Temas Teknoloji LS17RM Motorized Retractable Monitor lift with Microphone User Manual

Temas Teknoloji LS17RM Motorized Retractable Monitor lift with Microphone

Specifications:

• Structural and functional characteristics: AX-17MG motorized monitor lift is using the synchronous belt
• Cut out size (for Bosch): [insert cut out size here]
• Product size (for Bosch): [insert product size here]
• Technical parameters of lifts:
  • Voltage: AC 220V 50HZ
  • Power: [insert power details here]
  • [insert other technical parameters here]

Product Usage Instructions

Safety Instructions:

Before using the device, please read and follow the safety instructions below:

1. If any abnormal situation is found, immediately cut off the power, pull off the plug, and contact your supplier. Do not use the device in the following situations:
   • If you notice a peculiar smell or fog coming from inside the unit.
   • If there is water or metal parts entering the unit.
   • If the lift unit box is broken.
   • If the wire is broken inside.
2. As the device operates under high pressure, do not open the unit box randomly to avoid fire or electric shock.
3. Do not put any conducting liquid on top of the device to avoid electric shock or fire.
4. The device is of Type I; make sure the power is connected to the ground.
5. The device is suitable for AC 220V 50Hz power supply.
6. Avoid placing the machine in direct sunlight to prevent high temperature, circuit board short circuit, fire, or electric shock.
7. When the product is lifted, do not place heavy objects on the top panel to prevent excessive lifting load and extend the service life of the equipment.
8. To avoid damage, install the fastening screws of the device, pull off the power plug and other cables before moving it, and remove the fastening screws before reconnecting the power.

Operation Instructions:

Follow the steps below to operate the device:

2.1 Packing List:

2.2 Interface on the Top Panel (from left to right):

1. Bosch control for monitor movement
2. Microphone switch control

2.3 Interface on the Bottom Case (from left to right):

• AC 220V input
• ANT Remote control (optional)
• SparePC SW power on
• SA SW signal switch
• RS485 in1
• RS-485 +2
• RS-485 -5
• GND RS485 out for cluster control
• USB input (up: USB data, down: USB touch)
• VGA in (optional)
• HDMI in

2.4 Introduction to Manipulation:

• Display button
• Menu Auto
• Led: Indicated light (NO SIGNAL: red, WITH SIGNAL: green)
• Display power on/off
• Variable Button (-)
• Variable Button (+)
• AUTO: Automatic adjustment button with return function
• MENU

Frequently Asked Questions (FAQ):

Q: What should I do if I notice a peculiar smell or fog coming from inside the unit?

A: Immediately cut off the power, pull off the plug, and contact your supplier.

Q: Can I place heavy objects on the top panel when the product is lifted?

A: No, heavy objects should not be placed on the top panel as it may cause excessive lifting load and affect the service life of the equipment.

Q: How should I move the equipment without causing damage?

A: Before moving the equipment, install the fastening screws of the device, pull off the power plug and other cables. Remove the fastening screws before reconnecting the power.

Read the instructions carefully before using the device

warning

In order to make sure the device is working properly, please follow below instructions:

• a. If found any abnormal situation, please cut off the power, pull off the plug and contact your supplier. To avoid any fire accident, DON’T use device in following situations:
  If you found peculiar smell or fog comes from inside of unit.

  • If have water or metal parts going to the unit.
  • If the lift unit box is broken.
  • If the wire is broken inside.

• b. As the device is high pressure inside, please DON’T open the unit box at random to avoid fire or electric shock,.

• c. DON’T put any conducting liquid on top of the device, to avoid electric shock or fire.

• d. The device is I type; the power should be connected to ground.

• e. The device is suitable for AC 220V 50Hz.

• f. DO NOT place the machine in the direct sunlight area, avoid causing high temperature, circuit board short circuit, fire or electric shock.

• g. When the product is lifted, no heavy objects shall be placed on the top panel, which may easily cause excessive lifting load and affect the service life of the equipment.

• h. To avoid damage to the equipment, please install the fastening screws of the device and pull off power plug and other cables before moving it, and remove the fastening screws before connecting the power again.

Operation instructions

packing list

Interface on the top panel（from left to right, for Bosch）

Interface on the bottom case（from left to right）

• AC 220V input
• ANT Remote control ( optional )
• Spare：PC SW power on; SA SW signal switch
• RS485 in（1：RS-485 +，2：RS-485 -，5：GND）
• RS485 out（use for cluster control ）
• USB input，up: USB data， down: USB touch
• VGA in（optional）
• HDMI in

Introduction to Manipulation

Display button

Characteristics and main parameters

Structural and functional characteristics
AX-17MG motorized monitor lift is using the synchronous belt pulley with a straight line for rising and falling, the tilt driver will as a individual part and fixed 16°. Stable structure and low noise, using the aluminum frame match with the toughened glass, more elegant. The product uses the desktop embedded design, could hide in the table perfectly, two motors control the movement of screen and microphone, also auto-calibration movement of microphone protect the gooseneck from damage by performance error.

Cut out size (for Bosch)

product size (for Bosch)

Technical parameters of lifts

consumption

| <45W
3| Single running

time

| 13S
4| Tilting| 15° fixed
---|---|---
5| Working

temptation

| 0—50℃

Technical parameters of display screen

2. Installation instructions

• Please remove 4 pcs safety screws & remove the foam inside the case before charging (the screws are in the, back, right & left side of cover plate)
• Put the lift into to table cutting hole, and flushing the panel with the table.
• Connect the video signal cable (VGA or HDMI).

• Connect the USB touch line, otherwise the touch screen will not work
• For central control, please connect the RS485.
• Connect the power, when the light is bright, push the button of “up/fall back” to finish the Automatic elevation process. After that, you could push “up/down” button to adjust the angle as you want.

Central control code

Computer App control

• If required, please contact us for RS485 control software “Multifunctional-Lift Control Center V2.0 _win”。
• Prepare a converter of RS232 to RS485 or USB to RS485, and install the driver, connect all the lift which need to be control
• Download and install the software in English version, log in as admin with pass word 88888888, please adjust the langue and the correct COM after access in.
• Operate the assembly according to the app instruction

FAQ and Solutions

No.| Fault

phenomenon

| Reason
---|---|---

1

| ****

NO display

| Check the power on or off? Check the signal, is it

interrupted?

2

| ****

Character ambiguity

| Does it match with the computer resolution? Is it the contrast and brightness

adjustment correct?

3

| ****

Black screen

| It would turn off the brightness automatically without signal, Is brightness adjustment minimum? Long press of the “Auto” key may cause shutdown and the indicator to

turn red.

4| Invalid touch

function

| Make sure the USB connection

is correct or connect well

5

| The indicator is not on| Check if the fuse is damaged. If it is damaged, replace the fuse

with 3.15A specification.

---|---|---

Safety Pipe Location of National Standard Socket

• Subject to change without prior notice, the current production model shall prevail.
• For any enquiry, please contact our service center.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>