Kingsun Enterprises XYW1038 3 In 1 Wireless Charging Station User Manual

Kingsun Enterprises XYW1038 3 In 1 Wireless Charging Station

Product Information

Specifications

• USB output: 1A

Product Usage Instructions

Battery Installation: Galvanic Action

The product uses a CR2032 battery, which should be installed in the designated battery position.

Smart Watch Charging

Place the smart watch on the wireless charging area. The colorful indicator light will light up, indicating that the charging has started. When the charging is complete, the indicator light will go out.

Mobile Phone Charging

Place the wireless charging phone in the phone charging area for charging. The colorful indicator light will light up, indicating that the charging has started. When the charging is complete, the indicator light will go out.

Wireless Headset Charging

Place the wireless headset in the headset charging area for charging. The colorful indicator light will light up, indicating that the charging has started. When the charging is complete, the indicator light will go out.

Night Light

The product features a small night light. Press the small night light switch to turn it on or off.

Time Setting

1. In time mode, press and hold the key to switch between the 12-hour and 24-hour system.
2. The AM/PM icon is displayed in the morning or afternoon of the 12-hour system.

Alarm Settings

The product has an alarm function. Refer to the user manual for detailed instructions on setting up alarms.

FAQ

Is the phone not charging?

The phone may not be properly aligned with the charging coil or the wireless charger may not be plugged in properly.

Why does the charger heat up while charging?

It is normal for the charging coil to mildly heat up while charging a smartphone.

Why is the phone charging intermittently?

A. If the charging current of the adapter is not enough or the voltage is unstable, use a QC3.0 fast charging adapter to charge.

B. The charging position may not be aligned properly. Adjust the charging position for better electromagnetic induction.

Matters Needing Attention

1. If fast charging, use a UL or ETL certified 9V-2A (fast charging) power adapter. Use the included power cable. For standard charging, use a UL or ETL certified 5V-2A power adapter.
2. If the wireless charger overheats without any devices charging, unplug it completely to cool down.

RMJ Group International declares that radio equipment LAWC-2700 is in compliance with directive 2014/53/EU. The EU Declaration of conformity is available at: www.rmjgroup.com/docs

FCC Warning:
Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirements.

Diagram

1. When powered on, the indicator light will flash and then turn off, indicating that the product is on standby.
2. When placing the wireless charging phone separately in the phone charging area for charging, the colorful indicator light lights up and enters the charging state. Remove the charging product, the charging indicator light goes out, and the product enters the standby state.
3. Remarks: When the alarm goes off,it will continue until any button is pressed, or it will automatically turn off after 5 minutes.

Time Setting

1. In time mode: Press and hold the [MODE] key for 2 seconds to enter the time setting state. The “hour” flashes. Press the key to adjust the “hour”, press the key to adjust the “hour”, again press the [MODE] key to set the “minute”, press the key to adjust the “minute”, and press the key to adjust the “minute”; Long press and hold the key You can quickly adjust the time division and then press the [MODE] key again to complete the time setting. If there is no operation for 10 seconds, it will automatically return to the time mode and maintain the settings before returning.

12/24 Hour Conversion:

1. In time mode: Press and hold the key to switch to the 12/24 hour system:
2. The “AM/PM” icon is displayed on the morning/afternoon of the 12 hour system

Alarm Settings

1. In time mode, short press the [Mode] key to switch to alarm mode. At this point, the ‘AL’ icon will be displayed. Press and hold the [Mode] key for seconds to enter your desired time setting state. The “hour” flashes, press the key to adjust it up (hour), and press the key to adjust it down. Short press the [Mode] key to set the “minute” press the key to adjust the “minute” upwards, press the key to adjust the “minute” downwards, and long press the key to quickly adjust the time division setting and activate the alarm clock. Then again press the [Mode] key to complete the alarm, and the icon will light up.
2. In alarm mode, short press the key to turn the alarm on/off. After turning on the alarm clock, the icon will appear on any interface.
3. If there is no operation within 10 seconds, it will automatically return to time mode and keep the settings and alarm clock on or off before returning

Usage tips

Battery installation

Battery installation:

• Before use, please use the corresponding screwdriver to open and install the CR2032 battery as standard in the product, and then start powering on and using this product. galvanic action:
• The charger contains a CR2032 battery for time memory and only the time will remain active while the wireless charger is not plugged in.

Product parameters

Specifications

• Input TYPE-C interface Voltage: DC 5V 2A/9V 2A(QC 30W)
• PHONE Wireless Charger Output: 5W/7.5W/10W/15W
• AirPods Wireless Charger Output: 5W
• Apple Watch Wireless Charger Output: 3W
• USB-TYPE-C Cable length: 5FT/1.5M
• USB output: 1A
• Material: ABS+PC

Note: When using the wireless charger to charge 3 devices simultaneously, it is advisable to use a plug-in adapter above QC/ PD 30W to work at its best.

FAQ

Is the phone not charging?

The phone may not properly be aligned with the charging coil or the wireless charger may not be plugged in properly

Heats up while charging?

It is normal for the charging coil to mildly heat up while charging a smartphone.

Phone charging intermittently

A. lf the charging current of the adapter is not enough or the voltage is unstable, use a QC3.0 fast charging adapter to charge. B. The charging position is not aligned, and the electromagnetic induction is not good. The charging position should be adjusted.

Matters needing attention

1. If the product is being used for fast charging, please use a UL or ETL-certified 9V-2A (fast charging) power adapter. Use the included power cable for this product.
   If the product is being used for standard charging, use a UL or ETL-certified 5V-2A power adapter.

2. If the wireless charger is over heating while there are no devices charging, unplug it completely to cool down.

RMJ Group International declares that radio equipment LAWC-2700 is in compliance with directive 2014/53/EU.

The EU Declaration of conformity is available at: www.rmjgroup.com/docs

FCC

FCC Warning:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirements.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>