gemini GTH20BK Ceramic Heater Instruction Manual

: June 15, 2024
: gemini

Table of Contents

SAFETY INSTRUCTION -GENERAL
SAFETY INSTRUCTION – ELECTRICITY AND HEAT
SAFETY INSTRUCTION – DURING OPERATION
INSTALLATION LOCATION OF THE APPLIANCE
FEATURES
DIAGRAM
OPERATION
CONTROL PANEL AND SETTINGS
REMOTE CONTROL
MAINTENANCE
TROUBLESHOOTING
TECHNICAL DATA
Customers Support
Read User Manual Online (PDF format)
Download This Manual (PDF format)

gemini GTH20BK Ceramic Heater

gemini GTH20BK Ceramic Heater

Please read and retain for future reference.

SAFETY INSTRUCTION -GENERAL

Use this appliance solely in accordance with these instructions.
This appliance is for household use only, not for commercial purpose.
Remove all packaging material from the appliance before use.
This appliance shall not be used by children of O to 8-year old.
This appliance can be used by children older than 8-year old and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge, but only if they have been given supervision or instruction concerning use of the appliance in safe way and understand the hazards involved.
Children should be supervised to ensure that they do not play with the appliance.
Cleaning and maintenance must not be done by children.
Have any repairs carried out solely by a qualified electrician. Never try to repair the appliance yourself.
Do not handle the plug or appliance with wet hands.
Do not immerse the main body in water.
Children shall not play with the appliance.
Do not leave the appliance unattended when connected to the mains supply.
Keep hair, loose clothing, fingers and all parts of the body away from openings of the appliance.
Only use the attachments/accessories supplied with the product.

SAFETY INSTRUCTION – ELECTRICITY AND HEAT

Verify that the mains voltage is the same as that indicated on the rating plate on the appliance before use.
Make sure that you always use a grounded wall socket to connect the appliance.
Always remove the plug from the wall socket when the appliance is not in use.
Remove the plug from the wall socket by pulling the plug, not the power cord.
Make sure that the appliance, the power cord and plug do not make contact with water.
Make sure that the appliance, the power cord and plug do not make contact with hot surface, such as a hot hob or naked flame.
Check the appliances’ power cord regularly to make sure it is not damaged.
Do not use the appliance if the power cord is damaged. If the power cord is damaged, it must be replaced by an electrical technician or a person with similar qualification, in order to avoid any hazards.
The appliance needs space to allow heat to escape, thereby preventing the risk of fire. Make sure that the appliance has sufficient space around it, and does not come in contact with flammable material. The appliance, the air vents must not be covered or blocked when use.
Never use the appliance in the vicinity of flammable material.
Certain part of the appliance may get hot, such as air outlet. Do not touch these part to prevent scalding yourself.

SAFETY INSTRUCTION – DURING OPERATION

In use, some parts of the heater are hot. When moving, make sure the heater is switched off.
Do not use the heater in areas such as garages where petrol, paint or other flammable substances are used or stored.
Do not place the heater to furniture, animals, curtains or other inflammables\ objects. Keep combustible materials such as furniture, bedding and any other combustible materials at least 1 metre from the front and sides, and from the rear of the heater.
Do not place the heater on bedding or on thick and long pile carpet where the openings may be blocked.
This product should not be used in the immediate vicinity of water, such as bathtub, washbowls, bathroom swimming pool etc. where the likelihood of immersion or splashing could occur.
A common cause of overheating is deposits of dust and fluff entering the heater. Ensure these deposits are removed regularly by unplugging the heater, allowing it to cool and cleaning as described in the Care, Cleaning and Storage section.
Be sure that no other high current appliances are plugged into the same circuit with your heater as an overload can occur

INSTALLATION LOCATION OF THE APPLIANCE

The appliance should be placed with a minimum distance of 90cm away from flammable objects (e.g. curtains), walls or other structures!
The heater should only be operated at the minimum distance of 50cm from any wall or other objects. Position the air flow in order to optimize the heating of the room. Avoid to place in corners, small volumes and ceilings.

CERAMIC HEATER

FEATURES

Slim design takes minimal space
High Speed Motor with Fan mode and 2 Heat settings
Swing Function
12 hour standby timer.
Remote Control allowing all functions to be changed.

DIAGRAM

Diagram

OPERATION

Your heater may be operated by using either the manual combos located on the front of the fan or by your remote control.

POWER SWITCH ON THE BACK OF THE UNIT
Used to tum the heater ON and OFF. This should be used to tum off the appliance before leaving unattended.

CONTROL PANEL AND SETTINGS

Control Panel And Settings

ON/OFF BUTTON:
Press this button after the product is powered on and the “beep” sound is heard, and run into fan mode. Press this key again to turn off all working states of the Space heater (Note: press this key in the heating mode, the product will continue to work for 30 seconds, the cold air will blow out the heat inside the product, and then turn off all working states).

MODE BUTTON:
Press this button to select the power setting: fan → low heat→ high heat

SWING BUTTON,
Press this button to turn the swing function on and off. When it is operational the horizontal direction of the airflow is slowly moved from side to side and the Swing indicator will be on.

TIMER BUTTON:
Press this button repeatedly to increase the running time in 1-hour intervals. The timer can be set between 1 hour and 12 hours. The di splay will show the duration currently set. When the display is showing the timer duration the h symbol will illuminate next to the timer. To cancel the timer repeatedly press the timer button until 00 Is shown.

TEMP.
After turning on the machine, press this key to adjust the required temperature between1 5-40″C . Each press increases the temperature by 1 “C. After 5 seconds of setting, the ambient temperature will be displayed (automatically adjusted to low heat state when the set temperature is 2″C higher than the ambient temperature, and high heat state when it is higher than 4 “C).

Note: Since the temperature detected by the induction probe is the temperature around the Space heater, the displayed temperature Is different from the actual Indoor temperature, which is only for reference.

The indicator light will automatically turn off after 5 minutes without any operation of the product (the display screen will automatically shut down)

REMOTE CONTROL

Your heater are supplied with a remote control .

REPLACING THE BATTERIES

The remote control is powered by a Lithium Button Cell Battery (CR2025). Should the remote become unresponsive, replace the battery following the instructions below:

Turn over the remote and press tab A to the right.
Slide out the battery tray B
Replace the battery with the same type, ensuring the positive side is facing upwards.

MAINTENANCE

CLEANING AND STORAGE

ATTENTION: Please shut off the unit and unplug from the mains before cleaning or performing any maintenance.

Cleaning the surface
Clean the heater with a duster or a soft wet cloth.
Do not use chemical solvents (such as benzene, alcohol or gasoline) as they may cause irreversible damage. Make sure no water enters the control panel or gaps in the casing.

Do not run the unit until completely dry.
Place the heater in its original box or cover to protect it from dust when not in use. Store it in a cool dry place.