Hunter 41470 Ceiling Fan Seville II Instruction Manual

Hunter 41470 Ceiling Fan Seville II

Product Information

Specifications

• Model number: 4411447700
• Language options: English, Espanol, Deutsch, Francais, Italiano, Dansk, Suomi, Indonesian, Nederlands

Product Usage Instructions

Step 1: Reading the Manual
Be sure to read the entire manual before beginning installation and save any extra parts for future use.

Step 2: Installation and Assembly
This manual will help you install, operate, and maintain your new fan. These instructions are designed to make installation and assembly as simple and efficient as possible.

1. Each step is illustrated at the top of the page. The steps are numbered on the side of each illustration.
2. The letter labels in the illustration (example: [a]) identify the included parts and are described in the text instructions.
3. Text instructions beneath each illustration describe the procedure for each step.
4. On the right side of each image, you will find a life-sized illustration of necessary hardware.
5. At the bottom of each illustration, there is a small image that depicts the tools needed for each step. Each image correlates to the following legend:
6. Screwdriver, Phillips-head
7. Screwdriver, Flat-head
8. Drill with 3.5 mm bit or masonry bit (used only for concrete ceilings)
9. Wrench
10. Hammer
11. Tape Measure
12. SAE 7/16 Socket Wrench

Step 3: Maintenance
Regular maintenance is important to ensure the optimal performance of your ceiling fan. Please refer to the maintenance section of the manual for detailed instructions on cleaning and caring for your fan.

Frequently Asked Questions (FAQ)

• Q: What language options are available for this product?
  A: The product manual is available in English, Espanol, Deutsch, Francais, Italiano, Dansk, Suomi, Indonesian, and Nederlands.

• Q: What tools are needed for installation?
  A: The tools needed for installation include a screwdriver (Phillips-head and Flat-head), drill with a 3.5 mm bit or masonry bit (only for concrete ceilings), wrench, hammer, tape measure, and SAE 7/16 socket wrench.

• Q: How can I maintain my ceiling fan?
  A: Regular maintenance is important for optimal performance. Please refer to the maintenance section of the manual for detailed instructions on cleaning and caring for your fan.

Introduction and Preparation

Congratulations!
Your new Hunter ceiling fan is an addition to your home or office that will provide comfort and reliable performance for many years. We are proud to supply you with the best ceiling fan available anywhere in the world. Before installing your fan, we recommend that you record the following information for your records and warranty assistance. Refer to the Hunter nameplate on the top of your fan for the proper information. Be sure to save your receipt for your records.

Model Name|
---|---
Model Number|
Serial Number|
Date Purchased|
Place Purchased|

Before Installation
Before installing your fan, be sure you can do the following:

• Locate the ceiling joist or other suitable support in the ceiling.
• Drill holes and install wood screws or expansion anchors.
• If you have a concrete ceiling, you will need M5 x 30 mm expansion anchors and screws. (Sold separately)
• Identify and connect electrical wires.
• Lift 16 kg (40 lbs).

Site Selection and Preparation
Refer to the included booklet “Guide to Choosing and Preparing a Ceiling Fan Site” to determine the best location for your
fan. The booklet also includes information to ensure your fan support and outlet box meet applicable safety codes for ceiling fans.

Checking Your Fan Parts
Check your fan parts carefully. Unpack your fan parts as instructed by this manual to avoid damage. Be sure to save this manual for reference and save any extra parts. If you have a damaged fan blade, please return all blades for replacement. If you are installing more than one fan, be sure to keep the blades in sets, as shipped.

Optional Accessories

• Hunter offers several accessories to complement your fan such as wall-mounted or remote speed controls and extension down-rods for ceilings higher than 2,6 m. To ensure wobble-free and stable performance, all Hunter fans use 2 cm inner-diameter pipe for extensions. Follow the instructions for use and installation included with the Hunter accessory. If your fan does not include a light fixture, you may purchase an accessory light kit separately.
• For quiet and optimum performance of your Hunter fan, use only Hunter speed controls and accessories.

Using This Manual

How to Use This Manual:
Be sure to read the entire manual before beginning installation and save any extra parts for future use. This manual will help you install, operate, and maintain your new fan. These instructions are designed to make installation and assembly as simple and efficient as possible. Each step has four components:

1. Each step is illustrated at the top of the page. The steps are numbered on the side of each illustration.
2. The letter labels in the illustration (example: [a]) identify the included parts and are described in the text instructions.
3. Text instructions beneath each illustration describe the procedure for each step.
4. On the right side of each image, you will find a life sized illustration of necessary hardware. At the bottom of each illustration, there is a small image that depicts the tools needed for each step. Each image correlates to the following legend:

WARNING!

• To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. If you can not lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel.
• All wiring must be in accordance with national and local electrical codes. If you are unfamiliar with wiring, you should use a qualified electrician and not attempt to install the fan.
• To reduce the risk of personal injury, do not bend the blade attachment system when installing, balancing, or cleaning the fan. Never insert foreign objects between rotating blades.
• The fan blades cannot be placed lower than 2,3 m from the floor.
• The installation site must have an all-pole switch with a separation gap of at least 3 mm.
• Be sure to read this manual carefully before beginning installation and save these instructions for later reference or warranty assistance.
• To reduce the risk of personal injury, attach the fan directly to the support structure of the building according to these instructions and use only the hardware supplied.
• The appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure that they do not play with the appliance.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.

Installation

• Fan Mounting Options
  There are three different ways to mount your ceiling fan, depending on your needs and the style of your ceiling.

• Standard Mounting is the most common way to mount a ceiling fan. Standard mounting is recommended for ceilings 2,6 m or higher.

• Flush Mounting is used when the ceiling is less than 2,6 m high and fits closely to the ceiling.

• Angle Mounting is especially useful for vaulted or angled ceilings.

• If angle mounting, orient the ceiling plate with the arrows pointing toward the ceiling peak.

• If you have a concrete ceiling, follow steps 1-5 before proceeding to step 11. If you have a non-concrete ceiling, follow steps 6-10 before proceeding to step 11.

• For a concrete ceiling:
  Identify the supply mains in the ceiling and drill two holes using the ceiling plate [a] as a guide for measurement and accuracy.

• Drive the M6 x 30 mm expansion anchors [a] into the holes until the ends are flush with the ceiling.

• Place the three black rubber isolators [a] into the round ceiling plate holes [b].

• Thread the supply mains [a] through the center hole of the ceiling plate [b].

• Align two opposing oval slots in the ceiling plate [a] with the M6 x 30 mm expansion anchors [b]. Screw the matching M6 x 30 mm screws [c] into the anchors [b] until the isolators [d] are tight against the ceiling. Proceed to step 11.

• For non-concrete ceilings:
  Drill two pilot holes into the wood support structure using the ceiling plate [a] as a guide for measurement and accuracy.

• Place the three black rubber isolators [a] into the round ceiling plate holes [b].

• Place a flat washer [a] on both of the wood screws [b].

• Thread the supply mains [a] through the center hole of the ceiling plate [b].

• Raise the ceiling plate [a] and align two opposing oval slots with the pilot holes [b]. Insert and tighten the two wood screws [c] with washers [d] to secure the ceiling plate [a] to the ceiling.

• If you are using a standard or angle mounting style, follow steps 12-17 then skip to step 22. If you are using a flush mounting style, follow steps 18-21 before proceeding to step 22.

  • WARNING!
    To reduce the risk of fire, electrical shock, or motor damage, do not lift or carry the fan by the lead wires. To prevent damage to the wires on the bottom of the fan assembly, do not sit fan on hard surface. Use foam inside box as support. The pipe adapter has a special coating on the threads. Do not remove this coating; it prevents the pipe from unscrewing. Once assembled, do not remove the pipe.

• For standard or angle mounting:
  Pull the motor lead wires [a] through the pipe [b]. Screw the pipe into the fan motor [c] until tight then tighten the setscrew [d]. Threads on the pipe may be visible after tightening, this is normal.

• Slide the following parts onto the wires in this order: upper canopy [e], lower canopy [d], hanger bracket [c], Trilobular™ ball [b], and black wedge [a].

• Place the black wedge [a] around the top of the pipe [b].

• Align the openings in the wedge [a] with the holes in the pipe [b]. Insert the pin [c] through the holes to stabilize the wedge [a].

• Pull the Trilobular™ ball [a] up over the wedge [b] and allow the ends of the pin [c] to sit in the cutout area of the ball.

• Insert the positioning screw [a] into the Trilobular™ ball [b] and securely tighten. The top of the positioning screw [a] will rest on the wedge [c] and hold the ball in place. Proceed to step 22.

• For flush mounting: Remove the setscrew [a].

• Slide the following parts onto the wires in this order: upper canopy [a], lower canopy [b], hanger bracket [c], and low profile adapter [d].

• Place the low profile adapter [a] into the bottom of the hanger bracket [b] allowing the flat sides of each to fit together.

• Align the three cutouts in the low profile adapter [a] with the three holes in the top of the fan then install the three assembly screws
  [b]. Make sure the lower canopy is not trapped between the hanger bracket and the motor housing.

• Lift the fan and position the three tabs on the hanger bracket [a] with the three matching slots on the ceiling plate [b] then rotate counterclockwise to engage all three tabs.

• Temporarily thread an assembly screw [a] through the ceiling plate [b] into the hanger bracket [c] to prevent it from rotating.

  • WARNING!
    To avoid possible electric shock, before wiring the fan, disconnect power by turning off the circuit breakers to both the outlet box and its associated wall switch location. If you cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel. All wiring must be in accordance with national and local electrical codes. If you are unfamiliar with wiring, you should use a qualified electrician.

• Pull the supply mains [a] through the side of the hanger bracket [b].

• This is the procedure for steps 26-29. Thread the end of each wire into the terminal block [a] on the hanger bracket [b], then secure each supply main [c] by tightening the small setscrews [d].

• Attach the plug connector [a] from the terminal [b] on the hanger bracket [c] to the plug connector [d] on the fan wires [e].

• Excess wire may be placed into the outlet box [a] for non-concrete ceilings, or inside the hanger bracket [b] for concrete ceilings.

• WARNING!
  Be sure no bare wire or wire strands are visible after making connections. Failure to complete the following steps carefully could result in the fan falling.

• Remove the temporary screw [a] that was placed through the hanger bracket [b] and ceiling plate [c] but leave the holes in the hanger bracket [b] and ceiling plate [c] aligned.

• Raise the lower canopy [a] over the hanger bracket [b] and align the three holes of the lower canopy [a] with the previously aligned holes in the hanger bracket [b] and ceiling plate [c].

• Loosely install the three assembly screws [a] until all holes are properly aligned, then securely tighten each screw.

• Raise the upper canopy [a] and align the three holes on the upper canopy with the holes on the rim of the ceiling plate, then install and securely tighten the three assembly screws [b].

• Remove blade mounting screws [a] and shipping bumpers [b] installed on the motor. Save the screws and discard the shipping bumpers.

• Follow steps 38-39 if your fan includes grommets [a]. Skip to step 40 if your fan does not include grommets [a].

• If your fan includes grommets [a], place them in the fan blade holes by hand.

• Attach the fan blade [a] to the blade iron [b] using three blade assembly screws [c]. Repeat for all blades. Securely tighten all screws. Proceed to step 41.

• Attach the fan blade [a] to the blade iron [b] using three blade assembly screws [c]. Repeat for all blades. Securely tighten all screws.

• Loosely insert blade mounting screws [a] through the blade iron [b] into the fan until all fan blades [c] are spaced and attached. Securely tighten all screws.

• Partially thread two small assembly screws [a] into two of the three outermost holes on the switch housing mounting plate [b].

• Pull the upper plug connector [a] through the center of the upper switch housing [b].

• Place the keyhole slots in the upper switch housing [a] over the loosely threaded assembly screws [b] then rotate the switch housing [a] counterclockwise until the screws are situated in the narrow end of keyhole.

• Install the remaining small assembly screw [a] into the third hole and tighten all three securely.

• Attach the plug connector [a] from the motor housing [b] to the plug connector [c] on the lower switch housing [d].

• Place the lower switch housing assembly [a] over the upper switch housing [b] then align the holes of both housings and secure with three side screws [c].

Operating Your Hunter Fan

• How to operate your fan:
  • Turn on the electrical power to the fan.
  • Pull the chain slowly to adjust the setting.

1. The pull chain controls power to the fan. The chain has four settings in sequence: High, Medium, Low, and Off.

2. To change the direction of the airflow, turn the fan off and wait for it to come to a complete stop. Push reversing switch firmly left or right.

3. In warm weather, ceiling fans work best by blowing air downward (counterclockwise) providing the room with a cool breeze.

4. In cool weather, set your fan to draw air upward (clockwise) to distribute the warmer air trapped at the ceiling without causing a draft.

Cleaning and Maintenance

• Caring for finishes:
  For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish. A vacuum cleaner brush nozzle can remove heavier dust. Surface smudges or an accumulation of dirt and dust can be easily removed by using a mild detergent and a slightly dampened cloth. An artistic agent may be used, but never use abrasive cleaning agents as they will damage the finish.

• Caring for blades:

  • Wood finish blades should be cleaned with a furniture polish cloth. Occasionally, a light coat of furniture polish may be applied for added protection and beauty. Painted and high-gloss blades may be cleaned in the same manner as the fan finish.
  • If you need parts or service assistance contact your Hunter Fan retailer or visit out website at: http://www.hunterfanglobal.com .

Troubleshooting

• Problem: Nothing happens; fan does not move.
  Solution:

  • Turn power on, replace fuse, or reset breaker.
  • Loosen canopy, check all wiring connections.
  • Push reversing switch firmly left or right.
  • Pull chain switch.
  • Remove shipping bumpers.
  • Check the plug connection in the switch housing according to the directions.

• Problem: Noisy operation.
  Solution:

  • Tighten blade assembly and blade mounting screws until snug.
  • Replace all blades.
  • Check and tighten screws to the switch housing mounting plate and to the upper and lower switch housing.
  • Change to approved speed control.

• Problem: Excessive wobbling.
  Solution:

  • Use balancing kit included with fan.
  • Tighten all screws.
  • Make sure the fan is secure on the hanger bracket.
  • Turn power off, support fan very carefully and check that the Trilobular™ ball is properly seated.

If you have tried these troubleshooting solutions and still have trouble, visit our website at: http://www.hunterfanglobal.com .

References

• hunterfanglobal.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>