cable is squeezed during installation, resulting in poor contact. Please adjust the position of the connection cable appropriately.
Why do I keep getting an error when I recognize my fingerprint?
When adding fingerprints, try to ensure that multiple areas of the finger are read.
Why does the fingerprint lock not automatically lock after unlocking?
Some newly arrived locks have disabled the automatic locking mode, please turn on the automatic locking manually. See P.4 for more information Auto Lock Mode Free Passage Mode Setting
When I use my fingerprint or passcode to unlock, the green light is on but I can’t unlock it normally.
It may be that the center of the lock cylinder is not positioned correctly when you reinstall it, you can readjust it and try again.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>