iDTRONIC ID IDENT 2000 RFID and Barcode Reader User Guide
- June 15, 2024
- IDTRONIC
Table of Contents
- Disclaimer
- Preface
- Product introduction
- Product feature
- Product appearance
- OVERALL INTRODUCTION
- PRODUCT SIZE
- Parameters
- General parameter
- Electric parameter
- Interface definition
- Device configuration
- Mounting method
- Attention
- Contact info
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
iDTRONIC ID IDENT 2000 RFID and Barcode Reader User Guide
Disclaimer
Before using the product, please read all the contents in this Product Manual carefully to ensure the safe and effective use of the product. Do not disassemble the product or tear up the seal on the device by yourself, or iDTRONIC will not be responsible for the warranty or replacement of the product.
The pictures in this manual are for reference only. If any individual pictures do not match the actual product, the actual product shall prevail. For the upgrade and update of this product, iDTRONIC reserves the right to modify the document at any time without notice.
Use of this product is at the user’s own risk. To the maximum extent permitted by applicable law, damages and risks arising from the use or inability to use this product, including but not limited to direct or indirect personal damage, loss of commercial profits, iD TRONIC. will not bear any responsibility for trade interruption, loss of business information or any other economic loss.
All rights of interpretation and modification of this manual belong to iD TRONIC
Preface
Thank you for using the ID IDENT 2000 QR code reader provided by iD TRONIC. Reading this document carefully can help you understand the functions and features of this device, and quickly master the use and installation of the device.
Product introduction
The ID IDENT 2000 QR code reader was a specially designed embedded type device, which has various output interface, including USB, RS232, RS485, TTL, Wiegand, suitable for access control, turnstiles.
Product feature
- Scan code& swipe card all in one.
- Fast recognition speed, high accuracy, 0.1 second the fastest.
- Easy to operate, humanized configuration tool, more convenient to config the reader
Product appearance
OVERALL INTRODUCTION
PRODUCT SIZE
-
Front view
-
Bottom view
-
Side view
Parameters
General parameter
General parameter
output interface| USB, RS232, RS485, TTL, Wiegand
indicating method| Red, green, white light indicator Beeper
imaging sensor| 300,000 pixel CMOS sensor
max. resolution| 640*480
mounting method| embedded mounting
product dimensions| 88,3 x 88,3 x 28,35 mm
reading window size| 56 x 51 mm
Reading parameter
QR code recognition parameter
symbiology’s| QR, PDF417, CODE39, CODE93, CODE128, ISBN10, ITF, EAN13,DATABAR,
AZTEC, etc
supported decoding| mobile phone screen/ printed barcodes
reading distance| 0 mm – 62,4 mm (QRCODE: 15 mil)
reading accuracy| > 8mil
reading speed| 70ms per time (average), support reading continuously
reading direction| Tilt ±56,3° rotation ±360° deflection ±55,7°(15milQR)
FOV| Horizontal 72,1 ° vertical 56,6° FOV 84,3°(15milQR)
RFID parameter
type| ISO 14443A, ISO 14443B protocol
operation method| read UID, read the sector of M1 card
frequency| 13.56 Mhz
distance| < 5cm
Electric parameter
The power input can be provided only when the device is connected properly. If the device is plugged in or unplugged while the cable is live (hot plugging), its electronic components will be damaged. Make sure that the power is turned off when plugging and unplugging the cable. Poor power supply, too short interval power off and on operation may cause the device cannot work in a stable and normal status. It is necessary to keep the power input stable. After turning off the power input, it need to takes more than 2 seconds to turn on the power input again
Electric parameter
working voltage| DC 5V – 24V
working current| 200mA (5V typical value)
power consumption| 1W (5V typical value)
Working environment
work environment parameter
ESD protection| ±8kV (air discharge) ±4kV (direct discharge)
working temperature| -20°C – 70°C
storage temperature| -40°C – 80°C
relative humidity| 5% – 95% (no condensation, environment temperature)
ambient light| 0-100000 Lux (Non direct sunlight)
Interface definition
Pin Nr. | Definition | Description |
---|---|---|
1 | TTL_RX | TTL receiving end |
D0 | Wiegand 0 | |
2 | TTL_TX | TTL sending end |
D1 | Wiegand 1 | |
3 | GND | Ground |
4 | VCC | Power source |
5 | 232_RX | 232 receiving end |
485A | 485 PIN | |
6 | 232_TX | 232 sending end |
485B | 485 PIN | |
7 | DM | USB_data- |
8 | DP | USB_data+ |
Device configuration
Use the Voguing Config tool to configure the device, which can be download from our official website Configure the server address as the step shows:
Step 1: select language and device.
Step 2: select the output interface, and config the corresponding serial
parameters.
Step 3: config as your needs.
Step 4: after config as your needs, click “config code”
Step 5: use the scanner to scan the configurations QR code generated by
the tool, then restart the reader to finish the new configurations
For more information about the configuration tool, please refer to the Voguing Config user manual.
Mounting method
The product using CMOS image sensor, the recognition window should avoid direct sun or other strong light source when install the scanner. The strong light source will cause the contrast in the image too big to decoding, the long term exposure will damage the sensor and cause the device failure.
The recognition window are using tempered glass, which has good transmission of the light, it also a pressure resistance, but still need to avoid scratching the glass by some hard object, it will affect the QR code recognition performance.
The RFID antenna was in the underside of the recognition window, there should have no metal or magnetic material within 10cm when installing the scanner, or it will affect the card reading performance.
-
plug the cable to the reader.
-
install the holder on the 86 box, tighten with screws.
-
install the reader on the holder, push to the end.
-
installation completed.
Attention
- The equipment standard is 5-24V power supply, it can get power from the access control power or power it separately. Excessive voltage may cause the device to fail to work normally or even damage the device.
- Do not disassemble the scanner without permission, otherwise the device may be damaged.
- The installation position of the scanner should avoid direct sunlight. Otherwise, the scanning effect may be affected. The panel of the scanner must be clean, otherwise it may affect the normal image capture of the scanner. The metal around the scanner may interfere with the RFID magnetic field and affect card reading.
- The wiring of the scanner must be firm. In addition, ensure the insulation between the lines to prevent the equipment from being damaged by a short circuit.
Contact info
ide TRONIC GmbH Ludwig-Reichlin-Strafe 4 67059 Ludwigshafen Germany
E-Mail : info@idtronic-wellfit.de
Web: www.idtronic-wellfit.de
Phone: +49 621 6690094-0
Fax: +49 621 6690094-9
References
- Drehsperren, Speed Gates, Spindschlösser
- Drehkreuze, Spindschlösser, Zutrittsleser und mehr | iDTRONIC
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>