Shaw Business CGNM-2250 Hitron Modem User Guide

Shaw Business CGNM-2250 Hitron Modem

Product Information

Specifications

• Model: CGNM-2250
• Brand: Hitron

Product Usage Instructions

How to login to your Hitron Modem:

1. Connect your modem directly to your computer using an Ethernet cable.

2. Open an Internet browser (Internet Explorer, Firefox, Chrome, Safari) on your computer.

3. Enter the following into the address bar:
   http://192.168.0.1

4. Press the ENTER key on your keyboard.

5. You will then be taken to the Hitron Advanced WiFi modem’s sign-in page where you can sign in.

6. Click “Login”.

Advantage WiFi and LAN setup:

The diagram below illustrates the network topology for Advantage WiFi:
The Advantage WiFi access points (the APs that broadcast the Private, Guest, and Rogers WiFi Hotspots SSIDs) connect directly to the Hitron Modem. The customer’s Local Area Network (LAN) connects here as well.

LAN Setting – Private Gateway IP and Dynamic Host Configuration Protocol (DHCP)
To adjust these LAN configuration settings:

1. In a browser window, log in to the Hitron Modem user portal by entering http://192.168.0.1.
2. From the top navigation bar, click “Basic” and then “LAN Setup”.
3. Input the desired IP Address into the “Private LAN IP Address” text field. This IP Address will be the new Gateway IP Address for Graphical User Interface (GUI) logins.
4. Input the Subnet Mask into the “Subnet Mask” text field. The Subnet Mask entered will define the DHCP scope the Hitron will use to offer IP addresses to clients (most setups will simply use 255.255.255.0).
5. Confirm that LAN DHCP Status is enabled.
6. Select the desired DHCP Lease Time with the drop-down menu. This specifies how long the IP address can be leased before it resets.
7. Input the first available LAN IP Address that will be assigned by DHCP to clients into the “DHCP Start IP” text field.
8. Input the last available LAN IP Address that will be assigned by DHCP to clients into the “DHCP End IP” text field.
9. Click “Save Changes” to save the new changes you have made.

DHCP Reservation
To add a DHCP Reservation:

1. In a browser window, log in to the Hitron Modem user portal by entering http://192.168.0.1.
2. At the top of the page, click “Basic” and then “LAN Setup”.
3. Click “DHCP Reservation”.
4. Add a DHCP Reservation from the DHCP Table.

FAQ

Q: How do I access the configuration settings for the Hitron modem?
A: To access the configuration settings for the Hitron modem, first connect your modem directly to your computer with an Ethernet cable. Then follow these steps:

1. Open an Internet browser (Internet Explorer, Firefox, Chrome, Safari) on your computer.

2. Enter the following into the address bar:
   http://192.168.0.1

3. Press the ENTER key on your keyboard.

4. You will then be taken to the Hitron Advanced WiFi modem’s sign-in page where you can sign in.

5. Click “Login”.

How to login to your Hitron Modem

To access the configuration settings for the Hitron modem, first connect your modem directly to your computer with an Ethernet cable. Then follow these steps:

1. Open an Internet browser (Internet Explorer, FireFox, Chrome, Safari) on your computer.
2. Enter the following into the address bar: http://192.168.0.1
3. Press the ENTER key on your keyboard.
4. You will then be taken to the Hitron Advanced WiFi modem’s sign in page where you can sign in with the following information:
   • Username: cusadmin
   • Password: This is listed as the “WiFi Key” on front of your Hitron Modem
5. Click Login

The following screenshot is what you will see upon login to the Hitron Modem user portal. The setting options you will select from are either at the top or on the right of the portal page.

Advantage WiFi and LAN setup

The diagram below illustrates the network topology for Advantage WiFi:

• The Advantage WiFi access points (the APs that broadcast the Private, Guest, and Rogers WiFi Hotspots SSIDs) connect directly to the Hitron Modem. The customer’s Local Area Network (LAN) connects here as well.
• The following sections indicate how to set up the different Gateway/router functions of the Hitron Modem to interact properly with your LAN.

LAN Setting -Private Gateway IP and Dynamic Host Configuration Protocol (DHCP)
These settings will allow you to configure the Gateway IP and DHCP settings when you prefer a different IP subnet on your LAN other than 192.168.0.x or wish to limit the IP range that is available in the dynamic pool (the available IPs that can be assigned to a device). For example, you can set the dynamic pool to start at 192.168.0.100 and end at 192.168.0.255. Which reserves 192.168.0.2 – 192.168.0.99 available for static assignment within the LAN. You can assign specific reserved IP addresses to a specific device such as a printer, server, backup drive, computer, etc.

Note: The IP range can be changed if needed.

To adjust these LAN configuration settings:

1. In a browser window, log in to the Hitron Modem user portal. See section 1 for details. The default is http://192.168.0.1
2. From the top navigation bar, click Basic then LAN Setup.
3. Input IP Address into Private LAN IP Address text field.
   • The IP Address entered will be the new Gateway IP Address for Graphical User Interface (GUI) logins.
4. Input Subnet Mask into Subnet Mask text field.
   • The Subnet Mask entered will define the DHCP scope the Hitron will use to offer IP addresses to clients. (most setups will simply use 255.255.255.0)
5. Confirm that LAN DHCP Status is Enabled.
6. Select desired DHCP Lease Time with the drop down menu. This specifies how long the IP address can be leased before it resets.
7. Input IP Address into DHCP Start IP text field. This defines the first available LAN IP Address that will be assigned by DHCP to clients.
8. Input IP Address into DHCP End IP text field. This defines the last available LAN IP Address that will be assigned by DHCP to clients.
9. Click Save Changes to save the new changes you have made.

Static DHCP Assignment – Add, Remove, View

• Through DHCP, the Hitron Modem automatically provides IP addresses to devices when they connect to the network.
• Using the Static DHCP assignment, you can ensure that a device connecting to the network gets the same IP address every time without having to hardcode that IP on the device. This is useful for things like your printer, a server, a backup drive or a computer where the IP address needs to be constant for easy accessibility.

To add or view a DHCP Reservation, follow these steps:

1. Access the DHCP Reservation Screen
   • In a browser window, log in to the Hitron Modem user portal. See section 1 for details. The default is http://192.168.0.1
   • At the top of the page, click Basic then LAN Setup.
   • Click DHCP Reservation.

Add a DHCP Reservation
Once you click on DHCP Reservation, the following window will pop up. You will then have two options to add a DCP Reservation:

Adding DHCP Reservation from DHCP Table

• Within the top section, Clients from DHCP Tables, locate the client name within in the list provided.

If your client is not in the list provided, click Refresh.

• Click Add, to add the reservation.
• You should now see the client listed under Client Already Reserved.
• Click Save Changes. You will see a warning prompt, read the warning prompt and click OK to make the changes.

Manually adding DHCP Reservation

• Within the second section, Manually Add Client, input desired client name into the Enter Client Name text field.
• Input IP Address into the Assign IP Address text field.
• Input MAC Address into the To this MAC Address text field.
• Click Add.
• You should now see the client listed under “Client Already Reserved.”
• Click Save Changes. You will see a warning prompt, read the warning prompt and click OK to make the changes.

To remove a DHCP Reservation, follow these steps:

1. Within the bottom section, Client Already Reserved, locate the target client you wish to remove.
2. Click Remove.
3. You should no longer see the client listed under Client Already Reserved.
4. Click Save Changes. You will see a warning prompt, read the warning prompt and click OK to make the changes.

Basic Setup of the Hitron Modem

Setting Public Static IP on Gateway of the Hitron Modem
This will be needed when you request a static IP address from Rogers Business. To request this, please call the Rogers Business Technical Support team at 1-877-742-9249. Once this is requested, you will receive an email with details for configuring the settings in your Hitron Modem.

Static IPs are most commonly used for running internet-facing servers. If you assign a static IP address to the Hitron Modem’s gateway, you will need to use port forwarding or a demilitarized zone (DMZ) to pass data from the static IP address to your server(s). Static IP Configuration requires 2 steps, making changes to the WAN and then to the Domain Name System (DNS) screen. Please Note: Though there will be overlap between some fields in the WAN and DNS screens, changes must be made in both sections.

To make adjustments to the WAN and DNS screen, follow these steps:

1. Configuring the WAN screen
   • In a browser window, log in to the Hitron Modem user portal. See section 1 for details. The default is http://192.168.0.1
   • At the top, click Basic then on the WAN Setup tab.
   • For Assign WAN IP Automatically(DHCP), click Disabled.
   • Input IP Address into the WAN IP Address text field.
   • Input Subnet Mask into the Subnet Mask text field.
   • Input IP Address into the Gateway IP Address text field. A gateway is a device on a computer network, a key stopping point for data on its way to or from the Internet. It routes traffic from a workstation to the outside network that is serving up the web pages.
   • Input IP Address into the Primary DNS Server text field.
   • Input IP Address into the Secondary DNS Server text field.
   • Click Save Changes. You will see a warning prompt, read the warning prompt and click OK to make the changes.
2. Configuring the Domain Name System (DNS) screen
   • At the top navigation bar, click Basic then on the DNS tab.
   • For DNS Obtain, click Manual.
   • Input IP Address into the DNS1 text field.
   • Input IP Address into the DNS2 text field.
   • Click Save Changes. You will see a warning prompt, read the warning prompt and click OK to make the changes.

Note:
IP Addresses for DNS1 and DNS2 must match the IP Addresses entered in the previous section (Primary DNS Server, Secondary DNS Server).

How to reset default settings of the Hitron Modem
If you need to restore your modem to default settings, you can do so by performing a pin-hole reset. To do this, locate the pin-hole reset button on the back of your modem and then push and hold it down with a paperclip or pen for fi ve to ten seconds. If completed successfully, the lights on the modem will begin to fl ash and the modem will take approximately two minutes to reset.

Please Note:
This reset will delete all of your custom confi gurations, including any changes you made to your SSID, network password and wireless channel settings.

Advanced setup

Port-Based IP Passthrough
Enabling Port-based IP Passthrough allows one or more ports on the Hitron Modem to bypass the Hitron DHCP. This would allow any device connected to a specific port to receive an external public IP.

To configure the Port-based IP Passthrough settings, follow these steps:

1. In a browser window, log in to the Hitron Modem user portal. See section 1 for details. The default is http://192.168.0.1
2. At the top of the navigation bar, click Admin then IP Passthrough.
3. For IP Passthrough Enable, click ON.
4. For IP Passthrough Mode, click Port.
5. Select the desired port for IP Passthrough Port.
6. Click Save Changes. You will see a warning prompt, read the warning prompt, and click OK to make the changes. The router will reset and you may need to wait a few minutes for connectivity to restore.

MAC-Based IP Passthrough
The Media Access Control address (MAC address) of a computer is a unique identifier assigned to network interfaces for communications. MAC addresses are used as network addresses for most IEEE 802 network technologies, including Ethernet and WiFi. Enabling MAC-based IP Passthrough allows a device on the network to obtain a public IP address based on its MAC address.

To configure the MAC-based IP Passthrough settings, follow these steps:

1. In a browser window, log in to the Hitron Modem user portal. See section 1 for details. The default is http://192.168.0.1
2. At the top of the navigation bar, click Admin and then on the IP Passthrough tab.
3. Click ON for IP Passthrough Enable.
4. Click MAC for IP Passthrough Mode.
5. Input MAC Address into the IP Passthrough MAC text field.
6. Click the + Icon to add an additional MAC address. Repeat Steps 5 – 6 for each additional MAC Address.
7. Click Save Changes. You will see a warning prompt, read the warning prompt and click OK to make the changes. The router will reset and you may need to wait a few minutes for connectivity to restore.

Port Forwarding
Port forwarding allows traffic or communication flow requests from a specific port(s) associated with an IP address of a host to be directed to a specific destination (IP address) on the internal network. For example, a security camera which uses port 56000. First, perform a DHCP reservation (please refer to the section 2a above, LAN Setting – Private Gateway IP and Dynamic Host Configuration Protocol (DHCP) and assign a static internal IP for the security camera (ex. 192.168.0.210). Then, forward port 56000 to 192.168.0.210. The Hitron will direct any traffic from a public IP address and port 56000 to the destination that was set (in this case 192.168.0.210).

To enable or disable Port Forwarding, follow these steps:

1. In a browser window, log in to the Hitron Modem user portal. See section 1 for details. The default is http://192.168.0.1
2. At the top of the navigation bar, click Basic and then on the Port Forwarding tab.
3. Click Enabled under All Port Forwarding Rules to Enable Port Forwarding.
   • To Disable Port Forwarding, click Disabled.
4. Under Port Forwarding Rules, click ON or OFF to enable or disable individual port forwarding rules.
5. Click Save Changes. You will see a warning prompt, read the warning prompt and click OK to make the changes. The router will reset and you may need to wait a few minutes for connectivity to restore.

Add a Port Forwarding Rule
Adding a port forwarding rule requires 2 steps:

1. Add a Rule
   • In a browser window, log in to the Hitron Modem user portal. See section 1 for details. The default is http://192.168.0.1
   • At the top of the navigation bar, click Basic and then on the Port Forwarding tab.
   • Click Add Rule.
2. Create a Rule
   • A box will pop up. Under the Common Application section, you can select in the drop-down menu predefined port forward rules for common applications.
   • Input or Edit the Application Name text field.
   • Select the desired Protocol with the drop-down menu.
   • Input Port Numbers into the Public Port Range text field.
   • Input Port Numbers into the Private Port Range text field.
   • Input IP Address into Local IP Address text field. This Local IP must be in the same LAN IP Address Subnet.
   • Select Any or Specific under Remote IP Address.
   • If Specific is selected, input a Public IP Range into the fields, ie. 68.59.141.110 – 68.59.141.110
   • Click Apply.
   • Click Save Changes. You will see a warning prompt, read the warning prompt, and click OK to make the changes. The router will reset and you may need to wait a few minutes for connectivity to restore.

Edit/Remove a Port Forwarding Rule
Deleting a port forwarding rule requires you to simply click Remove next to the rule to delete.

To edit a port forwarding rule, there are two options:

1. To remove the rule
   • In a browser window, login to the Hitron Modem user portal. See section 1 above for details. The default is http://192.168.0.1
   • At the top of the navigation bar, click Basic and then on the Port Forwarding tab.
   • Click Remove for the appropriate port forwarding rule.
   • Click Save Changes. You will see a warning prompt, read the warning prompt and click OK to make the changes. The router will reset and you may need to wait a few minutes for connectivity to restore.
2. Modify the rule
   • In a browser window, login to the Hitron Modem user portal. See section 1 above for details. The default is http://192.168.0.1
   • At the top of the navigation bar, click Basic and then on the Port Forwarding tab.
   • To Edit a Rule, click Manage for the appropriate port forwarding rule.
   • Modify the required parameters, similar to when the rule was initially created. For information on adjustable parameters, see the section above, i. Add a Port Forwarding Rule, 2. Create a Rule
   • Click Save Changes. You will see a warning prompt, read the warning prompt, and click OK to make the changes. The router will reset and you may need to wait a few minutes for connectivity to restore.

The Demilitarized Zone (DMZ)
The DMZ will allow you to forward all traffic from the IP of the Hitron Modem’s gateway to a specific machine behind the modem. The DMZ network is where all internet-facing servers in your network should be housed. Examples of such servers include a website you host from a web server in your business or your email server. The DMZ separates these Internet-facing servers away from your LAN.

• To specify a device as a DMZ host, follow these steps:

1. In a browser window, log in to the Hitron Modem user portal. See section 1: How to Login to your Hitron Modem for details. The default is <http://192.168.0.1>
2. At the top of the navigation bar, click Basic and then on the DMZ tab.
3. Click Enabled for Enable DMZ.
4. Input the IP Address into the DMZ Host text field.
5. Alternatively, you can click Connected Devices and select a currently connected host.
6. Click Save Changes. You will see a warning prompt, read the warning prompt and click OK to make the changes. The router will reset and you may need to wait a few minutes for connectivity to restore.![Shaw-Business-CGNM-2250-Hitron-Modem-fig- \(18\)](https://manuals.plus/wp-content/uploads/2023/12/Shaw-Business-CGNM-2250-Hitron-Modem-fig-18.png)

• To disable or modify the DMZ host, follow these steps:

1. In a browser window, login to the Hitron Modem user portal. See section 1: How to Login to your Hitron Modem above for details. The default is <http://192.168.0.1>
2. At the top of the navigation bar, click Basic and then on the DMZ tab.
3. Now, you have two options:
  1. To modify the DMZ host, input new IP Address into the DMZ Host text field. Alternatively, you can click Connected Devices select a new currently connected host.
  2. To disable the DMZ host, click Disabled for Enable DMZ.
4. Click Save Changes. You will see a warning prompt, read the warning prompt and click OK to make the changes. The router will reset and you may need to wait a few minutes for connectivity to restore.![Shaw-Business-CGNM-2250-Hitron-Modem-fig- \(19\)](https://manuals.plus/wp-content/uploads/2023/12/Shaw-Business-CGNM-2250-Hitron-Modem-fig-19.png)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>