ADDICTIVE DESERT DESIGNS 22+/FORD F-150 Pro Bolt On Rear Bumper Installation Guide

June 13, 2024
ADDICTIVE DESERT DESIGNS

INSTALLATION guide
22+/FORD F-150
PRO-BOLT ON REAR BUMPERADDICTIVE DESERT DESIGNS 22+ FORD F-150 Pro Bolt
On Rear Bumper

Preparation

We recommend reading through the installation instructions in whole before performing the work.

  • Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake.
  • When button head bolts are being used, install the supplied washer on the nut side. Then, hold the bolt stationary and only turn the nut to tighten. Do not turn the bolt to tighten hardware assembly, unless otherwise noted.
  • Anti-seize is recommended for all fasteners.

SKILL LEVEL
-Easy/Intermediate
This installation requires 2 people for best results
INCLUDED IN KIT
4- Hex Head Bolts (3/8-16 x 1”)
2- Button Head Bolts (3/8-16 x 1”)
6- Nylon Lock Nuts (3/8-16”)
12- Flat Washers (3/8”)
2- Sensor Plugs
2- Snap In Nut (1/4”)
2- Sheet Metal Screws (1/4”)
TIME REQUIRED
– 2.5 hours for OEM Removal/Bumper Install
-1 Additional Hour to Wire Cube Lights
Labor Rates are based on a vehicle with no pre-existing damage. Wiring labor is based on a standard wiring procedure with light switches installed in an easily accessible location. Custom light triggering or switch mounting location will result in a greater labor charge.
TOOLS REQUIRED
(Sockets) 9/16, 10mm, 13mm
(Box end wrenches) 9/16, 10mm, 13mm
(Allen wrenches) 7/32
Fastener remover or flathead screwdriver
Zip ties
Ratchet
Grinder

Removal

STEP 1
Unplug the main wire harness located on the passenger side by pulling the gray tab back as shown below. Remove the ground using a (10mm socket) located on the passenger side on the frame rail.

ADDICTIVE DESERT DESIGNS 22+ FORD F-150 Pro Bolt On Rear Bumper -
Fig1

STEP 2
Unplug/remove the trailer plug.

ADDICTIVE DESERT DESIGNS 22+ FORD F-150 Pro Bolt On Rear Bumper -
Fig2

STEP 3
Remove the license plate light by twisting counter clock wise and remove the housing.

ADDICTIVE DESERT DESIGNS 22+ FORD F-150 Pro Bolt On Rear Bumper -
Fig3

STEP 4
Remove the parking sensors and bezels from the stock bumper, You can now remove the wire harness and set aside for install. Remember the location and orientation of the sensor bezels after removal for this will be important later on in the install

ADDICTIVE DESERT DESIGNS 22+ FORD F-150 Pro Bolt On Rear Bumper -
Fig4

STEP 5
Pull the top plastic cover off the bumper. There are no tools required for this step, it simply pulls off by hand.

ADDICTIVE DESERT DESIGNS 22+ FORD F-150 Pro Bolt On Rear Bumper -
Fig5 STEP 6
Using a (13mm Socket), remove the mounting bolts that hold the bumper side covers to the vehicle.

ADDICTIVE DESERT DESIGNS 22+ FORD F-150 Pro Bolt On Rear Bumper -
Fig6 STEP 7
Remove the license plate bracket by using a (grinder) to grinding through the five visible welds that connect that bracket to the hitch. Once the bracket has been removed, paint over the raw metal to prevent rust

ADDICTIVE DESERT DESIGNS 22+ FORD F-150 Pro Bolt On Rear Bumper -
Fig7

INSTALLATION

STEP 8
Install the license plate light housing. Be sure that the clips are fully clipped in by using a (flathead) to pry into place. DO NOT pry to hard due to breakage

ADDICTIVE DESERT DESIGNS 22+ FORD F-150 Pro Bolt On Rear Bumper -
Fig8 STEP 9
Install the sensor bezels in the correct orientation they were removed from the stock rear bumper. The plug ins will face towards the inside of the bumper on both sides as shown on page 10.

ADDICTIVE DESERT DESIGNS 22+ FORD F-150 Pro Bolt On Rear Bumper -
Fig9ADDICTIVE DESERT
DESIGNS 22+ FORD F-150 Pro Bolt On Rear Bumper - Fig10 STEP 10
If your sensor bezels do not click into place, you may have to trim the mounting tabs to accommodate for the thickness of the material on your new bumper.

ADDICTIVE DESERT DESIGNS 22+ FORD F-150 Pro Bolt On Rear Bumper -
Fig11

STEP 11
Some F-150 packages come with six parking sensor. If you have four use the provided plugs to plug the two outer sensor holes on each side.

ADDICTIVE DESERT DESIGNS 22+ FORD F-150 Pro Bolt On Rear Bumper -
Fig12 STEP 12
Install the trailer plug and pry out the tabs to securely seat plug using a (flathead screwdriver).

ADDICTIVE DESERT DESIGNS 22+ FORD F-150 Pro Bolt On Rear Bumper -
Fig13 STEP 13
You can now install your Pro-Bolt On™ rear bumper with the provided 3/8” button head bolts, washers, and nylon lock nuts using a (7/32 allen) and (9/16 socket). Install the provided 3/8” hex head bolts, washers, and nylon lock nuts using a (9/16 socket) and (9/16 wrench).ADDICTIVE DESERT DESIGNS 22+
FORD F-150 Pro Bolt On Rear Bumper - Fig14 STEP 14
Plug in the wire harness, and reinstall the ground using a (10mm). Ensure the clip is fully pushed down when plugged in as shown below

ADDICTIVE DESERT DESIGNS 22+ FORD F-150 Pro Bolt On Rear Bumper -
Fig15

FINAL

STEP 15
Stand back and enjoy your new ADD Pro- Bolt On™ rear bumper.
Check and re-tighten, if needed, all mounting bolts after 100 miles and periodically thereafter.

ADDICTIVE DESERT DESIGNS 22+ FORD F-150 Pro Bolt On Rear Bumper -
Fig16

This product is protected by one or more U.S. patents
www.addictivedesertdesigns.com/patents
Page 15 | Addictive Desert Designs
For Additional Support or Technical Questions,
Please Call 480-671-0820 or
Email Info@AddictiveDesertDesigns.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

ADDICTIVE DESERT DESIGNS User Manuals

Related Manuals