Xbuyee 300W LED Parking Lot Light Instruction Manual

June 15, 2024
Xbuyee

LED SHOEBOX/PARKING LOT LIGHT
SLIPFITTER
Model Number:300w

PACKAGE CONTENTS

Xbuyee 300W LED Parking Lot Light -

PART DESCRIPTION QUANTITY
A LeDAreaFixture 1PC
B1 Bracket Connector 1PC
B2 Slipfitter bracket 1PC
C Screw (1/2-1313/4″) 1PC
D Screw(5/16-18*1″) 4PCS
E Spring washer (5/16) 4PCS
F Flat gasket (5/16) 4PCS

Note: Hardware not wn to actual size.

SAFETY INFORMATION

WARNING: Risk of Fire, Electrical Shock, Cuts or other Casualty Hazards- Installation and maintenance of this product must be performed by a qualified electrician. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and hazards involved.

WARNING:To reduce risk of fire, electric shock, or injury to persons.

  • Risk of Fire and Electric Shock- Make certain power is OFF before starting installation or attempting any maintenance. Disconnect power at fuse or circuit breaker.
  • Risk of Burn- Disconnect power and allow fixture to cool before handling or servicing
  • Suitable for wet location and operation in temperatures not exceeding 122 “F/50C
  • For use in 100-277Vac application
  • Replace the lens if damaged
  • There are no serviceable parts inside the fixture.
  • Risk of Personal Injury- Fixture may become damaged and/or unstable if not installed properly. Failure to comply with these instructions may resultin death, serious bodily injury and property damage.

SAVE THESE INSTRUCTIONS. For safest operation, read and become familiar with complete installation instructions prior to use. Pay close attention to this manual and stay within its guidelines when using this product.
CAUTION:

  •  All parts must be used as indicated in this manual. Do not substitute any parts, leave parts out, or use parts that are worn out or broken. Failure to obey this instruction could invalidate the ETL certification
  • LEDSs emit bright light.Avoid looking directly at the light source.

PREPARATION
Before beginning assembly, installation, or operation of product, make sure all parts are present. Compare parts with package and hardware contents list on page 1. If parts is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for replacement parts.

INSTALLATION INSTRUCTIONS

  1. Put wire of the fixture A through bracket B1 (Fig.1).

  2.  install spring washer E & flat gasket F on screws and then Fix the bracket B1 on the fixture A with four screws D (Fig.2).
    Xbuyee 300W LED Parking Lot Light - Put wire

  3. Put wire of the fixture A through bracket B2 (Fig.3).

  4. Assemble the bracket B2 to the fixture A with screw C (Fig.4).

  5. AC Input Wiring (Fig.5).
    Connect fixture to supply wires:
    a.Connect supply line wire to fixture black lead
    b.Connect supply neutral wire to fixture white lead.
    c.Connect supply ground wire to fixture green lead.

  6. 0-10V Dimming Wiring (Fig.6).
    (Ifdimming, use with 0-10V dimming switch;
    if not, disregard this step.)
    a.Connect dim+ to fixture (purple) lead.
    b.Connect dim- to fixture (gray) lead.
    Dimming range for this fixture is 0-100%.

  7. Mount the fixture on the pole. Tighten the four fixing screws (Fig.7).The maximum pole diameter should be 2.38 inches.

  8.  Loosen screw C and adjust the fixture to a desired illumination angle, then tighten screw C  (Fig.8).

FOR PHOTOCELL

The fixture is equipped with dusk-to-dawn photocell.
To enable dusk-to-dawn operation, please remove the cover.
Also keep the cover for future use (Fig.10).
Note: When power is turned on, and the ambient light level is not low enough toactivate the photocell, luminaire will be in standby mode and give off a very dim glow.
This is normal operation. It consumes as little as 0.3W of energy in standby mode.

WATTAGE SWITCHABLE

The fixture is equipped with three working wattage options, 300w ←240w→200w.
The default wattage is 300W.To change it, please follow the steps below:

  1. Remove the cover by screwdriver (Fig.10).
  2.  Set the switch to the corresponding wattage position (Fig.11).
  3. Put the cover back and tighten it by screwdriver (Fig.12).

Xbuyee 300W LED Parking Lot Light - Put wire6

CARE AND MAINTENANCE

Use only a mild soap and/or water with a soft cloth to clean the fixture. Harsh chemicals will damage the fixture. Do not wipe the fixture with a rough cloth that may scratch the finish or the lens.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals