HTK SUCXDZQ Automatic Intelligent Toilet Instruction Manual

HTK SUCXDZQ Automatic Intelligent Toilet

Note: gearing and use before please to cautiously read this manual Please the warning and regulation of obeying the product manual inside marking

Safety directory

Please cautiously read before installing and using.

Warning-To avoid electric shock

1. Do not place the product where it may get wet.
2. Do not drop the remote control into the water.
3. Do not spray water into the product or plug.

Warning: To prevent the possibility of ,burns, electric shocks, fires and injuries.

1. Young children, temperature insensitive users, when using this product, should be accompanied by others. And turn off or lower the seat temperature.
2. The product is limited to the function on the manual, do not use other equipments.
3. Do not continue to use when the product is out of order, damaged or flooded. Please send the product to the designated repair center for repair.
4. Please make sure that the wires are not damaged by burning.
5. Do not use this product when you are out of your mind.
6. Do not plug the product or pipe.
7. Do not used outdoors.

Please be sure to observe the following

Please don’t sprinkle urine at the essence and spray.
Pull out the plug when it thunders.
Strictly forbid to directly flush with water.
Please do not wipe seat and cover with dry cloth or toilet paper.

Please do not open the seat ring or cover violently.

• May cause cracking or malfunction.

Please take antifreeze measures to prevent damage caused by freezing.

Please do not put heaters near this product.

• Discoloration or malfunction will occur

Safety Caution

Note: please cautiously read before using

Please read carefully before using. The cautions listed here are related to safety and please follow, &. This product is an electrical product. Please do not install it in a place where it is easy to be splashed by water or high humidity. When using in the bathroom, please install a vent to keep good air flow in the bathroom.

The socket for power distribution should be set as follows

•  The gearing position of electric outlet pleases to give examples 0.3 min the ground above, and leave bathtub as far as possible a little bit farer.
• The back track of electric outlet pleases use a high feeling and rapid type electric leakage switch(the sum certainly responds the electric current 15 mA following) or use to insulate the transformer 1.5 KVA above, the 3 KVA is following)carry on a protection .

The product connects a ground of line to carry on to connect a ground of processing, if has never carried on to connect a ground of processing, may arouses to get an electric shock.

Note: the grounding treatment mentioned here means that the grounding resistance is below 1000, and the grounding wires of the switchboard shall be copper wires with a diameter of more than 1.6mm.

While using in the bathroom please confirm the power plug have already used silica gel to carry on a waterproof processing.

Examples and illustrations of ICONS

|    it is not feasible (prohibited).
The socket for power distribution should be set as follows
The image on the left shows (disassembly is prohibited).

| Represents something that must be (enforced).The left hand diagram shows (must comply).

Must obey

| Notice heat burn

When the following occurs. please unplug

the power plug, close the Inlet Angle valve.

stop the inlet

ceramic WC is soaking

• Cracks appear
• Abnormal Sound and smell
• Fume-off
• Abnormal heating
• The toilet is clogged
• If continued under the condition of (failure it may cause fire, electric shock or indoor problems

Do not disassemble, repair or transform the product without permission

• It may cause a fire or electric shock

Do not Install this product In damp places such as bathrooms

• It may cause a fire or electric shock

Do not damage the Power cord or toilet seat cable.

• Don’t pull
• Don’t process
• Don’t heal
• Don’t forcibly bent
• Do not place heavy objects on the power cord and toilet seat connection line.
• May cause fire. electric Shock or sh0rt. circuit. If the power supply is damaged, please contact a professional for repair .

Do not use extension wires. otherwise, it may cause a fire or electric shock

• Do not connect wires or use extension cord s, which may cause fire and electric shock.

Do not use unhealthy water

• May cause skin lrrl1ation and other problems

---|---

Prohibit

| Do not continue to use the product when it breaks down

When the following occurs, please unplug the power plug, close the inlet Angle valve, stop the inlet.

• Ceramic WC is leaking
• Cracks appear
• Abnormal sound and smell
• Fume-off
• Abnormal heating
• The toilet is clogged
• If continued under the condition of failure, it may cause fire, electric shock or indoor seepage problems

Do not disassemble, repair or transform the product without permission

• It may cause a fire or electric shock

Do not install this product in damp places such as bathrooms

• It may cause a fire or electric shock

Do not damage the power cord or toilet seat cable

• Don’t pull
• Don’t Process
• Don’t forcibly bent
• Do not place heavy objects on the power cord and toilet seat connection line.
• May cause fire, electric shock or short circuit. If the power supply is damaged, please contact a professional for repair.

Do not use extension wires. otherwise, it may cause a fire or electric shock

• Do not connect wires or use extension cords, which may cause fire and electric shock.

Do not use unhealthy water

• May cause skin irritation and other problems

---|---

The first use of Intelligent toilet

Note: To ensure the normal use of the product, please follow the instructions to text.

1. lnsert the power plug into the AC (AC) 110V socket
2. Please confirm whether the indicator of the digital display panel is lit
3. Confirm whether the inlet valve is take on
4. Whether the hose between the wall Angle valve and the toilet inlet valve is installed in place
   

Caution-Confirmed matters before using

1. Check whether the sprinkler head and water pipe leak, dry all parts of the water pipe and check with blotting paper.
2. Press the seat around the seat sensor, whether there is a sound.
3. Check whether the cleaning, drying, automatic deodorization and automatic flushing are normal
4. Whether the Damped structure is normal.

Check the functions of cleaning, drying and automatic deodorization, make sure the sensor is on. When cleaning, cover and block the spray nozzle, so as not to splash.

Warning Be sure to firmly connect ground wires

The power plug of this product is a three-phase plug (with ground wire).
There is a danger of electric shock when there is a fault or leakage of electricity.
If there is no ground plug in the socket, consult with the electrical installation company.
Do not use power supply other than AC 220V/110V, please wiring according to relevant regulations.
Using the wrong power supply can easily cause fire

1.  Radar switches to foot cover: long press cover button on the remote control until it beeps;
2. Tum off I tum on the wall moistening function: tum off the power on the remote control, long press the fiush button; one beep means it is turned off and two beeps means it is turned on;
3. Tum off I tum on disseat water flushing: long press the fiush button; one beep means it is turned off and two beeps means it is turned on;
4. Tum off I tum on the function of flushing upon cover falling: turn off the power on the remote control, long press the cover button on the remote control; one beep means it is turned off and two beeps means it is turned on;
5. Tum on I tum off voice broadcast: press the stop button and energy saving button on the remote control at the same time

Instructions for remote control

Note: Please read the following carefully before use

his button is limited to induction turn flip design
Note: when used for the first time, it need match code if no response control code

power switch
Click this button to open or closed the machine power supply.

Match code of remote control
Long press implement side hip cleaning after three seconds after it take a sound, press any key, remote control of code completion

Full automatic flip
Click this button, the seat cover open automatically, and then press it again, the seat cover take off automatically

Automatic turn circle
Click this button, automatic seat open, press the button again, tile seat closed automatically.

Water temperature
Four gear can adjust the water temperature. The water temperature can be set for water no heating, Green is about 34°C,yellow is about 37°C,red is about 40°C

Seat temperature
Four seat temperature adjustable. Temperature can be set for the normal, Green is about 34°C yellow is about 37°C,red is about 40 C

Wind Temperature
Four gear can adjust the wind temperature. Temperature can be set for the normal, Green is about 34°C,yellow is about 37°C, red is about 40°C

Hip/spray moveable
Click this button, the hip wash nozzle will be in a fixed position to stop injection automatically after 2 minutes. Press this button again to clean mobile process

Female/spray moveable
Click this button, the female wash nozzle will be in a fixed position to stop spraying automatically after 2 minutes. Press this button again to clean mobile clean process

Drying
Seated then press this key, carries on the warm air drying, then it will automatically stop after 3 minutes

Flow regulating
Can increase or reduce the washing water pressure. Wash water pressure can be set for the weak, medium and strong, the strongest

Stop
Can stop the the running functions such as “hip/female cleaning” and “drying”

Flush
Click this button, start flushing function

Position adjust
Press this button when using the “hip/female cleaning” in the process of the injections, and can adjust the position of the nozzle forward or backward without using

Nozzle
Nozzle extended and water out for hand nozzle washing

Energy saving
Implement monitor or indicator lights work out, the toilet into intelligent power saving standby mode

Night light
In the boot state, can be opened and closed night light

The instructions on operation buttons

Seat former keys function
Power supply: open/ close the toilet
Hip/Female cleaning: adjust the water/seat temperature gear

After seated keys function
Power supply:( the stop button ) to stop the executing function
Hip cleaning/ female cleaning /drying: open the corresponding function
Flush: automatic flush toilet

Wall washing open/close: Press the toilet side keys “hip cleaning” and “flush” at the same time when toilet starts working

Description of other functions

• (Flushing by foot sensor ) Close to the foot sensor, turn on the scour function (manual clamshell)
  ( Open cover and seat by foot sensor ) Close to the foot sensor, automatically open/close cover and seat (automatic flip cover)

• ( Radar automatic clamshell function ) Close to the toilet, automatically open the cover, automatically close the cover after leaving and flush automatically (automatic flip cover)

Daily cleaning and maintenance

Note: During cleaning and maintenance, please be sure to unplug the power switch and power off

Smart toilet cleaning and maintenance methods

• Please wipe it with a soft cloth dampened with water
• If the dirt is not removed in time, it will become difficult to clean, please wipe with water sometimes.
• Static electricity will absorb dust, resulting in the product black, dirty, water wipe can prevent the generation of static electricity.
• The ceramic body can be removed from the toilet seat to facilitate cleaning between II ~ the toilet seat and the ceramic body.

Cleaning and maintenance of spray head

• If there is dirt in the nozzle. Please clean ii with a small brush such as a toothbrush.
• Do not stretch and bend the spray head.

Clean the dust on the power plug regularly

When cleaning, remove the power plug and wipe with a dry cleaning cloth.
Must obey – Poor insulation may cause a fire.

Common fault diagnosis

Note: If similar fault is found, please read the following solution or contact after sales

the circuit
whether there is leakage (the display light of the leakage protect plug is not on)| Remove the power plug from the socket and replug it later. press the release switch off the leakage protection plug. please unplug the power plug and interest the repair
No water with spray| Check if water is cut off| Pending resumption of water supply
Check that the Angle valve is closed| Open the Angle valve
Check if the inlet filter is blocked| Clean or replace the filter
Check the inlet pipe for bends| Exclude the intake bend
Cleaning insufficient rigidity| Check whether the cleaning pressure is at the lowest level| Refer to the instruction manual for regulating the water pressure
Check if the inlet filter is blocked| Clean or replace the filter
Spray water disorderly| Abnormal operation| Unplug the plug for one minute and then switch it back on
water temperature is not enough| Check that the water temperature is set low| Adjust the water temperature according to the instructions
Whether the hot and cold massage function is on| Turn off the hot and cold massage function according to the instructions
The washer often drips water| Solenoid valve failure| Please get professional maintenance technicians

Drying/seat temperature
too low/no heating| Check whether the temperature is set at low or normal temperature| Adjust the temperature according to the instruction
Whether to turn on the power saving function| Refer to the manual to choose to turn off

the power saving function

Seat/ cover falling too fast| Failure of damping drop function| Please get professional maintenance technicians
The cleaning function
cannot be used normally| Is there any other hard material holding it under the seat| Remove the hard objects
Whether the body’s sensing area is covered| Adjust the body sensing area of the seat cover
Whether the power supply is restored during the power failure| Unplug the plug for one minute and then switch it back on
The skin completely cover the human body induction area of the seat| Sensor failure, please get professional maintenance technicians
Low water pressure does not flush clean| Failure of automatic damping function|

1. Disconnect the plug for one minute and switch it back on
2. The above treatment is invalid, please ask professional personnel for maintenance

Filter mist blocking| Clean the filter according to the instruction
Pipe bending| Observe whether the connection line bends and keep the water supply line smooth
No siphon flushing is not clean when water pressure is normal| Air escapes from the sewage outlet| Please get professional maintenance technicians
The S-bend is blocked| Please buy water pipe dredger in the market for dredging
Flush is not clean when water pressure normal| Flush valve failure| Ask professionals for maintenance

Product standard

Due to the different printing time of the materials, the product specifications may be slightly changed. Please refer to the material object.

Water discharge: 750ml/min Power: 1350W
Cleaning| Water outlet| Hip cleaning| About 700 ml/min
Female cleaning| About 700 ml/min
Outlet water temperature| Normal temperature, and 34°C/37°C/40°C(4 grades)
Water heating| Instant water heater
Heater power| Water inlet temperature: 15°C , Outlet water temperature: 40°C Water discharge : 750ml/min Power: 1350W
Safety device| Water temperature sensor. Temperature blocking filament, Temperature controller, Leakage protector
Seat heating| Seat temperature| Normal temperature, and 34°C/37°C/40°C(4 grades)
Heater power| 40W
Safety device| Water temperature sensor, Temperature blocking filament
Warm drying| Wind temperature| Normal temperature, and 35°C/45°C/55°C(4 grades)
Air flow| >0.2m3/min
Heater power| 220W average(The maximum is about 350W)
Safety device| Bimetallic strip, Temperature blocking filament
Deodorize| Type| Activated carbon high efficiency filter
Mobile cleaning| The spray head can move 1.5cm forward and backward
Spray position| Adjustable Fore and Aft
Water temperature| 5- 40°
Water pressure| 0.15-0.75 Mpa (static) is about 5L of water in 15 seconds

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>