Addictive Desert Designs F260014120103 Bomber Front Bumper Installation Guide

June 13, 2024
ADDICTIVE DESERT DESIGNS

Addictive Desert Designs F260014120103 Bomber Front Bumper

Addictive-Desert-Designs-F260014120103-Bomber-Front-Bumper-
product

Product Information

The Addictive Desert Designs Bomber Front Bumper is designed for the 23+ Ford Bronco Raptor. It is a durable and stylish bumper that enhances the look and functionality of your vehicle. The bumper is available in two options: Baja Option and Rigid Option.

Preparation

We recommend reading through the installation instructions in whole before performing the work.

  • Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake.
  • When button head bolts are being used, install the supplied washer on the nut side. Then, hold the bolt stationary and only turn the nut to tighten. Do not turn the bolt to tighten hardware assembly, unless otherwise noted.
  • Anti-seize is recommended for all fasteners.

SKILL LEVEL

  • Easy/Intermediate
    This installation requires 2 people for best results

INCLUDED IN KIT

  • Hex Head Bolt (3/8-16 x 1 1/4”)
  • Fender Washers (3/8”)
  • Sensor Plugs

TIME REQUIRED

  • hours for OEM Removal/Bumper Install
  • Additional Hour to Wire Cube Lights/Winch
    Labor Rates are based on a vehicle with no pre-existing damage. Wiring labor is based on a standard wiring procedure with light switches installed in an easily accessible location. Custom light triggering or switch mounting location will result in a greater labor charge.

TOOLS REQUIRED

(Sockets) 9/16, 10mm, 15mm (Box end wrenches) 9/16, 10mm, 15mm (Torx) T30, T40
Fastener remover or flathead screwdriver Zip ties Ratchet

INSTALLATION guide

Baja Option

Addictive-Desert-Designs-F260014120103-Bomber-Front-
Bumper-01

Rigid Option

Addictive-Desert-Designs-F260014120103-Bomber-Front-
Bumper-02

STEP 1Addictive-Desert-Designs-F260014120103-Bomber-Front-
Bumper-03
Disconnect the wire harness plug located on the driver side.

STEP 2Addictive-Desert-Designs-F260014120103-Bomber-Front-
Bumper-04
Remove the skid plate using a (15mm socket). *Keep these for they will be used later on in the install

STEP 3Addictive-Desert-Designs-F260014120103-Bomber-Front-
Bumper-05
Remove all the push pins for the front cover using a (fastener remover/flathead).

STEP 4Addictive-Desert-Designs-F260014120103-Bomber-Front-
Bumper-06
Remove the mounting bolts located on the tow hooks using a (15mm socket). You can now remove the bumper

STEP 5

Addictive-Desert-Designs-F260014120103-Bomber-Front-
Bumper-07
Follow the ACC install guide before continuing with the install.
https://cdn.shopify.com/s/files/1/0627/4508/4140/files/2021-ford-bronco- cruise-control-install

STEP 6

Addictive-Desert-Designs-F260014120103-Bomber-Front-
Bumper-09
Remove the mounting bracket plastic nuts located behind the frame horns. There are 2x on each side.

STEP 7 Addictive-Desert-Designs-F260014120103-Bomber-Front-
Bumper-010Remove the plastic covers on each outer sides using a (fastener remover/flathead).

STEP 8Addictive-Desert-Designs-F260014120103-Bomber-Front-
Bumper-011
Next, Remove the 4x bolts holding the light brackets using a (T30). Then disconnect the plug located above the lights
STEP 9Addictive-Desert-Designs-F260014120103-Bomber-Front-
Bumper-012
Remove the tow hook brackets using a (10mm socket).

STEP 10Addictive-Desert-Designs-F260014120103-Bomber-Front-
Bumper-013
Remove the 5x bolts holding the middle plate using a (T40).
STEP 11Addictive-Desert-Designs-F260014120103-Bomber-Front-
Bumper-014
Remove all of the front and top face bolts that are indicated below using a (T40).

STEP 12Addictive-Desert-Designs-F260014120103-Bomber-Front-
Bumper-015
You can now remove the wire harness by removing the sensors and sensor bezels by follow the images below. Remember the orientation for this will be important in step 13

STEP 13Addictive-Desert-Designs-F260014120103-Bomber-Front-
Bumper-016
Install the sensor bezels into the ADD bumper. Ensure they are in the same orientation as OEM. If the bezels do not click into place you may have to trim the tabs to match the thickness of the bumper as shown below

STEP 14Addictive-Desert-Designs-F260014120103-Bomber-Front-
Bumper-017
Install the U-nut clips in the provided mounting slots.

STEP 15Addictive-Desert-Designs-F260014120103-Bomber-Front-
Bumper-018
Install the wiring harness along the top of the bumper. Unplug the outer sensors to pass through the back side of the mounting plate.

STEP 16Addictive-Desert-Designs-F260014120103-Bomber-Front-
Bumper-021

You can now install the bumper with the 6x provided 3/8” hex head bolts, and washers using a (9/16 socket/wrench

STEP 17Addictive-Desert-Designs-F260014120103-Bomber-Front-
Bumper-020
Install the skid plate using the same mounting holes with the same OEM hardware using a (15mm socket).

STEP 1Addictive-Desert-Designs-F260014120103-Bomber-Front-
Bumper-021
Stand back and enjoy your new ADD Bomber™ Front Bumper. Check and re-tighten, if needed, all mounting bolts after 100 miles and periodically thereafter.

This product is protected by one or more U.S. patents www.addictivedesertdesigns.com/patents

For Additional Support or Technical Questions, Please Call 480-671-0820 or Email Info@AddictiveDesertDesigns.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

ADDICTIVE DESERT DESIGNS User Manuals

Related Manuals