QUANTUM NETWORKS QN-I-210-PLUS Access Point User Guide

Quick Setup Guide
Model: QN-I-210-PLUS

QN-I-210-PLUS Access Point

Copyright Information
Copyright & trademark specifications are subject to change without prior notice. Copyright © 2018 Quantum Networks (SG) Pte. Ltd. All Rights Reserved. Quantum Networks & the logo are trademarks of Quantum Networks (SG) Pte. Ltd. Other brands or products mentioned may be trademarks or registered trademarks of their respective owners. Mentioned contents of this document can’t be used, translated or transmitted in any form or by any means without taking prior written permission from Quantum Networks (SG) Pte. Ltd.
This Quick Setup Guide provides step-by-step instructions on how to set up Quantum Networks Access Point. After completing the steps described in this Guide, you will be able to install the Access Point (AP) on-site and provide wireless network access to users.

Glossary

managed individually. It can be useful in scenarios with few devices or sites with limited Internet access and basic features.
Cloud: In this mode, devices are configured and managed from a central controller hosted in the cloud. It offers many more sets of features as compared to the Standalone mode.
Operation Mode| Bridge: In this mode, the device connects to a network over an ethernet cable and extends the coverage over wireless.
Router: In this mode, the device connects to Internet Service Provider directly using DHCP / Static IP / PPPoE protocols and shares Internet access over a wired or wireless network to users.
Quantum Rudder| Quantum Rudder is a cloud-hosted controller which can be used to configure, manage & monitor devices associated with it. It can be accessed from https://rudder.qntmnet.com 

Icon description

Before you begin

Your Quantum Networks Access Point can work in “Standalone Mode” or can be managed by “Rudder”.

Package contents

• Access Point.
• Mounting kit

Prerequisites

• Internet access.
• Desktop / Laptop / Handheld device.
• 802.3af / 802.3at PoE Switch / PoE Injector.
• 12V, 2A DC power adapter.

Network requisites

The listed ports must be opened or allowed in the network firewall.

• TCP: 80, 443, 2232, 1883.
• UDP: 123, 1812, 1813.
• Allow rudder.qntmnet.com and reports.qntmnet.com in the destination field.

Connect Access Point

• After unpacking Access Point, connect it to an Internet source.
• Plug-in Ethernet cable of Access Point.
• Power on Access Point by using 802.3af / 802.3at PoE Switch / PoE Injector.

Note: Access Point must have Internet access during initial setup for the first time to activate the device, warranty and support.

Step 1 – Create new account on Quantum Rudder

• Browse https://rudder.qntmnet.com.
• Click “Create New Account” to sign up for a new account.
• Follow the steps as guided on the screen for Registration.
• Verify Quantum Rudder account from registered email id. (you will get )
• Once the account gets validated, it turns the page to “Add License Key” (User will get the license key from respective (Partner / Resource) )
• Account on Quantum Rudder (Quantum Networks Cloud Controller) is now ready to use.

Step 2 – Basic setup

• Connect the WAN port of the Access Point to the network with Internet access.

• You should see a new wireless network with SSID QN_XX:XX (where XX:XX are the last four digits of Access Point MAC Address).

• Connect to QN_XX:XX SSID and browse Access Point’s default IP “169.254.1.1”.Let’s start the configuration.
  On the configuration start page, it will display,

• Device model number

• Serial number

• MAC address

• Current firmware

Note:

• Click button to get the option to “change the firmware” if required.
• Click Change Firmware to update firmware if required. Select the firmware file from the respective location and update it.

Step 3 – Setting up device IP address

Click “Configure” and set the device IP address by selecting the required options.

• Connectivity Mode – Select the connectivity mode.
• Protocol – DHCP, Static or PPPoE
• Interface – Select interface
• VLAN Assignment- Enable parameter. Enter VLAN ID and click “Fetch IP Address” to get the respective IP in case of VLAN setup is required.

Click “Proceed” to apply configuration and turn to the next page.

Step 4 – Set the management mode

Management Mode
Quantum Networks Access Point can be configured in two modes:
Rudder (on cloud / on-premise)
Centralized management of Access Points using Quantum Rudder
Standalone
Independent management of each Access Point

Step 5 – Access Point quick setup in Rudder Mode

• Select “Management Mode” as “Rudder”, enter Quantum Rudder login credentials and click “Proceed”.
• It will verify the credentials, and turn to a next page.
• Upgrade QNOS version by either downloading from the cloud or by selecting manually from respective location and upgrade or click “Skip Upgrade” to move further.
• The user will turn to a page where the user has to select the site and AP group.
• Select Rudder site and AP Group where Access Point’s needs to be added and click “Proceed”.
  o If the selected site is already having another Access Point, it will automatically configure AP in a bridge mode and will turn the user on the summary page after clicking “Proceed”. (Figure 8)
  o If this is the first Access Point for the selected site – the user will turn on the page, where the user can select Access Point Operation mode as Bridge or Router. (Figure 9)

Bridge

• Select option Bridge and click “Proceed”.
• Configure WLAN (SSID) parameters and click “Proceed”.

Router

• Select option Router and click “Proceed”.
• Configure WLAN (SSID) and Local subnet parameters and click “Proceed”.

Access Point
IP Address| LAN Subnet mask

Note: If you do not want to create WLAN (SSID)/LAN now, click the Skip option. It will turn to Configuration Summary.

• Review the Configuration Summary. Click “Reconfigure” if any changes are required or click “Proceed” to complete the configuration.

Step 6 – Access Point quick setup in standalone mode

• Select “Management Mode” as “Standalone” if each Access Point is to be configured and managed individually. Define username and password for the device and click “Proceed”.
• User can select Access Point Operation mode as Bridge or Router.

Bridge

• Select option Bridge and click “Proceed”.
• Configure WLAN (SSID) parameters and click “Proceed”.
  Parameter| Value
  ---|---
  Country| Select country for radio management.
  Timezone| Select timezone for Rudder management.
  WLAN Name| Define a name for the network.
  SSID| Define visible wireless network name.
  Passphrase| Configure a passphrase for SSID.
• Review the Configuration Summary. Click “Reconfigure” if any changes are required or click “Proceed” to complete the configuration.

Router

• Select option Router and click “Proceed”.
• Configure WLAN (SSID) and Local subnet parameters and click “Proceed”.

Access Point.
Subnet Mask| LAN subnet mask.

• Review the Configuration Summary. Click “Reconfigure” if any changes are required or click “Proceed” to complete the configuration.

Reset Access Point to factory defaults

• Power on the Access Point
• Push the reset button on the back panel and hold it for 10 seconds.
• Access Point would restart with factory defaults

Access Point default login detail

With standalone mode:
User Name: Created while doing “Quick Setup”
Password: Created while doing “Quick Setup”
With Rudder mode:
User Name: Auto Generated, administrator can change from site settings.
Password: Auto Generated, administrator can change from site settings.
If you encounter problems while installing or using this product, please browse www.qntmnet.com for:

• Direct contact with the support center.

• o Contact: 18001231163
  o Email: support@qntmnet.com

• For the latest software, user documentation and product updates browse: qntmnet.com/resource-library

www.qntmnet.com

References

• Quantum Network
• Quantum Network
• Quantum Network

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>