SONOFF TX-US V1.5 Wi-Fi Smart Wall Switch User Manual

TX US
User  manual V1.5 Wi-Fi Smart Wall Switch

Operating Instruction

1. Power off
   Please install and maintain the device by a professional electrician. To avoid electric shock hazard, do not operate any connection or contact the terminal connector while the device is powered on!

2. Wiring instruction
   Make sure the neutral wire and live wire connection is correct.
   To ensure the safety of your electrical installation, it’s essential either a Miniature Circuit Breaker (MCB) or a Residual Current Operated Circuit Breaker (RCBO) with an electrical rating of 2A(1 gang)/4A(2gang)/6A(3gang) has been installed before the switch.

3. Equipment Installation

4. Download the eWelink APP
   

5. Power on
   After powering on, the device will enter the quick pairing mode during the first use.
   The Wi-Fi LED indicator changes in a cycle of two short and one long flash and release.
   The device will exit the quick pairing mode if not paired within 3mins. If you want to enter this mode, please long press any configuration button for about Ss until the Wi-Fi LED indicator changes in a cycle of two short and one long flash and release.

6. Add the device
   Tap “+” and select “Add Device”, then operate following the prompt on the APP.

Compatible Pairing Mode

If you fail to enter Quick Pairing Mode, please try”Compatible Pairing Mode “to pair.

1. Long press Pairing button for Ss until the Wi-Fi LED indicator changes in a cycle of two short flashes and one long flash and release. Long press Pairing button for Ss again until the Wi-Fi LED indicator flashes quickly. Then, the  device enters Compatible Pairing Mode.
2. Tap”+” and select “Add Device”, then operate following the prompt on the APP.

Pairing and Clearing with RF Remote Controller

The switch supports the remote controller with 433. 92MHz frequency brand to turn on/off, and each channel can learn it independently, which is local short-range wireless control not Wi-Fi control.
Pairing Method:
Long press the touch button you want to pair for 3s until the indicator flashes “red” and release, then short press the corresponding button on the RF remote controller and you will see the indicator flashes “red” again after successful  pairing. Other buttons can be paired through this method.
Clearing Method:
Long press the touch button you want to clear for Ss until the indicator light flashes “red” twice and release, then short press any button on the RF remote controller and you will see the indicator flashes “red” again after successful clearing. Other buttons can be cleared through this method.

Specifications

Model| TOUS1 C/TOUS2C/TOUS3C
T2US1C/T2US2C/T2US3C
T3US1 C/T3US2C/T3US3C
---|---
Max. input| TO/T1 /T2/T3( US1 C ): 100-240V.N., 50/60Hz 2A Max p
TO/T1/T2/T3( US2C ): 100-240V-,-, 50/60Hz 2A/gang 4A Total Max p
TO/T1 /T2/T3( US3C ): 100-240V— 50/60Hz 2A/gang 6A Total Max p
LED load| 150W@110V(per channel) , 300W@220V(per channel)
Wi-Fi| IEEE 802.11 b/g/n 2.4GHz
RF| 433.92MHz (Receive only)
Operating systems| Android & iOS
Materials| PC +tempered glass panel
Dimension| 120x74x38mm

T0(US1 C/US2C/US3C) does not support the remote controller with 433.92MHz.

Product Introduction

The device weight is less than 1 kg.
The installation height of less than 2 mis recommended.

Wi-Fi LED indicator status instruction

Features

Turn on/off the I ight or fan from anywhere, schedule it power on/off and share it with your family to control together.

Factory Reset

Long press any button you desired to pair for about 5s until the Wi-Fi LED indicator changes in a cycle of two short and one long flash and release, then the reset is successful. The device enters quick pairing mode.

Please reset the switch to factory defaults if you want to use other Wi-Fi networks, then reconnect the network.

Common Problems

Q: Why my device stays “Offline”?
A: The newly added device needs 1-2mins to connect Wi-Fi and network. If it stays offline for a long time, please judge these problems by the blue Wi-Fi indicator status:

1. The blue Wi-Fi indicator quickly flashes once per second, which means that the switch failed to connect your Wi-Fi:
   CD Maybe you have entered a wrong Wi-Fi password.
   1. Maybe there’s too much distance between the switch your router or the environment causes interference, consider getting close to the router. lffailed, please add it again.
   3 The 5G Wi-Fi network is not supported and only supports the 2.4GHz wireless network.
   2. Maybe the MAC address filtering is open. Please turn it off.
   3. If none of the above methods solved the problem, you can open the mobile data network on your phone to create a Wi-Fi hotspot, then add the device again.

2.  Blue indicator quickly flashes twice per second, which means your device has connected to Wi-Fi but failed to connect to the server.
   Ensure steady enough network. If double flash occurs frequently, which means you access an unsteady network, not a product problem. If the network is normal, try to turn off the power to restart the switch.

FCC compliance statement

1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
   (1) This device may not cause harmful interference, and (2) This device must accept any interference received, includinginterference that may cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
   Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the  user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

RACCOLTA DIFFERENZIATA

ISED Notice

This device contains licence-exempttransmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
   This device must accept any interference, including interference that may cause undesired operation of the device.
   This Class B digital apparatus complies with Canadian ICES – 003(8).
   This device complies with RSS 247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference.

For CE Frequency

EU Operating Frequency Range:
Wi-Fi: 802.11 b/g/n20 2412-2472MHz,
EU Output Power:
Wi-Fi2.4G<20dBm
SRD: 433.92MHz (Receive Only for T2US1C, T2US2C, T2US3C, T3US1C, T3US2C, T3US3C)

SAR Warning
Under normal use of condition, this equipment should be kept a separation distance of at least 20 cm between the antenna and the body of the user.

EU Declaration of Conformity
Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio equipment type T0US1 C, T0US2C, T0US3C, T2US1 C, T2US2C, T2US3C, T3US1 C, T3US2C, T3US3C is in compliance with Directive 2014/53/EU.The full text of the EU declaration of conformity is available at the following internet address: https://sonoff.tech/complianee/

WEEE Disposal and Recycling Information

All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the  environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and  conditions of such collection points.

Shenzhen Sonoff Technologies Co., Ltd.
1001, BLDG8, Lianhua Industrial Park, shenzhen, GD, China
ZIP code: 518000
Website: sonoff.tech
MADE IN CHINA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>