SONOFF MINI R4 Extreme Wi-Fi Smart Switch User Guide
- June 15, 2024
- SonOFF
Table of Contents
SONOFF MINI R4 Extreme Wi-Fi Smart Switch
Power off
Please install and maintain the device by a professional electrician.
To avoid electric shock hazard, do not operate any connection or contact the
terminal connector while the device is powered on!
Wiring instruction
- No matter S1 and S2 are connected or left idle to the external switch, this device can be controlled by automation or the App.
- It is prohibited to connect S1 and S2 terminals to the neutral or ground wire, in order to avoid damaging the equipment and causing danger.
- Make sure all wires are connected correctly.
Download the eWeLink App
Power on
After powering on, the device will enter the Pairing Mode during the first use. The LED indicator changes in a cycle of two short and one long flash.
Add device
Tap “+” and select “Add Device”, then operate following the prompt on the App.
It’s required to turn on the Bluetooth on your Phone when adding a device.
Add eWeLink-Remote Sub-devices
Enter the Device Settings page on the eWelink App, select “eWeLink-Remote sub- devices” and tap “Add”, then trigger the sub-device to add it successfully.
Equipment Installation
https://sonoff.tech/usermanuals
Scan the OR code or visit the website to learn about the detailed user manual
and help.
FCC compliance statement
-
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: -
This device may not cause harmful interference, and
-
This device must accept any interference received, including interference that may cause undesired operation.
-
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with minimum distance of 20 cm
between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
SAR Warning
Under normal use of condition, this equipment should be kept a separation
distance of at least 20 cm between the antenna and the body of the user.
EU Declaration of Conformity
Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio
equipment type MINIR4 is in compliance with Directive 2014/53/EU. The full
text of the EU declaration of conformity is available at the following
internet address: https://sonoff.tech/compliance/
For CE Frequency
Operation frequency Range
BLE: 2402-2480MHz
Wi-Fi: 2412-2472MHz
RF Output Power
BLE≤10dBm
Wi-Fi 2.4G≤20dBm
WEEE Disposal and Recycling Information
All products bearing this symbol are waste electrical and electronic equipment
(WEEE as in directive 2012/19/EU) which should not be mixed with unsorted
household waste.
Instead, you should protect human health and the environment by handing over
your waste equipment to a designated collection point for the recycling of
waste electrical and electronic equipment, appointed by the government or
local authorities. Correct disposal and recycling will help prevent potential
negative consequences to the environment and human health. Please contact the
installer or local authorities for more information about the location as well
as terms and conditions of such collection points.
To ensure the safety of your electrical installation, it’s essential either a Miniature Circuit Breaker (MCB) or a Residual Current Operated Circuit Breaker (RCBO) with an electrical rating of 10A has been installed before the MINIR4.
Shenzhen Sonoff Technologies Co., Ltd.
3F & 6F, Bldg A, No. 663, Bulong Rd, Shenzhen, Guangdong, China
ZIP code: 518000
Website: sonoff.tech
Service email: support@itead.co
MADE IN CHINA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>