Fantech FKD..EC Series Inline Fan FKD EC Instruction Manual

Fantech FKD..EC Series Inline Fan FKD EC Instruction Manual

PARTS IN THE BOX

Inline Fan FKD EC, 1 pc
Electrical Box Hardware, 1 pc
Operation and Installation Manual, 1 pc

| | | |
---|---|---|---|---
Note| Warning / Important note| Information| Technical information| Practical tip

W
ARRANTY BY AN EXTRA YEAR

United States Tel.: 800 747 1762
Canada Tel.: 800 565 3548
Latinoamérica Tel.: +52 55 1328 7328

Fantech Inc. certifies that the FKD EC Series shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication 211 and AMCA Publication 311 and comply with the requirements of the AMCA Certified Ratings Program.

Before installation, servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

1. . The compactness and adaptability of the FKD..EC Series fans permit easy installation. The fans are shipped fully assembled and can be mounted at any angle. For various mounting, see figures on the following page.
2.  Because this unit has rotating parts, safety precautions should be exercised during all phases of installation, operation and maintenance.
3. CAUTION: “For General Ventilation Use Only. Do Not Use To Exhaust Hazardous Or Explosive Material and Vapors.”
4. Remove unit from package and inspect within 15 days after receipt. If damaged, report damage to carrier. Do Not operate this unit with visible damage to the blower or impeller assembly.
5. CAUTION : “This unit has an unguarded impeller. Do not use in locations readily accessible to people or animals.” WEAR HAND PROTECTION AND STAY CLEAR OF SHARP EDGES!
6.  Screen guards must be installed within reach of personnel, within (7) feet of the working area, or when advisable for safety.
7.   PLEASE read the entire manual before installing.

WARNINGS

Do not connect power supply until fan is completely installed. Make sure electrical service to the fan is in the locked “OFF” position.

1. Three phase units must be wired through a motor contactor.

2. WARNING! TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS – OBSERVE THE FOLLOWING :
   a. Use this unit in the manner intended by the manufacturer. If you have any questions, contact your manufacturer’s representative or contact us directly.
   b. CAUTION: Before installation, servicing or cleaning unit, switch power off at service panel and lock the service disconnection means to prevent power from being switched on accidentally. When the service disconnection means cannot be locked, securely fasten a prominent warning device, such as tag, to the panel.
   c. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.

3. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Association (NFPA), and the American Society for Heating, Refrigeration and Air-Conditioning Engineers (ASHRAE), and the local code authorities.
   a. When cutting or drilling into wall and ceiling, do not damage electrical wiring and other hidden utilities.
   b. Ducted exhaust fans must always be vented to the outdoors.
   c. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application and be connected to a GFCI (Ground Fault Circuit Interrupter) – protected branch circuit.
   d. Use only on GFCI Protected Receptacles.
   e. Do not use an extension cord with this fan.
   f. If a power cord is connected, do not install this fan behind a suspended or structural wall, ceiling, or floor. g. NEVER place a switch where it can be reached from a tub or shower.

4. WARNING! Check voltage at the fan to see if it corresponds to the motor name plate.

INSTALACION 1

INSTALACION 2

Please follow all applicable codes when installing this unit

1. Equipment should be hung at its proper elevation by using temporary
   fixtures that can be removed after vibration hangers are installed. (Vibration isolation mounts provided by others)

2.  Hanger may be fastened directly to the structure or somewhere between suspended unit (be sure not to over tighten the neoprene element).

3. Install hangers.

4. Turn nuts on rod assembly clockwise one complete turn on each hanger. Repeat this procedure until temporary hanging fixtures are loose and load of piping or equipment is suspended completely on the vibration hangers.

5. Remove temporary hanger fixtures and level piping or equipment by taking additional turns on the spring/top hanger rod nut – clockwise to raise, counterclockwise to lower as required.

6. If equipping fan with isolators (FC Clamps), they should be attached at this time.

7. See wiring section to complete installation

INSTALACION 3

lease follow all applicable codes when installing this unit

1.  Create/Install angle wood supports to structure for fan mounting.
2.  If equipping with vibration mounts, attach to supports.
3. Attach fan to vibration mounts, supplied by others (be sure not to overtighten the neoprene element).
4. If equipping fan with isolators (FC Clamps), they should be attached at this time.
5. See wiring section to complete installation. Vibration

Mounts and Hardware are not supplied with fan. FC Clamps are sold separately

DIMENSIONES

FKD 12XL-EC

Model / Modèle / Modelo| A| A1| A2| B| C| D| E| F| G| H| Weight / Poids / Paso
---|---|---|---|---|---|---|---|---|---|---|---
FKD 12XL-EC| 12| 12| 14| 201/4| 177/8| 187/8| 7/8| 4| 83/4| 3/8| 38
FKD 14XL-EC| 14| 14| 16| 221/8| 193/4| 201/4| 1 1/2| 4| 8 3/4| 3/8| 45
FKD 16-EC| 16| 14| 16| 221/8| 193/4| 183/4| 1 1/2| 4| 71/8| 3/8| 75
FKD 16XL-EC| 16| 16| 18| 243/8| 221/8| 233/4| 1 1/4| 77/8| 81/2| 1/2| 75
FKD 18-EC| 18| 18| 20| 283/5| 261/9| 271/5| 1 1/4| 77/8| 7| 1/2| 98
FKD 20-EC| 20| 18| 20| 283/5| 261/9| 271/5| 2| 77/8| 121/2| 1/2| 99

All dimensions are in inches and weights are in pounds

CABLEADO

Single Phase Fans FKD 16-EC
Motor Cables

Fantech reserves the right to make technical changes. For updated documentation please refer to www.fantech.net

1. Wiring
2. White
3. Green Vert Verde,
4. Brown
5. Blue
6. Yellow
7. Red
8. Black

WARNING
Maximum torque that can be applied to the terminal block screws is 0.79 Nm (7 lb-in).

Make a scan of the code above to access Fantech’s warranty in English, French, or Spanish

If additional support is needed to retrieve the warranty, visit fantech.net; call (800) 747–1762 (US), (800) 565–3548 (Canada), or +52 55 1328–7328 (Latin America); email support@fantech.net; or mail us at 10048 Industrial Blvd, Lenexa, KS 66215 United States or at 50 Kanalläkt Way, Bouctouche, NB E4S 3M5 Canada

References

• We simplify ventilation solutions | Fantech
• We simplify ventilation solutions | Fantech

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>