Senmeo AC-018JR Bladeless Fan and Heater User Manual
- June 15, 2024
- Senmeo
Table of Contents
User MANUAL Bladeless Fan & Heater
AC-018JR Bladeless Fan and Heater
MODEL: AC-018JR
uk-support@senmeo.com
Thanks for Choosing Senmeo!
Your support means the world to us. We hope you enjoy our product as much as
we did creating it.
EXTEND YOUR WARRANTY FOR FREE
In the unlikely event of a product failure, we offer a 12-month warranty for
peace of mind.
In addition, we will extend the warranty period for another 12 months if you
provide us with your order number via e-mail (uk-support@senmeo.com).
uk-support@senmeo.com
www.senmeo.com
IMPORTANT SAFETY INSTRUCTIONS
| To reduce the risk of electric shock or personal injury, the following basic
precautions should be strictly observed when using electrical products.
---|---
| WARNING: Do not cover the heater. There is a risk of overheating.
| Do not use the fan heater near combustible materials!
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
-
Read all instructions before using this heater.
-
This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater.
Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front of the heater and keep them away from the sides and rear. -
Always unplug heater when not in use.
-
Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
-
Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner.
-
Do not use outdoors.
-
Never locate heater where it may fall into a bathtub or other water container.
-
Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
-
To disconnect heater, turn controls to off, then remove plug from outlet.
-
Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
-
To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked. A heater has hot and arcing or sparking parts inside.
Do not use it in areas where gasoline, paint, or flammable liquids are used or stored. -
Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
-
Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).
-
If there is a loose fit between the plug and the socket or the plug becomes very hot, the socket may need to be replaced. Check with a qualified electrician to replace the socket.
-
It is normal for the plug and cord to feel warm to the touch. A plug or cord which becomes hot to the touch or becomes distorted in shape may be a result of a worn electrical outlet. Worn outlets or receptacles should be replaced prior to further use of the heater. Plugging the heater into a worn outlet / receptacle may result in overheating of the power cord or fire.
-
The output of this heater may vary and its temperature may become hot enough to burn exposed skin. Use of this heater is not recommended for persons with a high sensitivity to heat or an inability to react to avoid burns.
-
Ensure the heater is on a stable, secure surface to eliminate the potential of tipping it over.
-
Make sure that no pieces of polystyrene or other packaging material have been left between elements of the appliance. It may be necessary to pass over the appliance with a vacuum cleaner.
-
Do not attempt to modify or repair the product by yourself. Doing so could void the warranty and cause damage or personal injury. Only a repair technician may disassemble or repair this product.
-
Choking hazard – This remote control unit contains a small battery.
Keep the remote control away from children and do not swallow the battery. If the battery is swallowed seek medical advice at once. -
If the machine is not working as it should, has received a sharp blow, has been dropped, damaged, left outdoors, or dropped into water, do not use and contact Customer Support.
NOTE: There may be a trace of smoke or odor when the unit is first
operated. This indicates that a drop of oil fell on the heating coil during
the manufacturing process. It will quickly evaporate and should not re-occur.
FOR HOUSEHOLD USE ONLY READ AND SAVE THESE INSTRUCTIONS
Check the appliance regularly and refer to TROUBLESHOOTING or contact our
customer support if it shows any of the following signs:
- Power cord or plug is damaged.
- Unsaual smell or excessive heat.
Specifications
| Model | AC-018JR |
|---|---|
| Product Size | 151555cm |
| Rated Power | 1100W |
| Input | AC 220-240V 50/60Hz |
| Remote Control Battery | CR2025, 3V |
HOT SURFACE
THE FRONT SURFACE CAN BE VERY HOT DURING USE.
DO NOT TOUCH WHEN IN USE.
USE YOUR HEATER
Package Contents：
1 x Bladeless Fan & Heater
1 x Remote Control
1 x User Manual
Product Diagram
Display and Touch Key
Note:The display is not only the screen but also the operating buttons.
Power ON/OFF
-
Tap the touch key to enter the cooling operation mode; the fan is at speed level 5 by default upon initial starting after restoration of power if the power has been disconnected.
-
Tap the touch key to start the fan, and the air flow speed corresponds to the speed level before the fan enters the ready mode.
-
Press and hold the touch key for 4 seconds to turn it off.
-
To prevent the body from overheating, the heater blows cold air to cool the body for 30 seconds after it is turned off in heating mode.
Heating Mode -
In the ready mode, long press the touch key for 3 seconds to enter the heating mode; in this mode, digits in the LED display will flash.
-
In the heating mode, tap the touch key to adjust the heating level cyclically from 1-3.
Cooling Mode -
Tap the touch key to enter the cooling mode; the fan is at speed level 5 by default upon initial starting after restoration of power if the power has been disconnected.
-
Tap the touch key to start the fan, and the air flow speed corresponds to the speed level before the fan enters the ready mode.
-
Tap the touch key on the main unit to adjust the speed level cyclically from level 1-8, H, L.
Oscillation Function -
In the operating mode, press and hold the touch key for 2 seconds to enter the oscillation function, plus the fan starts to oscillate 90°left and right;
-
Again press and hold the touch key for 2 seconds to cancel the oscillation.
Remote Control
Note: All the functions can be achieved through the buttons on the remote
control.
Operations and Functions
Place the heater on a firm, level surface free from obstructions, and at least
3ft. (0.9m) away from any wall or combustible material. Plug into an
appropriate voltage AC 220-240V outlet, The unit will enter standby mode with
a beep. Your heater is ready for use now.
| Power ON/OFF
• Press the On/Off button to enter the cooling operation mode; press the
button again to turn off the fan.
• Press the On/Off button to enter the cooling operation mode; it is at speed
level 5 by default upon initial starting after restoration of power if the
power has been disconnected or at the speed level before the fan enters the
ready mode if the power has not been disconnected.
---|---
| Heating button
• In the cooling mode, press the Heating button to switch to the heating mode;
in the heating mode, digits in the LED display flash; at this time, the heater
level can be adjusted by using the red +-buttons.
| Cooling button
• In the heating mode, press the Cooling button to switch to the cooling mode;
at this time, the air flow can be adjusted by using the white +- buttons.
| High button
• Press this button to enter the High mode; in this mode, the fan produces the
maximum air force and the LED display shows “H”.
• The button is inactive in the heating mode.
| Oscillation Button
• When the fan is in the operating mode, press this button for once to turn on
oscillation, and press it again to turn off oscillation.
| Timing button
• Press this button to enter the Timing mode, in which the fan can be set to
run for a fixed time of 0-9 hours. When 0 is set, it means the timing function
is turned off.
• The flashing dot on the LED display indicates in the timed state.
| • Press this button to enter the Sleep mode;in this mode, the fan running
on low speed and the LED display shows ”L”.
• Sleep mode button
• The button is inactive in the heating mode.
| Mute button
• Press the button for once to turn off the machine beeps; press the button
again to turn on the machine beeps.
| • The buttons are used to adjust the cooling air flow speed from level 1-8.
• These buttons are inactive in the heating mode. White +- buttons
| Red +- buttons
• The buttons are used to adjust the heating speed from level 1-3.
• These buttons are inactive in the cooling mode.
Other Featrues
Memory Function| • The heater is designed with memory function. It will always
remember your last settings (modes, speeds) once you turn it on again.
• This function is only available when the power plug is not unplugged. If the
power plug is reconnected, the default setting is 1-speed hot air.
---|---
Auto LED Display OFF| • If no operation is done within 30 s. after powered on,
the display will turn off automatically .
• To turn the display back on, press any button to wake it up.
Tip-Over Protection| • In heating mode, the body is tipped over, which
automatically turns off the heating function.
• In cold air mode, tipping has no effect.
Replacement of Batteries NOTE: The red indicator light at the top of the remote will light up when any button on the remote is pressed. If the indicator light on the remote control no longer lights up, replace the batteries.
- Press the locking button and then pull out the battery holder.
- Replace the battery with the same type (CR2025 3V), making sure the (+) side facing up.
- Push in the holder until securely locked into place.
Caution
Chemical Burn and Choking Hazard. Keep batteries away from children.
- This product contains a lithium button/coin cell battery. If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
- Dispose of cells properly and keep away from children.
Even used cells may cause injury.
CLEANING AND MAINTENANCE
We recommend cleaning the heater at least once during the operating season and
before the off season. This will ensure optimal performance.
Always disconnect the appliance from the mains by switching it
off and removing the plug from the power outlet before cleaning.
-
Use only a soft cloth to gently wipe the outer surfaces of the heater clean.
-
Do not use any cleaning agents or detergents.
-
Never immerse the heater in water and never allow water to drip into the motor housing. Be sure not to wet the heating element and the switches.
-
For storage, you may leave the heater covered to protect it from dust. Store it in a cool, dry location and arrange the cable away from traffic areas so that it will not be tripped over or damaged.
Caution： -
Do not allow water to run into the interior of the heater as this could result in a fire or electric shock hazard.
-
Any other servicing should be performed by an authorized service representative.
-
Except cleaning, any other servicing should be performed by an authorized service representative.
-
Carefully fold the power supply cord and tie it up with a cord, then put the heater into the packing box. Keep it in a cabinet away from any hot or wet location.
TROUBLESHOOTING
The following troubleshooting guide addresses the most common problems. If problems persist, contact the Customer Support at uk- support@senmeo.com.
| Problem | Possible Causes | Solution |
|---|---|---|
| Malfunction Codes on LED Display | E1 – Excessive current | Unplug and retry, |
if this does not work contact customer support.
E2 – Motor blocking protection| Unplug and retry, if this does not work
contact customer support.
E3 – Motor phase loss protection| Unplug and retry, if this does not work
contact customer support.
E4 – High or low voltage protection| Unplug and retry, if this does not work
contact customer support.
Heater does not start| Power cord is not properly plugged in.| Connect the
plug to a powered electrical outlet.
No power is passing through the unit.| Ensure that your circuit breaker or
fuse is working properly.
Ensure your heater is placed on a flat and even surface.
The heater suddenly stops during heating.| The heater is tipped over| Place it
on a flat, level and stable surface.
The remote control does not work.| The battery is drained.| Replacing the
battery.
The battery is installed in the wrong direction.| Make sure the battery is
installed with the “+” sign facing up.
If it still does not work after replacing the battery, please contact customer
service.
WARRANTY AND SERVICE
Default 12-Month Warranty
This product is covered with Senmeo product and labor warranty for 12 months
from the date of its original purchase.
Extend Your Warranty
Contact us by email (uk-support@senmeo.com)
with the correct order number and the warranty will be extended for a further
12 months.
The warranty will not apply in cases of:
- Accident, misuse, or repairs performed by unauthorized personnel.
- Any unit that has been tampered with or used for commercial purposes.
- Normal wear and tear of wearable parts.
- Use of force, damage caused by external influences.
- Damage caused by non-observance of the User Guide, e.g. connection to an unsuitable mains supply or non-compliance with the instructions.
- Partially or completely dismantled appliances.
- Defects caused by or resulting from damages from shipping or from repairs, service, or alteration to the product or any of its parts that have been performed by a repair person not authorized by Senmeo.
We can only provide after-sales service for products that are sold by Senmeo
or Senmeo authorized retailers and distributors. If you have purchased your
unit from a different place, please contact your seller for return and
warranty issues.
We’re Here to Help!
uk-support@senmeo.com
Zhejiang Youmeilai Intelligent Technology Co., Ltd.
- Please have your order confirmation number ready before contacting Customer Support.
www.senmeo.com
Senmeo AC-018JR
We’re Here to Help!
Contact our customer support!
uk-support@senmeo.com
www.senmeo.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>