Godox TR-TX Wireless Timer Remote Control Instruction Manual

Godox TR-TX Wireless Timer Remote Control

Foreword

Thank you for purchasing’ TR is a high-performance wireless timer remote control for cameras, it can control the camera shutter with flash trigger XPROII (optional). TR features single shooting, continuous shooting, BULB shooting, delay shooting and timer schedule shooting, quite suitable for planet motion shooting, sunrise and sunset shooting, flowers blooming shooting etc.

Warning

Do not disassemble. Should repairs become necessary, this product must be sent to an authorized maintenance center.
Always keep this product dry. Do not use in rain or in damp conditions.
Keep out of reach of children. Do not use the flash unit in the presence of flammable gas. In certain circumstance, please pay attention to the relevant warnings.
Do not leave or store the product if the ambient temperature reads over 50°C.
Observe precautions when handling batteries :

• Use only batteries listed in this manual. Do not use old and new batteries or batteries of different types at the same time.
• Read and follow all warnings and instructions provided by the manufacturer.
• Batteries cannot be short-circuited or disassembled.
• Do not put batteries into a fire or apply direct heat to them.
• Do not attempt to insert batteries upside down or backwards.
• Batteries are prone to leakage when fully discharged. To avoid damage to the product, be sure to remove batteries when the product is not used for a long time or when batteries run out of charge.
• Should liquid from the batteries come into contact with skin or clothing, rinse immediately with fresh water.

Name of Parts

Transmitter TR-TX

1. Indicator
2. Display Screen
3. Timer Start/Stop Button
4. Alert/Lock Button
5. Left Button
6. Down Button
7. Up Button
8. Right Button
9. SET Button
10. Shutter Release Button
11. Power Switch Button
12. Channel Button
13. Battery Cover
14. Wireless Shutter Jack
    

Display Screen of Transmitter

1. Channel Icon
2. Timer Shooting Numbers Icon
3. Locking Icon
4. Alert Icon
5. Battery Level Icon
6. Time Display Zone
7. DELAY Timer Schedule Delay Icon
8. LONG Timer Schedule Exposure Time Icon
9. INTVL1 Timer Shooting Interval Time Icon
10. INTVL2 Repeat Timer Schedule Interval Time Icon
11. INTVL1 N Timer Shooting Numbers
12. INTVL2 N Repeat Timer Schedule Times

Receiver TR-RX

1. Display Screen
2. Channel Setting/- Button
3. Channel Setting/- Button 6. 1/4″ Screw Hole Power Switch/+ Button
4. Coldshoe
5. Battery Cover
6. 1/4″ Screw Hole
7. Wireless Shutter Jack
   

Display Screen of Receiver

1. Channel Icon
2. Battery Level Icon

What’s Inside

• Cl Shutter Cable

• C3 Shutter Cable

• N1 Shutter Cable

• N3 Shutter Cable

• Pl Shutter Cable

• OPl2 Shutter Cable

• S1 Shutter Cable

• S2 Shutter Cable

• Instruction Manual

• Transmitter

• Receiver

Manualx1
TR-S1| Transmitter x1 Receiver x1 S1 Shutter Cable x17 Instruction Manualx1
TR-S2| Transmitter x1 Receiver x1 S2 Shutter Cable x1Instruction Manualx1

Compatible Cameras

TR-Cl

Compatible Models

Canon:| 90D,80D, 77D, 70D,60D,800D, 760D, 750D, 700D, 650D,600D,550D ,500D-450D, 400D,350D,300D,200D, 700D, l 500D, l 300D, 1200D, 1700D, 7000D,Gl O,G1 7-Gl 2, G1 5,Gl 6,GlX,SX70,SX60,SX50, EOS M6,M6II,M5
PENTAX:| K5,K7, Kl 0, K20, Kl 00, K200, Kl, K3,K30, Kl OD, K20D,K60
SAMSUNG:| GX-1 L, GX-1 S, GX-10,GX-20,NXlOO,NXl 1 ,NX1O, NX5
Contax:| 645, N1 ,NX, N diglita1H series

TR-C3

Compatible Models

Canon:| 10s Mark IV, 10s Mark Ill_ 5D Mark III,5D Mark IL l Os Mark II, 50D- 40D,30D,20D, 70D, 7D-7D11, 60,5D,5D2,5D3, 1DX, 10s, 10,EOS-lV

TR-N1

Compatible Models

Nikon:| D850, DSOOE, D800, D700, D500, D300s, D300, D200, D5, D4, D3S, D3X, D3, D2Xs, D2x.Dl X, D2HS, 02H, 07 H, Dl, Fl 00, N90S, F90X, F5, F6, F90
 FUJIFILM:| S5 Pro, S3 Pro

TR-N3

Compatible Models

Nikon: D750, D610, D600, D7500, D7200, D7100, D70DC, D5600, D5500, D5300, D5200, D51 DC, D5000, D3300, D3200, D3100, D90

TR-S1

Compatible Models

SONY:a900, a 850, a 700, a 580, a 560, a550, a500, a450, a 400, a 350, a 300, a 200, a 7 00, a 99, a 9911, a77, a77II,a65, a57 ,a55, a35,a33

TR-S2

Compatible Models

SONY :a7, a7m2, a7m3, a 7S, a7SI I, a7R, a 7RII, a9, a 911, a58, a 6600, a 6400, a 6500, a6300, a6000, a51 00, a 5000, a 3000, NEX-3NL, HX50, HX60, HX300, HX400, R1 RM2, RX1 OM2, RX1 OM3, RX1 OM4, RX1 OCM2, RX1 OOM3, RX1 OOM4, RX1 OCM5, RX1 OOM6, RX1 OOM7

TR-Pl

Compatible Models

Panasonic:GH5II,GH5S, GH5,G90,G91, G95,G9,S5,Sl H, DC-S1 R,DC-S1 ,FZ1 00011, BGH1, DMC-GH4,GH3,GH2,GH1 ,GX8,GX7, GX1, DMC-G7, G6,G5,G3,G2,G85,Gl 0, G1, G1l, DMC-FZ2500, FZ1 000, FZ300, FZ200, FZ1 50

TR-OP12

Compatible Models

Olympus:E-620, E-600, E-520, E-510, E-450, E-420, E-41 0, E-30, E-M5, E-P3, E-P2, E-Pl, SP-570UZ, SP-560UZ, SP-560UZ, SP-51 OUZ, A900, A850, A 700, A580, A560

Battery Installation

When the< o > blinks on the display, please replace the battery with two AA batteries.
Slide and open the battery cover on the back, install two AA 7 .5V alkaline batteries as shown in the pictures below.

Note: Please pay attention to the positive and negative poles of the battery when installing, incorrect installation not only disables the device, but also may cause personal injury.

Power Switch
Long press the power switch buttons of transmitter and receiver for 7 s to turn on or off them.
Backlight
Short press any button of the transmitter and receiver to turn on backlight for 6s. The backlight will continue to be turned on in further operation, and will be turned off after idle use of 6s.
Locking Function
Transmitter: Long press the alert/lock button until the locking icon shows on the display, then the display screen is locked and operations of other buttons are unavailable. Long press the alert/lock button again until the locking icon disappear, then display screen is unlocked and operations resumed.
Alert
Transmitter: Short press the alert/lock button to turn on or off the alert.

Wireless Control of Cameras

Connect the receiver and camera

First make sure both the camera and receiver are powered off. Attach the camera to a tripod (sold separately) and insert the cold shoe of receiver into the top of the camera.
Insert the input plug of the shutter cable into the output port of the receiver, and the shutter plug into the external shutter socket of the camera. After which, power on the receiver and camera.

Connect the transmitter and receiver

2. 1 Long press the power switch button of transmitter for 7 s to power on, short press the channel button and the channel icon blinks, then short press the up button or down button to select channel (assume the selected channel is 7 ). then short press the channel button to exit or exit automatically until idle use of 5s.

2.2 Set channel
A {Adjust manually): Long press the power switch button of receiver for ls to power on, short press the channel button for ls and the channel icon blinks, then short press the – button or+ button to select channel (assume the selected channel of transmitter is l, then the channel of receiver should be set as 7), then long press the channel button to exit or exit automatically until idle use of 5s.

B {Adjust automatically): Long press the channel button of transmitter for 3s and the indicator flashes red, long press the channel button of receiver for 3s and the channel icon blinks. When the indicator of receiver turns to green, the channel of it will be the same as the transmitter’s, after which short press any button of transmitter to exit.

2.3 After the above settings, the camera can be controlled remotely.

Note : The transmitter and the receiver should be set to the same channel for effective control.

Wired Control of Cameras

1. First make sure both the camera and receiver are powered off. Attach the camera to a tripod (sold separately), insert the input plug of the shutter cable into the output port of the transmitter, and the shutter plug into the external shutter socket of the camera. After which, power on the transmitter and camera.

Single Shooting

1. Set the camera to single shooting mode.
2. Half-press shutter release button, the transmitter will send focus signal. The indicators on the transmitter and receiver will light on green, and the camera is in focusing status.
3. Full-press shutter release button, the transmitter will send shooting signal. The indicators on the transmitter and receiver will light on red, and the camera is shooting.

Continuous Shooting

1. Set the camera to continuous shooting mode.
2. Half-press shutter release button, the transmitter will send focus signal. The indicators on the transmitter and receiver will light on green, and the camera is in focusing status.
3. Full-press shutter release button, the indicators on the transmitter and receiver will light on red, the transmitter will send continuous shooting signal, and the camera is shooting.

BULB Shooting

1. Set the camera to bulb shooting mode.
2. Half-press shutter release button, the transmitter will send focus signal. The indicators on the transmitter and receiver will light on green, and the camera is in focusing status.
3. Full-press and hold shutter release button until the transmitter flashes red and starts time keeping while the receiver lights on red, then release the button, and the transmitter will send BULB signal, the Receiver outputs shooting signal continuously, then the camera starts to continuous exposure shooting. Short press shutter release button again, the camera stops shooting, the indicators on the transmitter and receiver light off.

Delay Shooting

1. Set the camera to single shooting mode.

2. Set the delay time of transmitter: Short press the left button or right button to switch to in power on status. Short press the SET button to enter delay time setting interface, the time display zone blinks, short press the left button or right button to switch hour/minute/second settings. Short press the up button or down button can set values of hour/minute/second with the display zone blinking, then short press the SET button to exit
   or exit automatically until idle use of 5s.
   Adjustable values of “hour”: 00-99
   Adjustable values of “minute”: 00-59
   Adjustable values of “second”: 00-59

3. Set the shooting numbers of transmitter Short press the left button or right button to switch to <IN1VL 1 N>, short press the SET button to enter shooting numbers setting interface. Short press the up button or down button can set numbers of shooting with the display zone blinking, then short press the SET button to exit or exit automatically until idle use of 5s.
   Adjustable numbers of shooting: 001-999/ — (infinite)

4. Half-press shutter release button, the transmitter will send focus signal. The indicators on the transmitter and receiver will light on green, and the camera is in focusing status.

5.  Short press the timer on/off button, the transmitter sends shooting information to the receiver, then starts time-lapse countdown.

6. After the countdown, the receiver will control the camera shooting according to the original shooting signal, the indicator will light up red once for each shot.
   Note: Short press the timer on/off button when the delay shooting is not completed will terminate it.

Timer Schedule Shooting

1. Set the camera to single shooting mode.

2.  Set the delay time of transmitter: Short press the left button or right button to switch to in power on status. Short press the SET button to enter delay time setting interface, the time display zone blinks, short press the left button or right button to switch hour/minute/second settings. Short press the up button or down button can set values of hour/minute/second with the display zone blinking, then short press the SET button to exit or exit automatically until idle use of 5s.
   Adjustable values of “hour”: 00-99
   Adjustable values of “minute”: 00-59
   Adjustable values of “second”: 00-59

3. Set the exposure time of transmitter: Short press the left button or right button to switch to< LONG>. Short press the SET button to enter exposure time setting interface, the time display zone blinks, short press the left button or right button to switch hour/minute/second settings. Short press the up button or down button can set values of hour/minute/second with the display zone blinking, then short press the SET button to exit or exit automatically until idle use of 5s.
   Adjustable values of “hour”: 00-99
   Adjustable values of “minute1′: 00-59
   Adjustable values of “second”: 00-59

4. Set the timer schedule shooting interval time of transmitter: Short press the left button or right button to switch to< INTVL l >. Short press the SET button to enter timer schedule shooting interval time setting interface, the time display zone blinks, short press the left button or right button to switch hour/minute/second settings. Short press the up button or down button can set values of hour/minute/second with the display zone blinking, then short press the SET button to exit or exit automatically until idle use of 5s.
   Adjustable values of “hour”: 00-99
   Adjustable values of “minute”: 00-59
   Adjustable values of “second”: 00-59

5. Set the shooting numbers of transmitter. Short press the left button or right button to switch to <INTVL 1 N>, short press the SET button to enter shooting numbers setting interface. Short press the up button or down button can set numbers of shooting with the display zone blinking, then short press the SET button to exit or exit automatically until idle use of 5s.

6. Set the repeat timer schedule interval time of transmitter Short press the left button or right button to switch to< INTVL2>. Short press the SET button to enter repeat timer schedule interval time setting interface, the time display zone blinks, short press the left button or right button to switch hour/minute/second settings. Short press the up button or down button can set values of hour/minute/second with the display zone blinking, then short press the SET button to exit or exit automatically until idle use of 5s.
   Adjustable values of “hour”: 00-99
   Adjustable values of “minute”: 00-59
   Adjustable values of “second”: 00-59

7. Set the repeat timer schedule times of transmitter Short press the left button or right button to switch to , short press the SET button to enter repeat timer schedule times setting interface. Short press the up button or down button can set numbers of shooting with the display zone blinking, then short press the SET button to exit or exit automatically until idle use of 5s. Adjustable times of repeat timer schedule: 007-999/— (infinite)

8. Half-press shutter release button, the transmitter will send focus signal. The indicators on the transmitter and receiver will light on green, and the camera is in focusing status.

9. Short press the timer on/off button, the transmitter sends shooting information to the receiver, then starts time-lapse countdown.

10. After the countdown, the receiver will control the camera shooting according to the original shooting signal, the indicator will light up red once for each shot.
    Note: The exposure time set by the remote control should be consistent with the camera. If the exposure time is less than 1 second, the exposure time of the remote control must be set to 00:00:00. Short press the timer on/off button when the delay shooting is not completed will terminate it

Timer Schedule Shooting Illustration

Timer schedule shooting A: delay time [DELAY]= 3s, exposure time [LONG]= 1 s, timer schedule shooting interval time [INTVL 1] = 3s, shooting numbers [INTVL 1 N] =2, repeat timer schedule interval time [INTVL2] = 4s, repeat timer schedule times [INTVL2 N]=2.

Timer schedule shooting B: delay time [DELAY] = 4s, exposure time [LONG]= 2s, timer schedule shooting interval time [INTVL 1] = 4s, shooting numbers [INTVL 1 NI= 2, no need to repeat timer schedule, [INTVL2] = ls, no need to repeat timer schedule, [INTVL2 N] =1.

Technical Data

Repeat Timer Schedule

Interval Time

| Os to 99h59min59s (with an increment of 1 s)/
Repeat Timer

Schedule Times

| 7 ~999 —(infinite)/
Channel| 32
Controlling Distance| | ,,,,oom
Working Environment

Temperature

| -20°C~+50°C
Dimension| 99mm52mm27mm| 75MM4435MM
Net Weight (including

AA batteries)

| Net Weight (including

AA batteries)

| 84g| 84g

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and.
2. this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
   • Reorient or relocate the receiving antenna.
   • Increase the separation between the equipment and receiver
   • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
   • Consult the dealer or an experienced radio/TV technician for help.
     The device has been evaluated to meet general RF exposure requirement.
     The device can be used in portable exposure condition without restriction.

Warning
Operating frequency:2412.99MHz – 2464.49MHz Maximum EIRP Power 3.957dBm
Declaration of Conformity
GODOX Photo Equipment Co.,Ltd. hereby declares that this equipment are in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this product is allowed to be used in all EU member states. For more information of Doc, Please click this web link: https://www.godox.com/eu- declaration-of-conformity/

The device complies with RF specifications when the device used at 0mm from your body.

Warranty Period

The warranty period of products and accessories is implemented according to the relevant Product Maintenance Information. The warranty period is calculated from the day (purchase date) when the product is bought for the first time, And the purchase date is considered as the date registered on the warranty card when buying the product.

How to Get the Maintenance Service

If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the Godox after-sale service call and we will offer you service. When applying for maintenance service, you should provide valid warranty card. If you cannot provide valid warranty card, we may offer you maintenance service once confirmed that the product or accessory is involved in the maintenance scope, but that shall not be considered as our obligation.
Inapplicable Cases

The guarantee and service offered by this document are not applicable in the following cases: ① . The product or accessory has expired its warranty period;② . Breakage or damage caused by inappropriate usage, maintenance or preservation, such as improper packing, improper usage, improper plugging in/out external equipment, falling off or squeezing by external force, contacting or exposing to the improper temperature, solvent, acid, base, flooding and damp environments, etc;③. Breakage or damage caused by non- authorized institution or staff in the process of installation, maintenance, alternation, addition and detachment;④ . The original identifying information of product or accessory is modified, alternated, or removed;⑤ . No valid warranty card;⑥ . Breakage or damage caused by using illegally authorized, nonstandard or non-public released software; ⑦ . Breakage or damage caused by force majeure or accident;⑧ . Breakage or damage that could not be attributed to the product itself. Once met these situations above, you should seek solutions from the related responsible parties and Godox assumes no responsibility. The damage caused by parts, accessories and software that beyond the warranty period or scope is not included in our maintenance scope. The normal discoloration, abrasion and consumption are not the breakage within the maintenance scope.

Maintenance and Service Support Information

The warranty period and service types of products are implemented according to the following Product Maintenance Information:

Product Type| Name| Maintenance Period(month)| Warranty Service Type
---|---|---|---
Parts| Circuit Board| 12| Customer sends the product to designated site
Battery| | Customer sends the product to designated site
Electrical parts e.g. battery charger, etc.| 12| Customer sends the product to designated site
Other Items| Flash tube, modeling lamp, lamp body, lamp cover, locking device, package, etc.| NO| Without warranty

Wechat Official Account

GODOX Photo Equipment Co., Ltd.
Add.: Building 2, Yaochuan Industrial Zone, Tangwei Community, Fuhai Street, Bao’ an District, Shenzhen
518103, China Tel: +86-755-29609320(8062) Fax: +86-755-25723423 E-mail: godox@godox.com
www.godox.com
Made in China I 705-TRCl 00-01

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>