SIGNATURE HARDWARE 948943 Flush Mount Body Spray User Guide

: June 15, 2024
: Signature Hardware

Table of Contents

SIGNATURE HARDWARE 948943 Flush Mount Body Spray
Product Information
Installation Instructions
FAQ
FLUSH-MOUNT BODY SPRAY
BEFORE YOU BEGIN
GETTING STARTED
TOOLS AND MATERIALS
BEFORE INSTALLATION
INSTALLATION
CLEANING AND CARE
SHBS6010E Body Spray
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SIGNATURE HARDWARE 948943 Flush Mount Body Spray

Product Information

Flush-Mount Body

SKU: 948943, 948944

Specifications:

Dimensions: 4-7/16 – 4-3/4 (113 – 120 mm)
Distance between water supply system and finished wall: at least 2-9/16 (65 mm)
Distance between end point of the pipe and finished wall: 1-5/8 (41 mm) to 1-7/8 (48 mm)

Before You Begin:

We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for any damage to the faucet, plumbing, sink, countertop, or for personal injury during installation.

Observe all local plumbing and building codes.

Unpack and inspect the product for shipping damage. If any damage is found, contact our Customer Relations team at 1-855-715-1800.

Getting Started:

Ensure that you have gathered all the required materials that are needed for the installation.

For Warranty information, please visit: signaturehardware.com/services/warranty

Tools and Materials:

Phillips Screwdriver
Destornillador Phillips
Tournevis cruciforme

Installation Instructions

Step 1: Disassembling the Body Spray

The body spray comes from the factory fully assembled. You will need to disassemble it in order to begin installation.

Step 2: Positioning the Wall Hole

Make sure the distance between the water supply system and the finished wall is at least 2-9/16 (65 mm).

Reference the size to drill the wall as indicated in the provided dimensions.

Step 3: Connecting the Pipe

The distance between the end point of the pipe and the finished wall should be 1-5/8 (41 mm) to 1-7/8 (48 mm). Screw the pipe to the water supply fittings.

Note: Make sure the NPT thread is connected to water supply fittings.

Step 4: Installing the Plastic Box and Decorative Plate

Push the plastic box into the wall and install the decorative plate into the plastic box.

Step 5: Securing the Connector

Secure the connector into the pipe with a H10 hex wrench.

Install the body of the shower jet to the connector. Make sure the connector is fully inserted into the body.

Step 6: Installing the Outlet-Face Assembly

Install the outlet face assembly to the body. Make sure the outlet face is fully seated onto the body. Using a hex wrench, secure bolt #8 through the outlet face and into the body.

FAQ

Q: Where can I find warranty information?

A: For warranty information, please visit our website at signaturehardware.com/services/warranty.

FLUSH-MOUNT BODY SPRAY

BEFORE YOU BEGIN

We recommend consulting a professional if you are unfamiliar with installing plumbing ?xtures. Signature Hardware accepts no liability for any damage to the faucet, plumbing, sink, counter top, or for personal injury during installation.

GETTING STARTED

Ensure that you have gathered all the required materials that are needed for the installation.

For Warranty information, please visit: signaturehardware.com/services/warranty

TOOLS AND MATERIALS

BEFORE INSTALLATION

The body spray comes from the factory fully assembled. You will need to disassemble in order to begin installation.
Push the hole to remove the decorative plate.
Remove both bolts (#6 and #8) on the body jet face using a hex wrench. Then remove the outlet face.

INSTALLATION

Make sure the distance between the water supply system and the ?nished wall is at least 2-9/16” (65 mm).
Reference the size to drill the wall as below.
The distance between the end point of the pipe and the finished wall shall be 1-5/8″ (41 mm) to 1-7/8″ (48 mm). Screw the pipe to the water supply ?ttings.
Note: Make sure the NPT thread is connected to water supply settings.
Remove the pipe and wrap plumbers’ tape around the end of the pipe. Place the pipe back onto the water supply setting.
Turn on the water supply system to flush the pipe. Then close the water supply system.
Push the plastic box into the wall.
Note: Make sure the “UP FACE” marking is facing up.
Install the decorative plate into the plastic box.
Secure the connector into the pipe with a H10 hex wrench.
install the body of the shower jet to the connector.
Note: Make sure the connector is fully inserted into the body.
Secure bolt #6 into the body. Make sure the body and the connector are tight, using a hex wrench.
Install the outlet face assembly to the body. Make sure the outlet face is fully seated onto the body. Using a hex wrench, secure bolt #8 through the outlet face and into the body.
Note: Do not overtighten.
Tighten and screw the outlet face and the decorative plate together make sure both plates are slightly at an angle.
Note: Ensure the holes are lined up.

Note: The product be can be adjusted to different angles.

CLEANING AND CARE

Do not use abrasive sponges or microbead cloths, corrosive cleansers, solvents or acids. We recommend that you do not use any anti-limescale products or cleaners containing vinegar or acetic acid. Chemical cleaning agents may damage the product. Clean products using only mild soap and a wet cloth.