DECADOM Duna 48×32 LED Mirror Medicine Cabinet Installation Guide

DECADOM Duna 48×32 LED Mirror Medicine Cabinet

Product Information

Specifications

• Product : Cabinet
• Adjustment Feature : Three-way adjustment
• Adjustment Options : Height, side-to-side, level, and depth
• Door Orientation : Right side and left side

Product Usage Instructions

Initial Setup

1. Unpack the cabinet and ensure all parts are included.
2. Identify the right side and left side of the cabinet.
3. Place the cabinet in the desired location.

Optional Door Adjustment
The cabinet doors may require adjustment after shipping. Follow these steps to adjust the doors

Height Adjustment

1. Slightly close the hinge of the door.
2. Locate the middle screw on the hinge.
3. Using a screwdriver, turn the middle screw clockwise to raise the door or counterclockwise to lower the door.

Side-to-Side Adjustment

1. Fully extend the hinge of the door.
2. Identify the front and back screws on the hinge.
3. Using a screwdriver, turn the front screw clockwise to move the door towards the right side or counterclockwise to move it towards the left side.
4. Use the back screw in a similar manner to adjust the door side-to-side.

Level and Depth Adjustment
For level and depth adjustment, please refer to the detailed instructions provided in the user manual.

FAQ

• Q: What should I do if the cabinet doors are misaligned?
  A: If the cabinet doors are misaligned, you can use the three-way adjustment feature to align them properly. Follow the steps mentioned in the user manual for height, side-to-side, level, and depth adjustments.

• Q: Can I adjust the doors while they are fully attached to the cabinet?
  A: Yes, you can adjust the doors even when they are fully attached to the cabinet. Simply follow the instructions mentioned in the user manual and make sure to access the appropriate screws based on the hinge position.

FEATURES

• ETL Certified Residential & Commercial
• Digital Clock v2.0 | 12hr – 24hr
• Room Temp Display °C/ °F
• Touch Screen Buttons
• Light Setting Auto Memory
• Dimmable | 3 Color LED Task Lights
• Color Temp 2.500K – 6.500K
• Cri 90 LED Bulb’s Upto 2281LM
• Defogging Full Mirror
• Concealed Finger Door Open
• LED Interior Light, Auto On/oFF Sensor
• Double Side Mirror Doors
• Mirrored Interior Back Wall
• Cosmetic Mirror LED | 3x Magnify
• Adjustable 8 mm Tempered Glass Shelves
• Concealed Shelf Clips
• Blum Hinge 170° Swing | Soft Close
• IP 44 & IP 65.4 Rated | Dust & Watertight
• Dual Outlet – Dual USB Ports
• Easy OFF – Side Mirrors for Recessed Install
• Installation Kit Included

IMPORTANT SAFETY INSTRUCTIONS
When using an electrical furnishing, basic precautions should always be followed, including the following:

• DANGER READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING THIS CABINET.

• WARNING To reduce the risk of burns, fire, electric shock or injury to persons. Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer. Never drop or insert any object into any opening. Do not use outdoors.

• WARNING Risk of electric shock. Connect this furnishing to a properly grounded circuit only.

• CAUTION Total/Maximum shelf load 35lbs/15.8kg
  See Grounding instructions
  This product must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the product.

• WARNING An Electrical option cabinet must be wired to a 15 Amp GFI (Ground Fault Interrupter) protected circuit when used in bathrooms and all other locations required by the National Electric Code.

PLEASE SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

TOOLS REQUIRED FOR ASSEMBLY

PARTS

DIMENSIONS

| 2432L/R| 3032| 3632| 4832
---|---|---|---|---
A| 24″| 30″| 36″| 48″
B| 32″| 32″| 32″| 32″
C| S”| S”| S”| S”
| 23.S”x31.S”x4.S”| 29.S”x31.S”x4.S”| 35.S”x31.S”x4.S”| 47 .S”x31.S”x4.S”
| 2430L/R| 3030| 3630| 4830
---|---|---|---|---
A| 24″| 30″| 36″| 48″
B| 30″| 30″| 30″| 30″
| C| S”| S”| S”| S”
Rr- ,1s1zES| 23.S”x29.S”x4.S”| 29.S”x29.S”x4.S”| 35.S”x29.S”x4.S”| 47.S”x29.S”x4.S”
| 2432L/R| 3032| 3632| 4832
---|---|---|---|---
A| 24″| 30″| 36″| 48″
B| 32″| 32″| 32″| 32″
C| S”| S”| S”| S”
| 23.S”x31.S”x4.S”| 29.S”x31.S”x4.S”| 35.S”x31.S”x4.S”| II 47.S”x31.S”x4.S”

NOTE : Determine overall medicine cabinet dimensions. If recessing medicine cabinet, determine rough-in dimensions.
NOTE : All dimensions & specifications are approximate and subject to change without notice

PRIOR TO MOUNTING

1. Remove Door/s Prior mounting your cabinet. Start with unplugging the door from the cabinet
2. While supporting the door release the lever under the hinge arm (See Illustration 2A). Slide the door off the frame.

ELECTRIC CONNECTIONS

ALL WIRING SHOULD BE DONE BY A QUALIFIED LICENCED ELECTRICIAN

WARNING : Shut off power before wiring the cabinet.

WARNING : An Electrical option cabinet must be wired to a 15 Amp GFI (Ground Fault Interrupter) protected circuit when used in bathrooms and all other locations required by the National Electric Code.

CAUTION : This product must be connected to a grounded, metal permanent wiring system or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the product.

CAUTION : Requires 120 VAC 15 Amp GFI protected circuit.

RECESS-MOUNT INSTALLATION
Make Rough Opening and Frame on all sides. Reference your Cabinet Model Dimensions and Rough in dimensions on Page 4. Make sure the cabinet door has a clearance of at least 1″ from the top of the faucet and 1″ from the ceiling. Electric wiring: Be sure to provide enough wire to make the proper and safe connection to the Field/Power. Place cabinet in rough-in and make sure the cabinet is square, level and plumb. Secure the cabinet with the mounting screws into the framing studs.

RECESS-MOUNT INSTALLATION

1. Draw the perimeter of the medicine cabinet on the wall.

2. Cut the marked perimeter with appropriate tool.

3. Frame the cutout opening (See Illustration below)

4. Place and hold the medicine cabinet in the cutout opening.

5. Level, then secure the medicine cabinet with the screws through the mounting holes into the framing studs.

6. Choose the position for your shelves, then snap in shelf clips (F) into side holes of the cabinet.
   4 STEPS TO FRAME THE CUTOUT OPENING

7. GLASS SHELF INSTALLATION

   • . Push a side of the glass shelf into the left or the right pins.
   •  Snap the glass shelf into the opposite side.

SURFACE-MOUNT INSTALLATION

OPTIONAL DOOR ADJUSTMENT
Doors may need to be adjusted after the initial shipping of the cabinet. The cabinet doors have a three-way adjustment feature.
Height, side-to-side, level, and depth can be adjusted. With the hinge slightly closed you can access the middle screw for up/down adjustment. With the hinge fully extended you can access the front and back screws. These screws will move the door side to side and in and out.

SURFACE-MOUNT INSTALLATION

1. Level and mark the medicine cabinet’s location on the wall from point a to point b.
2. Attach bottom bracket (E) to the wall. Level and mark.
3. Insert top mounting bracket (D) into the top of the cabinet (A).
4. With assistance, rest the medicine cabinet (A) on the bottom mounting bracket (E) and hold it in place.
5. You can slide top mounting brackets (D) to the left or right to achieve a desired position.
6. Attach the top mounting brackets to the wall using a drill
7. Insert clear snap in shelf clips (F) into side holes of the cabinet

SURFACE-MOUNT INSTALLATION
Connect the glass shelves (C) to the cabinet by pushing the side of the shelf in the left or right clip and snapping the shelf down.

NOTE : For more details on the shelf installation please refer to Page 7, Step 7.

MOUNTING BRACKETS INSTALLATION DETAILS

1. Slide top brackets into channel at the top of the cabinet.
2. Make sure top brackets are locked in the grooves.
3. IMPORTANT : Top mounting brackets must be attached to furring trio/channel or wall studs.

FINAL ASSEMBLY

1. Slide the doors into place by pinching the end of the hinge
2. Plug the door into the cabinet.
   •  Insert clear snap in shelf clips (F) into holes on the sides of the cabinet (A).
   •  Push the side of the shelf (C) in the left or right clip and snap the shelf (C) down.

SETUP PROGRAM MODE

Button Functionality for Defogger, Light & Dimmer

• DEFOGGER : touch ****key to turn on/off defogging function.
• LIGHT : touch ****key to turn on/off lighting function.
• Hold key to dim or brighten the light.
• LIGHT : tap key to rapidly switch color temperature of the light.
• Hold key to gradually switch the color of the light.

Setting Digital Clock & Room Temperature mode
Hold key more than two seconds and enter setup mode. Clock will cycle digits for 12/24, hours, minutes & C°/ F° with 3 second intervals.

ENTER Setup MODE

• Hold key time 12H / 24H will start to flicker, tap your selection.
• Hold key will move you to next step HOURS, tap your selection.
• Hold key will move you to next step, MINUTES, tap your selection.
• Hold key will move you to next step, C°/ F° tap your selection & just Let GO.

Use and Maintenance

CAUTION : Maximum total shelf load 35 LBS. Cabinet and doors are constructed of mirrored glass and aluminum. Use a damp cloth to clean your cabinet and mirrors. Do not use any abrasive Materia as it may damage the surface and nish of the cabinet. A mild detergent may be used to clean the surfaces of the cabinet.

TROUBLESHOOTING

For service and parts information please email: sales@decadom.com

• For installation questions contact
• DECADOM
• 877-505-0002

All rights reserved. This material may not be reproduced, displayed, modified or distributed without the express prior written permission of the copyright holder.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>