Stone Mountain BS-OM-A3 BluSkye Bluetooth Speaker Microphone User Manual

Stone Mountain Blu Skye ® Bluetooth® Speaker Microphone (SM) User Manual Rev. BS-OM-A3
Blu Skye® is a feature rich, industrial grade Bluetooth® speaker microphone that supports Android, Windows

and LMR platforms running Push To Talk (PTT) applications. SM buttons may have different assigned functions by the PTT OEM than those shown below – Read your PTT application and/or Device manual for further information.

Starting Out

1. Charge the SM for at least six (6) hours prior to first use. When the SM is powered off, there is no LED charging indication, though charging is still occurring. Note: Be sure to only charge with Stone Mountain approved charging accessories.

Note 1, 2
5| SW5| Not used/no function|
6| SW6| On/off, pairing, configuration, etc.|
7|  | 3.5mm Rx Audio Port|
8|  | Tru Dock TM cradle contacts|
9|  | 5.5mm charging port|
10|  | LED indicator|

Notes

1. Buttons may have different functions depending upon the PTT Refer to your PTT app and/or Device user manual for further details.
2. Function dependent upon

1.0 Basic Operating Instructions

• Power On: While the unit is off, press and hold SW6 for three A low-mid two-tone beep and two

blue LED flashes will occur powering on the Device.

• Power Off: Press and hold SW6 for three One beep will occur for each second held to alert you the SM will power off. The unit will emit a mid-low two-tone beep and the LED will flash red twice as it powers off. If the button is released before three seconds have passed, the SM will not power off.

1.3    Pairing:

• Confirm the SM is powered
• Press and hold SW6 for 6 seconds. After emitting a mid-high two-tone beep and constant

red / blue flashing from LED on the rear cover the SM will enter pairing mode.

• Once in pairing mode, follow pairing instructions from the host Device you are pairing the SM

• When successfully paired to host Device, the SM will generate a two tone beep and maintain a constant blue flashing from the LED.

• LED Signals

flashes

Connected| One blue flash every three seconds
Powered On, Not Connected| One red flash every three seconds
Boot Sequence| Two sets of red , blue , and green

flashes

Low Battery| One yellow flash added to the

current state of the unit

Charging| One green flash added to the current

state

Charging status will not be displayed while the SM is powered off

• Button Functionalities:
• PTT Call :
• Press and hold SW2 to Tx (Transmit) a call This requires a compatible Device (tablet, smartphone, radio, Windows platform).

1.5.2   Emergency Operation:

• Depending on your Device and/or PoC app, SW1 can be designated as an Emergency/SOS Button.

1.5.3 Volume Control:

• There are 10 volume To increase volume , press and hold SW3. The volume level will increase and will beep once for each setting increase until the maximum level is reached.
• To decrease volume , briefly press and release SW3. Each press/release of the button will decrease the volume level by one step and will beep once at each step until the minimum level is reached.

1.5.4 Phone Call Control:

• To answer an incoming call in supported configurations, briefly press and release SW4. To reject an incoming call, hold SW4 for at least one (1) second. To end an ongoing call, briefly press/release SW4.
• The default routing for call audio/voice can be set in the paired Device’s
• In the Settings app, select “ Connected Devices ”. Select the options for the

paired SM (usually denoted by a gear) and enable or disable phone calls.

1.5.5  Battery Life and Monitoring:

• There is a low battery audible beep/ red LED flash that occurs every thirty (30) minutes when the battery gets to 15% At this point, the SM should be recharged as soon as possible.
• To recharge the SM, remove the protective rubber plug from the charging port. Plug the 5mm connector of a Stone Mountain approved charger into the charging port. The SM LED will flash green while charging when the SM is powered on. Full charge takes between 5 to 6 hours assuming a completely discharged battery. Replace the protective rubber plug after charging is complete.
• The SM can also be charged in optional Tru Dock ™ single bay, vehicle mount and gang chargers.

1.5.6 Hard Reset:

• In the event a Hard Reset is required, press and hold SW2 and SW6 simultaneously for (4) seconds. The SM will undergo its boot sequence and power down upon completion. The SM should resume normal function at the next Power On

1.5.7  Care & Maintenance:

• Do not use solvents, abrasive, or other cleaning solutions to clean your Blu Skye®.

Clean with mild soap and tap water.

• Do not insert objects into the speaker chamber or the microphone port, as this will adversely impact the audio quality and subsequent water leakage.
• Use only Stone Mountain approved chargers to recharge your Blu Skye®.

2.0 Adding Blu Skye ® to Android Devices

• Adding your Blu Skye ® Button:
• Make sure you’ve paired your SM through Android Refer to 1.3 of the User Manual for instructions on pairing the SM.
• Search for Stone Mountain BluSkye PTT , connect, and press done. The SM will create a two- tone beep and the LED on the back of the unit will continue to blink blue every 3 Refer to images below.

3.0Checking and Changing Configurations

3.1    To check the configuration of your Blu Skye ®

• The SM comes factory configured. To check the configuration, ensure the SM is powered Press and hold SW2 and SW6 for eight (8) seconds. The LED will flash pink. Next will be some number of BEEP ’s that correspond to the SM’s present Configuration Number , e.g.:
• 1 BEEP /1 red LED flash = Configuration 1.
• 2 BEEP /2 red LED flash = Configuration 2 , and so

This is followed by a BEEboop, boopboopboop , BEEboop , at which time, Configuration Mode is exited. The SM is now powered off and unpaired. Follow the Pairing Instructions to turn on and re-pair the SM to the Device.

3.2  To change the configuration of your Blu Skye ®:

• It is not recommended to change the Configuration from the factory setting unless absolutely necessary. Reference the table below. Follow the Check Configuration After the audible Configuration Number BEEP (s) and before the exit Configuration Mode tone, press SW6 the number of times corresponding to the desired configuration. An audible BEEP (s)/ red LED flash(es) will follow confirming the new Configuration number. This is followed by an audible BEEboop, boopboopboop , BEEboop , at which time, Configuration Mode is exited. The SM is now powered off and unpaired. Follow the Pairing Instructions to turn on and re-pair the SM to the Device.

Configuration.

Number

| Application / Device| Top Button (SW1)

Function

| Programmable Button (SW4)

Function

---|---|---|---
3| Sonim| PTT| Call accept/end/reject
6| Harris/BK LMR| Emergency| No function
7| Windows PC| PTT| No function
10| ICOM LMR| Emergency| No function
11| Harris BeOn| Emergency| No function
14| Zello, ESChat & other major PTT apps| Emergency| Call accept/end/reject
16| Zello, ESChat & other major PTT apps| Emergency| App Dependent

Innovation… Quality… Passion

Designed, Assembled, Tested and Supported with Pride in the USA, at Stone Mountain we strive to provide our customers with innovative products of the highest quality, reliability, and value. We welcome and appreciate your input – Feel free to contact us

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>