Schneider Electric PowerPacT H J Frame and TeSys GV5 Circuit Breakers Installation Guide
- June 15, 2024
- Schneider Electric
Table of Contents
Schneider Electric PowerPacT H J Frame and TeSys GV5 Circuit Breakers
Product Usage Instructions
Specifications
- Product Name: Terminal Cover and Lug Shield Kits
- Model Number: 48940-223-02
Installation
- Turn off all power supplying this equipment.
- If a circuit breaker is installed, remove it from the installation.
- For lug shields (kits S37446, S37447, and S37448) used with control wires, remove tab (A) for control wire leads from the terminal cover.
- Reinstall the circuit breaker as outlined in the circuit breaker instruction manual shipped with the circuit breaker.
- For lug shields (kit numbers S37446, S37447, and S37448):
- Insert wires as instructed per the instruction bulletin provided with the circuit breaker.
- Remove the protective coating from the lens, if installed.
Frequently Asked Questions
- Q: Who should install, operate, service, and maintain the electrical equipment?
- A: Electrical equipment must be installed, operated, serviced, and maintained only by qualified personnel.
- Q: Are there any trademarks associated with this product?
- A: Yes, Schneider Electric, Square D, PowerPacT, and TeSys are trademarks and the property of Schneider Electric SE, its subsidiaries, and affiliated companies. All other trademarks are the property of their respective owners.
- Q: Where can I contact Schneider Electric for support?
- A: You can contact Schneider Electric at the following locations:
- Schneider Electric USA, Inc.: 800 Federal Street Andover, MA 01810 USA, 888-778-2733, www.se.com/us
- Schneider Electric Canada, Inc.: 5985 McLaughlin Road Mississauga, ON L5R 1B8 Canada, 800-565-6699, www.se.com/ca
- Schneider Electric Square D: 6: 100102 (010) 8434-6699, www.se.com/cn
Terminal Cover and Lug Shield Kits for PowerPacT™ H/J-Frame and TeSys™ GV5 Circuit Breakers
Retain for future use.
Kit Contents
Kit| Part| H-frame 60 A| H-frame 150 A GV5PB150|
J-frame GV5PB250| Qty
---|---|---|---|---|---
Terminal Cover Kit
S37436 S37440
| Terminal Covers| | | ****
1
Screws| |
2
| | S37446
| S37447
| S37448
|
Lug Shield Kit
**** S37446 S37447 S37448
| Lug Shields| | | | ****
1
Wire Range| #14–#3 AWG
(2.5–27 mm2)
| #14–3/0 AWG (2.5–95 mm2)| #4 AWG–350 kcmil
(20–185 mm2)
|
Screws| |
3
| Lense| | | ****
1
Tool Required
- Phillips #2 Screwdriver
- Pliers
Installation
DANGER: HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
- Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See NFPA 70E, CSA Z462, NOM 029-STPS or local equivalent.
- This equipment must be installed and serviced only by qualified electrical personnel.
- Turn off all power supplying this equipment before working on or inside equipment.
- Always use a properly rated voltage sensing device to confirm power is off.
- Replace all devices, doors and covers before turning on power to this equipment.
Failure to follow these instructions will result in death or serious injury.
- Turn off all power supplying this equipment.
- If circuit breaker is installed, remove from installation.
- For lug shields (kits S37446, S37447, and S37448) used with control wires, remove tab (A) for control wire leads from terminal cover.
- Install terminal covers (A) or lug shields (B) onto circuit breaker using screws (C) provided. Torque screws to 10.6 lb-in. (1.2 N•m).
- Reinstall circuit breaker as outlined in circuit breaker instruction manual shipped with circuit breaker.
- For lug shields (kit numbers S37446, S37447 and S37448):
- Insert wires as instructed per instruction bulletin provided with circuit breaker.
- Remove protective coating from lense, if installed.
- Install lense (D) over wire binding screw access ports using screw (E) provided. Torque screws to 10.6 lb-in. (1.2 N•m).
Terminal Cover and Lug Shield Installation
Electrical equipment must be installed, operated, serviced, and maintained
only by qualified personnel. No responsibility is assumed by Schneider
Electric for any consequences arising out of the use of this material.
Schneider Electric, Square D, PowerPacT and TeSys are trademarks and the
property of Schneider Electric SE, its subsidiaries, and affiliated companies.
All other trademarks are the property of their respective owners.
Contact
Schneider Electric USA, Inc.
- 800 Federal Street Andover, MA 01810 USA
- 888-778-2733
- www.se.com/us
© 2004-2023 Schneider Electric All Rights Reserved
References
- Schneider Electric Canada | Global Specialist in Energy Management and Automation
- se.com/cn
- Schneider Electric Mexico | Servicios de Renovación y Retrofit de Schneider Electric
- Schneider Electric USA | Global Specialist in Energy Management and Automation
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>