ADDICTIVE DESERT DESIGNS F-150 Phantom Front Bumper Installation Guide

June 15, 2024
ADDICTIVE DESERT DESIGNS

INSTALLATION guide
22+/FORD RAPTOR
PHANTOM FRONT BUMPER
ADDICTIVE DESERT DESIGNS F 150 Phantom Front
Bumper

Preparation

We recommend reading through the installation instructions in whole before performing the work.

  • Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake.
  • When button head bolts are being used, install the supplied washer on the nut side. Then, hold the bolt stationary and only turn the nut to tighten. Do not turn the bolt to tighten hardware assembly, unless otherwise noted.
  • Anti-seize is recommended for all fasteners.

SKILL LEVEL
-Easy/Intermediate
This installation requires 2 people for best results
INCLUDED IN KIT
2- Nylon Lock Nuts (1/2-13”)
2- Button Head Bolts (1/2-13 X 1 1/2”)
2- Flat Washer (1/2”)
8- Nylon Lock Nuts (1/4-20”)
8- Button Head Bolts (1/4-20 X 1”)
8- Flat Washer (1/4”)
2- Hex Head Bolt (3/8-16 x 1 1/2”)
5- Nylon Lock Nuts (3/8-16”)
11- Flat Washers (3/8”)
4-Button head bolts (1 1/4”)
TIME REQUIRED
– 4 hours for OEM Removal/Bumper Install
-1 Additional Hour to Wire Cube Lights
Labor Rates are based on a vehicle with no pre-existing damage. Wiring labor is based on a standard wiring procedure with light switches installed in an easily accessible location. Custom light triggering or switch mounting location will result in a greater labor charge.
TOOLS REQUIRED
(Sockets) 7/16, 9/16, 3/4, 8mm, 10mm, 13mm, 15mm, 21mm ox end wrenches) 7/16, 9/16, 3/4, 8mm, 10mm, 13mm, 15mm, 21mm
(Allen wrenches) 5/32, 7/32, 5/16 Fastener remover or flathead screwdriver Zip ties Ratchet
PHANTOM FRONT BUMPER
22+/FORD RAPTOR
STEP 1

Removal

Remove the 6x bolts to release the OEM skid plate using a (13mm socket).

ADDICTIVE DESERT DESIGNS F 150 Phantom Front Bumper -
Removal

STEP 2
Remove the skid plate spacer.

ADDICTIVE DESERT DESIGNS F 150 Phantom Front Bumper - Removal
1

STEP 3
Remove the support brackets holding the bumper to the frame horns using a (8mm socket). (Repeat on other side)

ADDICTIVE DESERT DESIGNS F 150 Phantom Front Bumper - Removal
2

STEP 4
Unplug the main wiring harness plug in located on the passenger side by pulling the gray tab back as shown below.

ADDICTIVE DESERT DESIGNS F 150 Phantom Front Bumper - Removal
3

STEP 5
Remove the mounting bolts located on the frame horn using a (21mm Socket). (Repeat on other side)

ADDICTIVE DESERT DESIGNS F 150 Phantom Front Bumper - Removal
4

STEP 6
Remove the inter cooler guard bolts by using a (10mm socket) and remove the shutter motor from the guard. Zip tie the shutter motor to the wiring harness once it is installed on your ADD bumper.

ADDICTIVE DESERT DESIGNS F 150 Phantom Front Bumper -
BUMPER

STEP 7
Remove the tow hooks and the skid plate mount by using a (15mm socket) and a (13mm socket).

ADDICTIVE DESERT DESIGNS F 150 Phantom Front Bumper - BUMPER
1

STEP 8
Remove the OEM nut clips for the skid plate bottom mounts and replace with the provided 3/8” nut clips.

ADDICTIVE DESERT DESIGNS F 150 Phantom Front Bumper -
PHANTOM

STEP 9
Using a (10mm socket), remove the covers to expose the wire harness.

ADDICTIVE DESERT DESIGNS F 150 Phantom Front Bumper - PHANTOM
1

ADDICTIVE DESERT DESIGNS F 150 Phantom Front Bumper - PHANTOM
2

STEP 10
Remove all four parking sensors and bezels from the stock bumper and remove wire harness.

ADDICTIVE DESERT DESIGNS F 150 Phantom Front Bumper -
RAPTOR

INSTALLATION

STEP 11
Install the parking sensor mounts using the 1/4” button head bolts, washers, and nylon lock nuts using a (5/32 allen) and (7/16 wrench). (Repeat on other side)

ADDICTIVE DESERT DESIGNS F 150 Phantom Front Bumper -
NSTALLATION

STEP 12
Install the sensor bezels into the ADD bumper. If the bezels do not click into place you may have to trim the tabs to match the thickness of the bumper as shown below

ADDICTIVE DESERT DESIGNS F 150 Phantom Front Bumper - FORD
RAPTOR

STEP 13
Install the light mount brackets using the provided 1/4” button head bolts, washers, and nylon lock nuts using (5/32 allen wrench) and a (7/16 wrench). (Repeat on other side)

ADDICTIVE DESERT DESIGNS F 150 Phantom Front Bumper -
inside

STEP 14
Assemble the skid plate bottom mount to the skid plate using the provided 3/8” button head bolts, washers, nylon lock nuts with a (7/32 allen wrench) and (9/16 wrench).

ADDICTIVE DESERT DESIGNS F 150 Phantom Front Bumper -
bottom

ADDICTIVE DESERT DESIGNS F 150 Phantom Front Bumper - bottom
1

STEP 15
Install the skid plate to the bumper with the provided 3/8” button head bolts, washers, and nylon lock nuts using a (7/32 allen wrench) and (9/16 wrench).

ADDICTIVE DESERT DESIGNS F 150 Phantom Front Bumper -FRONT
BUMPER

STEP 16
Install the provided 3/8” nut clips in the slots on the bumper. (Repeat on other side)

ADDICTIVE DESERT DESIGNS F 150 Phantom Front Bumper -FRONT BUMPER
1

STEP 17
Install the wire harness with the plug in on the passenger side. Ensure parking sensors are in the orientation provide in the picture below

ADDICTIVE DESERT DESIGNS F 150 Phantom Front Bumper
-STEP

STEP 18
You can now install your Phantom front bumper with the provided 1/2” button head bolts, washers, and nylon lock nuts using a (5/16 allen wrench) and (3/4 wrench). Ensure the skid plate is installed underneath the rock guard as shown below

ADDICTIVE DESERT DESIGNS F 150 Phantom Front Bumper
-provided

STEP 19
Install the provided 3/8” hex head bolts, washers, and nylon lock nuts using a (9/16 socket).

ADDICTIVE DESERT DESIGNS F 150 Phantom Front Bumper
-ock

STEP 20
Plug in the wire harness. Ensure the clip is fully pushed down when plugged in as shown below

ADDICTIVE DESERT DESIGNS F 150 Phantom Front Bumper
-Ensure

Final

STEP 21
Stand back and enjoy your new ADD Phantom™ Front Bumper.
Check and re-tighten, if needed, all mounting bolts after 100 miles and periodically thereafter.

ADDICTIVE DESERT DESIGNS F 150 Phantom Front Bumper -Ensure
1

This product is protected by one or more U.S. patentswww.addictivedesertdesigns.com/patents
For Additional Support or Technical Questions,

Please Call480-671-0820 or
EmailInfo@AddictiveDesertDesigns.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

ADDICTIVE DESERT DESIGNS User Manuals

Related Manuals