Dahao PRO6 TWS Wireless Binaural Stereo Music Headphones User Manual
- June 15, 2024
- Dahao
Table of Contents
Dahao PRO6 TWS Wireles Binaural Stereo Music Headphones
Specifications
- Model: TWS
- Connectivity: True wireless connectivity (TWS)
- Supported Agreements : A2DP1.3/HIFI1.6/HFP1.6/AVRCP1.6/HSP1.2
- Transmission Distance: 8 meters
- Frequency: 2.4 GHz
- Power Reading: Yes
- Headphone Charging Time: 1.5 hours
- Label: FCC ID: 2BDPV-PRO6
Wireless Binaural
Stereo music headphones
Parameter configuration
True wireless connectivity (TWS) to achieve wireless stereo, left and right
channel separation, HIFI audio, left and right ears have a full bluetooth
function, can be used alone or in pairs
Note : the product parameters will be different according to the machine
type, usage mode, environment and so on.
Support Agreement: | A2DP1.3/HIFI1.6/HFP1.6/AVRCP1 .6/HSP1.2 |
---|---|
Transmission distance: | 8M |
Frequency: | 2.4G |
Power reading: | YES |
Headphone charging time | 1.5H |
Charging Time: | 1.5H |
Charge
-
When the headset is charged, the indicator light is always bright, and when the headset is full, the indicator light turns off
The charging indicator lights flash when the charging bin is charged, and it always lights when it is full. -
This product built-in non-removable rechargeable battery, charging mode for external wire charging.
-
Charging current 1A voltage 5V, can not use more than 5V1A charger to charge the product.
-
It takes about 1.5 hours for the Bluetooth headset/charging dock to be fully charged.
-
When the power of the Bluetooth headset is too low, the headset will send out an alert sound to remind the user to charge it at regular intervals.
- Power off-Take out the earphone, earphone automatic boot pair, long press the earphone 3 seconds to hear the“Power off” sound.
- Pair-Put the headphones into the charging automatic shutdown, you can also press the headphones 5 seconds to hear the“connected” sound
- Play pause-click any headset
- Listen to the phone-click any headset
- Hang up-click any headset during a call
- Reject calls-press any headset for 2 seconds
- Last song-double click on the ear
- Next track-double click on the main ear。
- Increase volume-three clicks on the main ear
- Volume reduction-three clicks to the ear pair
- Voice assistant-press any headset for 3 seconds
- Auto-reconnect-just turn it on, there must be a matching record before
Function introduction
- Power on-take out the headphone from the charging bin.
- The headphone will automatically turn on and pair. You can also press the multi-function key of the headphone for 3 seconds to hear the“Power on” sound.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
-
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and -
, if not installed and used in accordance with the instructions, may cause harmfulinterference to radio communications.
-
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.
- Consult the dealer or an experienced radio/TV technician for help
Note : The Grantee is not responsible for any changes or modifications
not expressly approved by the party responsible for compliance. such
modifications could void the user’s authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirement.
This equipment complies with FCC’s RF radiation exposure limits set forth for
an uncontrolled environment. This device and its antenna(s) must not be
colocated or conjunction with any
other antenna or transmitter.
Label
- FCC ID : 2BDPV-PRO6