Emos ZT1040 LED Dustproof Luminaire User Manual
- June 15, 2024
- EMOS
Table of Contents
Emos ZT1040 LED Dustproof Luminaire User Manual
Part No.| Input Voltage| Power| Color Temperature (K)| Luminous Flux (lm)|
Beam Angle| Lifespan (hour)| Protection Rate| CRI (Ra)| Dimensions
---|---|---|---|---|---|---|---|---|---
ZT1040| 220–240 V AC| 10–13–16–18 W| 4 000 K–6 500 K| 1 500–2 700 lm| 120°| 50
000 h| IP66| >80| 670 × 85 × 80 mm
ZT1521|
220–240 V AC
|
21–26–31–35 W
| 4 000 K
(neutral white)
| 3 300–5 600 lm|
120°
|
50 000 h
|
IP66
|
80
| 1 220 × 85 × 80 mm
---|---|---|---|---|---|---|---|---|---
ZT1621| 4 600–8 150 lm| 1 520 × 85 × 80 mm
ZT1531|
220–240 V AC
|
29–37–45–51 W
| 6 500 K
(cool white)
| 3 300–5 600 lm|
120°
|
50 000 h
|
IP66
|
80
| 1 220 × 85 × 80 mm
---|---|---|---|---|---|---|---|---|---
ZT1631| 4 600–8 150 lm| 1 520 × 85 × 80 mm
LED Dustproof Luminaire
- LED luminaire is designed for indoor and outdoor use to be mounted on a solid base.
- Ingress Protection IP66 – for outdoor use.
- Housing colour: grey
- Diffuser colour: milky
- Turn off the switch (see Fig. 1).
- Drill ø 6 mm holes according to the below drawing.
Insert ø 6 mm expansion pipe in the wall, and fix the moun ting bracket with an M4 screw (see Fig. 2).
Take off the diffuser with an LED board (see Fig. 3). Loosen the nut of the
cable gland, and put the cable, through the cable gland. Connect the cable on
the terminal block and tighten the cable gland (see Fig. 4). Connect the
terminal block with the LED board (see Fig. 5). Close the diffuser (see Fig.
6).
Fix the gear tray with the housing (see Fig. 7). Turn on the switch (see Fig.
8).
| Type | Power | Fixing Hole Distance |
|---|---|---|
| ZT1040 | 18 W | 400 mm |
| ZT1521 | 35 W | 850 mm |
ZT1531
ZT1621| 51 W| 1 200 mm
ZT1631
POWER SETTING (driver DIP-switch)
WARNING
- Luminaire is suitable entirely for fixed mounting.
- The luminaire can be connected only to the electric distribution network, whose installation and protection comply with the applicable standards.
- Before any manipulation or servicing of the luminaire disconnect the luminaire from AC power. This operation can be carried out only by an authorized person.
- The protection from dangerous contact voltage is ensured by „earthing“.
- In case of any damage to any part of the luminaire, don’t use it.
- LED chips inside the luminaire are not replaceable.
- Don’t change the inner wiring of the luminaire.
- In case of a broken cover don’t use the luminaire and replace the broken cover with a new one immediately.
EMOS spol. s r.o. declares that the LED Dustproof Luminaire complies with the essential requirements and other relevant provisions of the Directive. The device can be freely operated in the EU. The Declaration of Conformity can be found at http://www.emos.eu/download.
This product contains a light source of energy efficiency class D.
Download PDF:Emos ZT1040 LED Dustproof Luminaire User Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>