SONOFF TO-T1 Wi-Fi Smart Wall Switch User Manual
- June 15, 2024
- SonOFF
Table of Contents
User manual V1.3 Wi-Fi Smart Wall Switch
SONOFF TECHNOLOGIES CO., LTD.
Operating Instruction
-
Power off Please install and maintain the device by a professional electrician. To avoid electric shock hazard, do not operate any connection or contact the terminal connector while the device is powered on!
-
Wiring instruction Make sure the neutral wire and live wire connection is correct.
To ensure the safety of your electrical installation, it’s essential either a Miniature Circuit Breaker (MCB) or a Residual Current Operated Circuit Breaker (RCBO) with an electrical rating of 2A(1 gang)/4A(2gang)/6A (3gang) has been installed before the switch. -
Equipment Installation
-
Download the eWeLink APP
-
Power onAfter powering on, the device will enter the quick pairing mode during the first use.
The Wi-Fi LED indicator changes in a cycle of two short and one long flash and release.
The device will exit the quick pairing mode if not paired within 3mins. If you want to enter this mode, please long press any configuration button for about 5s until the Wi-Fi LED indicator changes in a cycle of two short and one long flash and release. -
Add the deviceTap “+” and select “Add Device”, then operate following the prompt on the APP.
Compatible Pairing Mode
If you fail to enter Quick Pairing Mode, please try “Compatible Pairing Mode” to pair.
- Long press Pairing button for 5s until the Wi-Fi LED indicator changes in a cycle of two short flashes and one long flash and release. Long press Pairing button for 5s again until the Wi-Fi LED indicator flashes quickly. Then, the device enters Compatible Pairing Mode.
- Tap “+” and select “Add Device”, then operate following the prompt on the APP.
Pairing and Clearing with RF Remote Controller
The switch supports the remote controller with 433.92MHz frequency brand to turn on/off, and each channel can learn it independently, which is local short-range wireless control not Wi-Fi control.
Pairing Method:
Long press the touch button you want to pair for 3s until the indicator
flashes “red” and release, then short press the corresponding button on the RF
remote controller and you will see the indicator flashes “red” again after
successful pairing. Other buttons can be paired through this method.
Clearing Method:
Long press the touch button you want to clear for 5s until the indicator
light flashes “red” twice and release, then short press any button on the RF
remote controller and you will see the indicator flashes “red” again after
successful clearing. Other buttons can be cleared through this method.
Specifications
Model| TOUK1 C/TOUK2C/TOUK3C
T1UK1C/T1UK2C/T1UK3C
T2UK1C/T2UK2C/T2UK3C
T3UK1 C/T3UK2C/T3UK3C
---|---
Rating| TO/T1 /T2/T3( UK1C ): 100-240V ∼ N– 50/60Hz 2A Max p
TO/T1/T2/T3( UK2C ): 100-240V ∼ 50/60Hz 2A/gang 4A Total Max μ
TO/T1 /T2/T3( UK3C ): 100-240V ∼ 50/60Hz 2A/gang 6A Total Max μ
LED load| 150W@110V(per channel), 300W@220V(per channel)
Wi-Fi| IEEE 802.11 b/g/n 2.4GHz
RF| 433.92MHz (Receive only)
Operating systems| Android & iOS
Materials| PC + tempered glass panel
Dimension| 86×86×35mm
T0 (UK1C/UK2C/UK3C)does not support the remote controller with 433.92MHz.
Product Introduction
The device weight is less than 1 kg.
The installation height of less than 2 mis recommended.
Wi-Fi LED indicator status instruction
Wi-Fi LED indicator status | Status instruction |
---|---|
Flashes (one long and two short) | Quick Pairing Mode |
Flashes quickly | Compatible Pairing Mode |
Keeps on | Device is connected successfully |
Flashes quickly once | Unable to discover the router |
Flashes quickly twice | Connect to the router but fail to connect to Wi-Fi |
Flashes quickly three times | Upgrading |
Features
Turn on/off the light or fan from anywhere, schedule it power on/off and share it with your family to control together.
Factory Reset
Long press any button you desired to pair for about 5s until the Wi-Fi LED
indicator changes in a cycle of two short and one long flash and release, then
the reset is successful. The device enters quick pairing mode.
Please reset the switch to factory defaults if you want to use other Wi-Fi networks, then reconnect the network.
Common Problems
Q: Why my device stays “Offline”?
A: The newly added device needs 1 – 2mins to connect Wi-Fi and network. If it
stays offline for along time, please judge these problems by the blue Wi-Fi
indicator status:
-
The blue Wi-Fi indicator quickly flashes once per second, which means that the switch failed to connect your Wi-Fi:
1. Maybe you have entered a wrong Wi-Fi password.
2. Maybe there’s too much distance between the switch your router or the environment causes interference, consider getting close to the router. If failed, please add it again.
3. The 5G Wi-Fi network is not supported and only supports the 2.4GHz wireless network.
4. Maybe the MAC address filtering is open. Please turn it off.
If none of the above methods solved the problem, you can open the mobile datanetwork on your phone to create a Wi-Fi hotspot, then add the device again. -
Blue indicator quickly flashes twice per second, which means your device has connected to Wi-Fi but failed to connect to the server.
Ensure steady enough network. If double flash occurs frequently, which means you access an unsteady network, not a product problem. If thenetwork is normal, try to turn off the power to restart the switch.
Scatola | Scatola | Manuale | Borsa |
---|---|---|---|
PAP 20 | PAP 21 | PAP 22 | LDPE 4 |
Carta | Carta | Carta | Plastica |
RACCOLTA DIFFERENZIATA
SAR Warning
Under normal use of condition, this equipment should be kept a separation distance of at least 20 cm between the antenna and the body of the user.
EU Declaration of Conformity
Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio
equipment type TOUK1C/TOUK2C/TOUK3C/T1UK1C/T1UK2C/T1UK3C/T2UK1C/T2UK2C/T2UK3C/
T3UK1C/T3UK2C/T3UK3C is in compliance with Directive 2014/53/EU.The full text
of the EU declaration of conformity is available at the following internet
address: https://sonoff.tech/compliance/
WEEE Disposal and Recycling Information
All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.
For CE Frequency
EU Operating Frequency Range:
802.11 b/g/n20: 2412-2472MHz,
SRD: 433.92MHz (Receive Only for T1UK1C/T1UK2C/T1 UK3C/T2UK1
C/T2UK2C/T2UK3C/T3UK1C/T3UK2C/T3UK3C)
EU Output Power:
Wi-Fi 2.4Gs20dBm
Shenzhen Sonoff Technologies Co., Ltd.
1001, BLDG8, Lianhua Industrial Park, shenzhen, GD, China
ZIP code: 518000
Website: sonoff.tech
MADE IN CHINA
Documents / Resources
|
SONOFF TO-T1 Wi-Fi Smart Wall
Switch
[pdf] User Manual
TO-T1 Wi-Fi Smart Wall Switch, TO-T1, Wi-Fi Smart Wall Switch, Smart Wall
Switch, Wall Switch, Switch
---|---
|
SONOFF TO-T1 Wi-Fi Smart Wall
Switch
[pdf] User Manual
TO-T1, T2-T3, TO-T1 Wi-Fi Smart Wall Switch, Wi-Fi Smart Wall Switch, Smart
Wall Switch, Wall Switch
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>