AMIR B0BNMJCYDJ Precise Electric Screwdriver User Guide

Precise Electric Screwdriver
User Guide

B0BNMJCYDJ Precise Electric Screwdriver

For the first time use:
a) Check All Components: Ensure all parts, including bits and accessories, are present and intact. Make sure they are tightened before use. Check the switch to see if it is stuck by a foreign object.
b) Read the User Manual and video: Familiarize yourself with the product’s features, safety instructions, and operational guidelines.
c) Initial Inspection: Examine the electric screwdriver for any visible damages or defects.
d) Test in a Safe Environment: Before using it on a project, test the screwdriver in a safe, clear area to understand its handling and power.
e) Adjust Settings as Needed: Based on your task, adjust torque settings and choose the appropriate bit.
f) The Precision electric screwdriver is designed for repairing and disassembling electronic products, watches, smartphones, computers, and similar devices, and is not intended for use in furniture, home renovation, or similar domestic settings. It can only be used for precision repair scenarios, not suitable for home improvement, drilling and other scenarios.

Using Steps

1. Ensure a full charge
2. Press ③, tighten the screws.
3. Press ④, loosen the screws.
4. Press ⑤, turn on the light, Press again, turn off the light.
5. There is a Type-C USB charging port at the end of the screwdriver.

Product Specification

• Voltage: 3.7V- DC
• Battery Type: Li Battery
• Form Factor: 2136433mm
• Manual Torque: 3N.m
• Electric Torque: 0.25 – 0.35N.m
• Net Weight of the Screwdriver: 54g
• Battery Capacity: 350mAh
• Charging Time: <50mins
• Free Speed: 180/min
• Net Weight: 256g

Charging Instruction

1. When using the Type-C USB charging port, the charging indicator shows white means charging”, shows green means “full charge”.
2. Please charge the screwdriver fully and the charging time is no more than 2.5 hours before when the screwdriver the first time.

Charging Requires Attention to the Following

a) Use the Correct Charger: Always use the charger provided with the screwdriver or one that matches the manufacturer’s specifications. (Only charge the screwdriver by using the provided charging cable.)
b) Monitor Charging Time: Avoid overcharging; remove the screwdriver from the charger once it’s fully charged. (Please charge the screwdriver at least once a month to maintain a good performance.)
c) Charging Environment: Charge in a cool, dry place away from direct sunlight and heat sources.
d) Check for Damage: Before charging, inspect the charger and battery for any signs of damage.
e) Avoid Using While Charging: For safety and battery health, do not use the screwdriver while it’s charging.
f) Store Properly after Charging: Once charged, unplug the charger and store the screwdriver in a safe, dry place.

Safety Warm Tip

Warning! Please read all the provided safety warm tips, specifications, pictures and provision.

Electrical Safety

1. Please charges the screwdriver by using the provided charging accessories, don’t use others, for reduce the risk when charging.
2. Please don’t put screwdriver expose under the sun or in the wet situation.
3. If you can’t avoid putting the screwdriver in the wet situation, please wear the silicone sleeves to reduce risk.
4. If using the electric screwdriver in the electrostatic environment, install an electrostatic ring to demagnetize the driver bits to reduce operation accidents.

Personal Safety:

1. There is a little dangerous of the electric screwdriver, please do not let the babies or children use it to avoid injury.
2. Please don’t put it in the pockets or bags to avoid operate the electric screwdriver accidentally causing injury.
3. When operating the electric screwdriver, the holding height could not be too high or too low ensure that the electric screwdriver can be controlled under other external force.

Using Precaution

1. When using the electric screwdriver to remove screws, please use the manual mode to loosen the screws avoid destroy screws and other parts at screws.
2. When not using the electric screwdriver, please put it out of the reach of the children.
3. If the product falls into the water or splashes into the machine, please stop using it to avoid short circuit.
4. When maintain the electric screwdriver, please check the smoothness of the screwdriver head rotation, whether other parts are damaged, etc. If there are some damages, please repair it before using. Using the damaged electric screwdriver may cause accidence.
5. When the fastener or the hidden wire operation may be touched, the electric screwdriver should be held by the holding surface of the insulator.
6. Don’t disassemble this product.
7. Please follow the instructions.

Maintenance

1. Ask professional maintenance staffs to use the same spare parts to repair the electric screwdriver. This will ensure the safety of the electric screwdriver being repaired.
2. Never repair the damaged battery pack. The battery pack just could be repaired by the producer or the authorized service providers.

Built-in battery safety warning

1. Don’t disassemble, open or shred tools.

2. Don’t put the electric screwdriver expose to the heat or flame. Avoid keep it under direct sunlight.

3. Don’t short-circuit the exposed terminals. Don’t put several tools in a box or drawer to avoid Short-circuiting between them or being short-circuited by other metal objects.

4. Once the battery expose, don’t make the leaked liquid touch your skin or eyes. If touch, wash the touched part with plenty of water and then go to the hospital in time.

5. Don’t use non-specified adapters.

6. Don’t use non-device-specific batteries.

7. Keep the tool clean and dry.

8. If the charging port is dirty, please use the dry cloth to wipe.

9. Please charge the electric screwdriver before using.
   You should use the correct charger to charge and refer to the manufacturer’s instructions or the correct instructions in the manual.

10. Please don’t charge the tools for a long time.

11. After a long-term storage, the tool needs to be charged and discharged several times to obtain the best performance.

12. Using at the normal temperature: 20°C- ±5°C, the battery has the best performance.

13. Correct battery disposal.

Warranty Description

Product performance malfunction

The charging indicator doesn’t light up when charging.
The switch buttons can’t be used.
The body is cracked due to structural or material factors.
The bit drops usually when used correctly.

1. Within 12 months from the date of receipt, if the product has the situation shown in the product performance malfunction table, the maintenance service can be enjoyed for free confirmed by the service center.
2. Within 7 days from the date of sale, if it is determined to be a malfunction shown in the product performance malfunction table, you can enjoy free return or exchange services.

The following conditions are not within the warranty period

1. Unauthorized repair, misuse, collision, negligence, abuse, fluid intake, accident, alteration.
2. Use other product accessories or tear up, alter labels, or anti-counterfeiting marks.
3. The warranty period has expired.
4. Damaged by force majeure.
5. The product and its accessories have performance malfunction due to human errors.

Troubleshooting

Q: What is the maximum torque for this product? Is it powerful enough?

A: The electric torque of this product is 0.25- 0.35N.m and the manual torque is 3N.m. If you need a big torque, switch to manual mode.

Q: How long is the charging time?

Q: What size is this screwdriver and how much does it weigh?

A: The screwdriver measures 2136433 mm and has a net weight of 54 grams.

Q: What can I do if my electric screwdriver doesn't work?

A: First check if the electric screwdriver has enough power to work, if not, please fully charge the screwdriver first. Secondly, check whether the switch is stuck by foreign objects, and whether the electric screwdriver has obvious damage or defective condition. After checking it and it still doesn't work, please contact us, we are always ready to answer your questions.

Q: The electric screwdriver stops after it starts drilling and won't continue drilling, why is that?

A: Sorry, this Precision electric screwdriver is designed for repairing and disassembling electronic products, watches, smartphones, computers, and similar devices, and is not intended for use in furniture, home renovation, or similar domestic settings. It can only be used for precision repair scenarios, not suitable for home improvement, drilling and other scenarios.

Q: What is the blue stick for?

A: It's used to open various electronics like phones, etc.

Q: Will the bits work for eyeglass repairs?

A: Yes, it has a standard and Phillips bits that will do most eyeglass screws.

Q: What is the material for the tips?

A: Tool steel.

Q: Does it come with a USB cable?

A: Yes, the package includes 24 precision professional drill bits, 1 electric screwdriver handle, 1 plastic pry bar, 1 magnet and 1 USB cable.

Q: How long can I use it on a single charge?

A: This computer, phone repair tool kit Built-in a rechargeable battery, 300 screws can be punched after a fully charged.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>