Origin 21 10550GNMB30 LED Linear Chandelier Instruction Manual

: June 15, 2024
: Origin 21

Table of Contents

Origin 21 10550GNMB30 LED Linear Chandelier
PACKAGE CONTENTS
SAFETY INFORMATION
ASSEMBLY INSTRUCTIONS
CARE AND MAINTENANCE
WARRANTY
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Origin 21 10550GNMB30 LED Linear Chandelier

LED Linear Chandelier

Specifications

Model: 10550GNMB30
Item Number: 5336488
Trademark: ORIGIN 21and logo design
Manufacturer: LF, LLC
Approved for use in damp locations (Intertek 5005395)

Assembly Instructions

Remove the mounting plate screws (F) from the edge of the mounting plate (D).
Wrap electrical tape around each individual wire connector (AA) down to the wire.
Align the holes in the edge of the canopy (E) with the holes on the edge of the mounting plate (D).
Attach the canopy (E) to the mounting plate (D) using the mounting plate screws (F) previously removed.
Arrange the preassembled rings on the fixture (A) as desired.
Restore power and test the fixture (A). If the light does not function, please refer to the troubleshooting section.

Care and Maintenance

To ensure the longevity of your LED Linear Chandelier, follow these care and maintenance guidelines:

Regularly dust the fixture with a soft, dry cloth.
Avoid using harsh chemicals or abrasive cleaners on the fixture.
Do not expose the fixture to excessive moisture or humidity.

Troubleshooting

Problem	Possible Cause	Corrective Action
Light does not come on initially or no longer comes on.	1. Power is OFF.

2. Faulty connection.
3. LED component is not working properly.| 1. Make sure power supply is ON.
2. Check wiring and all connections.
3. Contact Customer Service.
Fuse blows out or circuit breaker trips.| 1. Crossed wires.
2. Power wire is grounding out.| 1. Check wiring.
2. Check all connections.

FAQ

Q: Where can I purchase replacement parts?
A: You can contact our customer service department at 1-888-251-1026 or visit www.lowespartsplus.com for replacement parts.

Q: Can this chandelier be used in a bathroom?
A: Yes, this chandelier is approved for use in damp locations according to Intertek 5005395.

ITEM #5336488

LED LINEAR CHANDELIER
MODEL #10550GNMB30

Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-888-251-1026 , 8:00 a.m. – 8 p.m., EST, Monday – Sunday. You could also contact us at partsplus@lowes.com or visit www.lowespartsplus.com.

PACKAGE CONTENTS

PART	DESCRIPTION	QUANTITY
A	Fixture	1
B	6-inch Rod	1
C	12-inch Rod	4
D	Mounting plate	1
	(preassembled to canopy (E))
E	Canopy	1
F	Mounting plate screw	2

G

| (preassembled to canopy (E))

Fiberglass sleeve

| ****

1

Origin-21-10550GNMB30-LED-Linear-Chandelier-1

HARDWARE CONTENTS (shown actual size)

SAFETY INFORMATION

READ AND SAVE THESE INSTRUCTIONS.

DANGER

For your protection and safety, carefully read and understand the information provided in this manual completely before attempting to assemble, install or operate this product. Failure to do so could lead to electrical shock, fire or other injuries that could be hazardous or even fatal.
DO NOT connect this fixture to an electrical system that does not provide a means for equipment grounding. Never use a fixture in a two-wire system that is not grounded. Installing a fixture into an electrical system not having a proper grounding means could cause metal parts of the fixture to carry electrical currents if any of the fixture wires, wire connections or splices were to become broken, cut or loose during the mounting or normal operation of the fixture. Under this condition, anyone coming in contact with the fixture would be subject to electrical shock, which could cause serious injury or death.
DO NOT connect the bare or green insulation fixture ground wire to the black (HOT) current-carrying wire or the white (NEUTRAL) house wire. Connection of the bare or green fixture ground wire to the black or white house wires may cause metal parts of the fixture to carry electrical currents. Under this condition anyone coming in contact with the fixture will receive electrical shock, which could cause serious injury or death.
DO NOT damage or cut the wire insulation (covering) during installation of fixture. DO NOT permit wires to contact any surface having a sharp edge. To do so may damage or cut the wire insulation, which could cause serious injury or death from electrical shock .

WARNING

All electrical connections must be in agreement with local codes and ordinances, the National Electric Code (NEC) and ANSI/NFPA 70-1999. Contact your municipal building department to learn about your local codes, permits and/or inspections. Risk of fire – most dwellings built before 1985 have supply wire rated for 140°F. Consult a qualified electrician before installation.
To avoid personal injury, the use of gloves may be necessary while handling fixture parts with sharp edges.
DO NOT suspend any fixture by the house wires. A fixture must always be mounted directly to an outlet box or to a mounting plate which is first attached to the outlet box. Wire connectors will not support the weight of a fixture. Suspending a fixture by the house wires and wire connectors will result in the fixture falling, with the possibility of personal injury and the danger of electrical shock
or fire.

DANGER

To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this light fixture are designed to accept only one 12-gauge house wire and two lead wires from the light fixture. If your house wire is larger than 12-gauge or there is more than one house wire to connect to the corresponding fixture lead wires, consult an electrician for the proper size wire connectors to use.
To reduce the risk of damage to the fixture, DO NOT use power tools to assemble any part of the fixture.
Modifications not approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Distributed by: Lowe’ Home Centers LLC, 1000 Lowe’ Blvd., Mooresville, NC 28117; 1-888-251-1 026

CAUTION

TURN OFF ELECTRICITY at main fuse box (or circuit breaker box) before beginning installation by removing the fuse (or switching the circuit breaker off).
If you are not sure the lighting system has a grounding means, DO NOT attempt to install this fixture. Contact a qualified, licensed electrician for information regarding the proper grounding methods as required by the local electrical code in your area.
All fixtures must be mounted to an outlet box that is supported by the building structure.
If a dimmer control switch is used with this fixture, obtain professional advice to determine the correct type to use as well as the electrical rating required.
Do NOT tamper with or attempt to repair LED component of fixture. The light source is designed for this specific application and should not be serviced by untrained personnel. If any servicing is required, call our customer service department.

NOTE: Dimmable to 10% with select dimmers.

PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

Estimated Assembly Time: 30 minutes
Tools Required for Assembly (not included): Flathead Screwdriver, Phillips Screwdriver, Wire Strippers, Pliers, Wire Cutters, Safety Glasses, Stepladder, Electrical Tape
Helpful Tools (not included): A/C Tester Light, Do-It-Yourself Guide, Soft Cloth

ASSEMBLY INSTRUCTIONS

Remove mounting plate (D) from canopy (E) by removing mounting plate screws (F) from the edges of the canopy (E).
Save mounting plate screws (F) for later use.
Attach mounting plate (D) to outlet box (not included) using existing washers and outlet box screws or the machine screws (BB). NOTE: If the outlet box screws required for your outlet box are of a different size than the machine screws (BB), consult a licensed electrician before proceeding.
Tighten machine screws (BB) to secure mounting plate (D) to outlet box.
Hardware Used
Locate swivel connector piece under canopy (E).
Rotate swivel connector piece until it aligns with base of canopy (E). [NOTE: This may require some force.]
There are several different ways to use the fixture (A) depending on the number and combination of rods (B and/or C) you decide to use.
b. If you wish to use the fixture (A) with all five rods (B and C), thread wires from fixture (A) through all 12-inch rods (C) and the 6-inch rod (B). Secure all rods (B and C) by screwing the
ends of each one together. Be sure rods (B and C) are completely connected, then carefully thread the wires through the fiberglass sleeve (G) and into the swivel connector piece on the underside of the canopy (E). [NOTE: Wires must go through the sleeve when threading them through the swivel connector piece.] Pull wires completely through top of canopy (E) and then secure last rod (B or C) to underside of canopy (E). Be sure all rods (B and C) are completely secure before proceeding to Step 7.
If you wish to use the fixture (A) with fewer rods (B and/or C) or a combination of both rod sizes, decide which rods (B and/or C) will be used. Then, thread wires from fixture (A) through 12-inch rod(s)(C) and/or the 6-inch rod (8). Secure all rods (B
and/or C) by screwing the ends of each one
together. Be sure rods (B and/or C) are completely connected, then carefully thread the wires through
the fiberglass sleeve (G) and into the swivel connector piece on the underside of the canopy (E). [NOTE: Wires must go through the sleeve when threading them through the swivel
connector piece.] Pull wires completely through top
of canopy (E) and then secure last rod (B or C) to underside of canopy (E). Be sure all rods (B and/or C) are completely secure before proceeding to Step 7.
Locate molex connector inside the canopy (E).
Press tab on molex connector in order to insert YELLOW wire from fixture (A) into one of the 2 holes across from the YELLOW wire from driver (E). Repeat this process for the RED wire from the fixture (A). Make sure connections are secure.
a. Depending on the number of rods used, you may need to cut the excess length on the WHITE and BLACK wires. You will need at least 10 inches of wire to work with.
Prepare wire by stripping 3/4 in. of insulation from wire ends using wire stripper (not included). Tie wire into a knot inside canopy (E).
b. Connect BARE wire from canopy (E) to BARE /GREEN ground wire from outlet box using wire connector (M). Connect WHITE wire from canopy (E) to WHITE wire from outlet box using existing wire connector or wire connector (M). Connect BLACK wire from canopy (E) to BLACK wire from outlet box using existing wire connector or wire connector (M).
NOTE: Screw wire connectors (M) on in a clockwise direction.
WARNING: Never connect BARE/ GREEN ground wire to WHITE or BLACK power supply wires.

  * To reduce the risk of fire, electrical shock, or personal injury, wire connectors provided with this light fixture are designed to accept only one 12-gauge house wire and tow lead wires from the light fixture. If your house wire is larger than 12-gauge or there is more than one house wire to connect to the corresponding fixture lead wires, consult an electrician for the proper size wire connectors to use.

Wrap electrical tape (not included) around each individual wire connector (AA) down to the wire.
WARNING: Make sure no bare wire or wire strands are visible after making connections.
Gently push wire connectors (AA) and excess wiring back into outlet box.
Align holes in edge of canopy (E) with holes on edge of mounting plate (D). Attach canopy (E) to mounting plate (D) using the mounting plate screws (F) previously removed (Step 1, Page 5).
Arrange preassembled rings on fixture (A) as desired. Restore power and test fixture (A).
If light does not function, please refer to TROUBLESHOOTING on the following page.

CARE AND MAINTENANCE

Shut off main power supply. Wipe fixture with soft, damp cloth. Do not use an abrasive cleaner on fixture.
Total wattage for this fixture is 31 watts; do not attempt to replace the LEDs.

TROUBLESHOOTING

WARNING: Before beginning work, shut off the power supply to avoid electrical shock.

PROBLEM	POSSIBLE CAUSE	CORRECTIVE ACTION
Light does not come on	1. Power is OFF.	1. Make sure power supply is ON.
initially or no longer	2. Faulty connection.	2. Check wiring and all

WARRANTY

The distributor warrants all of its lighting fixtures against defects in materials and workmanship for one (1) year from the date of purchase. If within this period the product is found to be defective, take a copy of the bill of sale as a proof of purchase and the product in its original carton to the place of purchase. The distributor will, at its option, repair, replace or refund the purchase price to the consumer. All costs of installation and removal of the fixture is the responsibility of the consumer. This warranty does not cover fixtures becoming defective due to misuse, accidental damage or improper handling and/or installation and specifically excludes liability for direct, incidental or consequential damages. As some states do not allow exclusions of limitations on an implied warranty, the above exclusion and limitation may not apply. This warranty gives you specific rights and you may also have other rights which may vary from state to state.