SONOFF NS Panel Smart Scene Wall Switch User Guide
- June 15, 2024
- SonOFF
Table of Contents
SONOFF NS Panel Smart Scene Wall Switch
Power off
Please install and maintain the device by a professional electrician. To avoid electric shock hazard, do not operate any connection or contact the terminal connector while the device is powered on!
Wiring instruction
Make sure the neutral wire and live wire connection is correct.
Equipment Installation
Download the eWeLink App
Power on
After powering on, the device will enter the Bluetooth Pairing Mode during the
first use.
The screen status is shown in the above image.
Add Device
Tap “+” and select “Add Device”, then operate following the prompt on the App.
It’s required to turn on the Bluetooth on your Phone when adding a device.
Operation Guide
Dropdown
Settings of the screen brightness and sleep time.
Swipe right
After adding temperature controller function in the APP, you can set the added
temperature controller on the device.
Swipe left
After adding widgets in the APP, you can control the added widgets on the
device.
https://sonoff.tech/usermanuals
Scan the QR code or visit the website to learn about the detailed user manual
and help.
FCC compliance statement
- This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with minimum distance of 20 cm
between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
For CE Frequency
EU Operating Frequency Range
Wi-Fi:802.11 b/g/n20 2412-2472 MHz
BLE: 2402-2480 MHz
EU Output Power
Wi-Fi 2.4G≤20dBm
BLE≤10dBm
EU Declaration of Conformity
Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio
equipment type NSPanel-US, NSPanel-USW is in compliance with Directive
2014/53/EU.The full text of the EU declaration of conformity is available at
the following internet address: https://sonoff.tech/compliance/
ISED Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is
subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003(B).
This device complies with RSS-247 of Industry Canada.
Operation is subject to the condition that this device does not cause harmful
interference.
ISED Radiation Exposure Statement
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with minimum distance of 20 cm
between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
SAR Warning
Under normal use of condition, this equipment should be kept a separation
distance of at least 20 cm between the antenna and the body of the user.
WEEE Disposal and Recycling Information
All products bearing this symbol are waste electrical and electronic equipment
(WEEE as in directive 2012/19/EU) which should not be mixed with unsorted
household waste. Instead, you should protect human health and the environment
by handing over your waste equipment to a designated collection point for the
recycling of waste electrical and electronic equipment, appointed by the
government or local authorities.
Correct disposal and recycling will help prevent potential negative
consequences to the environment and human health. Please contact the installer
or local authorities for more information about the location as well as terms
and conditions of such collection points.
To ensure the safety of your electrical installation, it’s essential either a Miniature Circuit Breaker (MCB) or a Residual Current Operated Circuit Breaker (RCBO) with an electrical rating of 4A has been installed before the NSPanel- US, NSPanel-USW.
Shenzhen Sonoff Technologies Co., Ltd.
3F & 6F, Bldg A, No. 663, Bulong Rd, Shenzhen, Guangdong, China
ZIP code: 518000
Website: sonoff.tech
Service email: support@itead.cc
MADE IN CHINA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>