Xbuyee 240W LED Parking Lot Light User Manual
- June 15, 2024
- Xbuyee
Table of Contents
Xbuyee 240W LED Parking Lot Light User Manual
FOR PHOTOCELL
The fixture is equipped with dusk-to-dawn photocell. To enable dusk-to-dawn operation, please remove the cover. Also keep the cover for future use (Fig.10).
Note: When power is turned on, and the ambient light level is not low
enough to activate the photocell, luminaire will be in standby mode and give
off a very dim glow. This is normal operation. It consumes as little as 0.3W
of energy in standby mode.
WATTAGE SWITCHABLE
The fixture is equipped with three working wattage options, 240W / 200W / 150W. The default wattage is 240W. To change it, please follow the steps below:
-
Remove the cover by screwdriver (Fig.11).
-
Set the switch to the corresponding wattage position (Fig.12).
-
Put the cover back and tighten it by screwdriver (Fig.13)
CARE AND MAINTENANCE
Use only a mild soap and/or water with a soft cloth to clean the fixture. Harsh chemicals will damage the fixture. Do not wipe the fixture with a rough cloth that may scratch the finish or the lens.
PACKAGE CONTENTS
| PART | DESCRIPTION | QUANTITY |
|---|---|---|
| A | LED Area Fixture | 1PC |
| B1 | 1PC | |
| B2 | Arm bracket | 1PC |
| C | Screw (1/2-131 3/4″) | 1PC |
| D | Screw (5/16-18*1″) | 4PCS |
| E | Screw and nuts (1/2-13 * 2 “) | 2PCS |
| F | Spring washer(5/16) | 4PCS |
| G | Flat gasket(5/16) | 4PCS |
Note : Hardware not shown to actual size
SAFFETY INFORMATION
WARNING:
Risk of Fire, Electrical Shock, Cuts or other Casualty Hazards-
Installation and maintenance of this product must be performed by a qualified
electrician. This product must be installed in accordance with the applicable
installation code by a person familiar with the construction and operation of
the product and hazards involved.
WARNING: TO reduce risk of fire electric shock or injury to persons.
- Risk of Fire and Electric Shock-Make certain power is OFF before starting installation or attempting any maintenance. Disconnect power at fuse or circuit breaker.
- Risk of Burn-Disconnect power and allow fixture to cool before handling or servicing.
- Suitable for wet location and operation in temperatures not exceeding 122 °F/50°C.
- For use in 100-277Vac application. Replace the lens if damaged.
- There are no serviceable parts inside the fixture.
- Risk of Personal Injury- Fixture may become damaged and/or unstable if not installed properly. Failure to comply with these instructions may result in death, serious bodily injury and property damage.
SAVE THESE INSTRUCTIONS. For safest operation, read and become familiar with complete Installation instructions prior to use. Pay close attention to this manual and stay within its guidelines when using this product.
CAUTION :
- All parts must be used as indicated in this manual. Do not substitute any parts, leave parts out, or use parts that are worn out or broken. Failure to obey this instruction could invalidate the ETL certification.
- LEDs emit bright light. Avoid looking directly at the light source.
PREPARATION
Before beginning assembly, installation, or operation of product, make sure all parts are present. Compare parts with package and hardware contents list on page 1. If parts is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for replacement parts.
INSTALLATION INSTRUCTIONS
-
Put wire of the fixture A through arm bracket, then assemble the arm. bracket to fixture A with four screws (Fig.1).
-
Loosen the two screws on the side of the arm bracket and remove the cover (Fig.2).
-
Align the arm bracket holes with the holes drilled on the square pole, and fix arm bracket on the pole with screw and nuts E (Fig.3).
-
Pull out the pole wire through the bracket (Fig.4).
-
Put wire of the fixture Arm bracket through the and assemble bracket to the fixture with screw (Fig.5),
-
AC Input Wiring (Fig.6) Connect fixture to supply wires
a. Connect supply line wire to fixture black lead.
b.Connect supply neutral wire to fixture white lead .
C.Connect supply ground wire to fixture green leat. -
0-10V Dimming Wiring (Fig.7). (If dimming, use with 0-10V dimming switch, if not, disregard this step.) a.Connect dim+ to fixture (purple) lead.
b. Connect dam- to fixture (gray) inad Dimming range for this fixture is 0-100%. -
Fix the bracket cover by screw (Fig.B).
-
Loosen screw and adjust the fixture to a desired illumination angle, then tighten screw (Fig.9).
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>