fingers Satin-1850 Big Picture LED Monitors User Guide

18.5
Satin-1850
46.99cm
Quick Start Guide

Important – Warnings & Safety Instructions

1. Do not place the product near heat sources such as fire, radiators, stoves, light candles and other apparatus that produce heat.
2. Use only those accessories supplied by FINGERS.
3. Refer all servicing to qualified personnel. Servicing is required when the monitor has been damaged in any way. Any evidence of any attempt to open and/or alter the device, including any scratch, peeling, puncturing, or removal of any of the labels, will void the Limited Warranty.

In the box

On-board Controls

Installations Steps

1. Take out the stand and place it on a flat table as shown in below image.

2. Take out the monitor body, place it on a flat table & keep the screen side downward.

3. Install the base with a stand of monitor body tightly. Note that there is a rachet on the base to fix it as per notch location as shown in below image.

4. The setup is done and the required cables can be connected.

Steps to remove the Stand

1. Place the monitor upside-down on a flat table.

2. Please hold on to the monitor body, press the lock, pull the rachet up on the base and draw out the base at the same time, as shown in the image below.
   

Viewing Adjustment

To get the best viewing, we suggest facing the screen of the monitor and adjusting it to your perspective according to your personal preference. Please hold the monitor stand support during angle adjustment to avoid directly touching the  display. The display angle can be adjusted within -5° to 20° range.

Note:

1. Make sure there are no objects surrounding the monitor before adjusting the monitor angle, to prevent the bump of monitor screen with any objects during the adjustment.
2. Make sure the monitor is on a flat table and not on unbalanced surface, during the adjustment.
3. We recommend holding the base stand while adjusting the angle and gently adjust the angle by holding the top of the monitor with another hand.

Care and Maintenance

1. Unplug the monitor power plug before cleaning it.
2. Use the cleaning kit & spray the cleaning liquid on the cleaning cloth, and then gently wipe on the display surface.
3. Use soft cloth to clean the surface.
4. Plug in the monitor power plug after the cleaning process is complete and then switch on the monitor’s power.
5. Do not use any chemicals, solvents, or cleaning solutions containing alcohol, ammonia, or abrasives.
6. Do not allow any liquid to enter any of the openings.

Tech Specs

Maximum resolution Colour
Refresh rate Response time
Dynamic Contrast Ratio Static Contrast Ratio Brightness
Aspect ratio Viewing angle Pixel pitch Lighting type| 469.9 mm (18.5″) Colour TN LED
409.8 (H) x 230.4(V)
469.9 mm (18.5″)
1366 x 768 pixels
16.7 million
75 Hz
5 ms (Typical, TR.+ TF.) 500000:1
600:1
200-250 cd/m2
16:9
H:130°/ V:110° (CR>10) 0.300 (H) x 0.300 (V) mm LED
Connectivity| Analog Input Digital Input| VGA x 1 HDMI x 1
Power| Power Consumption Stand-by Power
Power Supply| s 21 Watts
s 1 Watts
AC 185 — 255 V, 1.0 A
Environmental| Temperature (Operating) Temperature (Non-Operating) Humidity (Operating) Humidity (Non-Operating)| 0°C to 50°C
-10 to +60°C
20% to 60% RH 5% to 90% RH
Features| Tilt angle
Low Blue Mode
Flicker Free
Anti-Glare
Kensington Lock Support| -5 to +15°C
Yes
Yes (DC dimming)
Yes Yes
Dimensions and weight| Wall Mountable
Monitor (W x H x D) Net Weight| 75 x 75 mm
441 x 193 x 345 mm 1.94 kg

fingers.co.in I Ver.: 1.0.0
Images shown may vary from actual product.
Specifications, features and appearance are subject to change without notice.
All logos, brands, trademarks and product names are properties of their respective owners.
Product warranty  is governed by warranty terms mentioned on www.fingers.co.in
This product falls under e-waste (Management & Handling) Rules, 2011. For proper disposal method, visit our website www.fingers.co.in

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>