tuya PE523W Multifunction Smart Wi-Fi Alarm Siren User Manual

tuya PE523W Multifunction Smart Wi-Fi Alarm Siren

Product Information

The WiFi Wireless Strobe Alarm Siren is a versatile and powerful security device that helps protect your home or office. It features a built-in speaker, PIR sensor, LED indicator, mounting bracket, external power connector, spare battery, on/off setting button, function jumper position, and buzzer. With its wireless capabilities and various settings, this alarm siren provides reliable and customizable security options.

Specifications:

• External power voltage: DC5V/1A
• Operation current: 50mA (Mark1), 60mA (Mark2)
• Alarm current: 200mA (Mark3), 300mA (Mark4)
• Alarm voltage: 80db@3m
• Wireless receiving range: 100m
• Wireless frequency code: 433MHZ
• Encoding method: EV1527/2262
• Wi-Fi method: IEEE802.11b/g/n
• Spare battery: 3.7V 1000mA
• Applicable temperature: -20°C to 55°C
• Applicable humidity: 40% to 80%RH
• Outstanding size: 164.3124.359mm

Product Usage Instructions

Mounting and Setup:

1. Open the gift box and ensure all the components are included (device, battery, mounting bracket, etc.).
2. Choose a suitable location for mounting the siren and use the provided mounting bracket and bag to securely attach it.
3. Connect the external power connector to the siren and plug it into a power source (DC5V/1A).
4. If desired, insert the spare battery into the siren for backup power.
5. Adjust the function jumper position according to your desired settings (refer to the function jump cap selection section in the manual).
6. The siren is now ready for use.

Deleting Remote Controllers and Sensors:
To delete all remote controllers and sensors connected to the siren:

1. Power on the siren.
2. Press and hold the setting key until the siren rings 4 times and the indicator flashes.
3. Release the setting key. The voice broadcast system will initialize and the siren will emit a 2 times prompt.
4. The deletion process is complete.

PIR Mode Setting:
To set the PIR mode of the siren:

1. Power on the siren.
2. Press and hold the set key until the siren rings 5 times and the indicator flashes.
3. Release the set key. The voice broadcast will indicate that the infrared setting mode is active.
4. Click the set key to close or open the infrared. The light will flash accordingly, and the voice broadcast will confirm the status.
5. If there is no operation within 5 seconds, the siren will automatically exit the setting mode.

Deleting Wi-Fi:
To delete the Wi-Fi network from the siren:

1. Power on the siren.
2. Press and hold the setting key until the siren rings 6 times.
3. Release the setting key. The buzzer will make a sound and the indicator will flash once, indicating the Wi-Fi clearance.
4. The voice broadcast will confirm that the siren has entered the Wi-Fi distribution network mode.
5. If the siren receives a distribution network signal within 120 seconds, it will broadcast the Wi-Fi distribution network failure voice and exit the clear Wi-Fi mode.

Device Networking:

1. Download the Smart Life app from your preferred app store or scan the provided QR code to download.
2. The Smart Life app is available in major app stores worldwide.
3. Launch the app and follow the on-screen instructions to set up and connect the siren to your Wi-Fi network.

FAQ

• Q: What is the wireless frequency code used by the siren?
  The wireless frequency code used by the siren is 433MHZ.

• Q: Can I use the siren without connecting it to a power source?
  No, the siren requires an external power source (DC5V/1A) for operation. However, it also has a spare battery for backup power.

• Q: What is the wireless receiving range of the siren?
  The wireless receiving range of the siren is 100 meters.

Warning

• Please read the instructions carefully before using this product.
• The protection grade of this product is IP65, should avoid the alarm immersion in water, and avoid the alarm falling, do not knock, open or change the alarm, otherwise the alarm may lead to product failure.

Product Overview

Wi-Fi wireless acoustic and visual alarm with alarm and accessories integration design, when the system belongs to any detector found alarm, alarm will immediately issued high decibel siren, at the same time, like a police car, overhead light flashing warning light, and alarm signal through the networking module, the alarm information send mobile phone APP, let the user receive alarm and processing in a timely manner. The signal between alarm number and detector is wireless transmitted for easy installation; the remote control is more convenient and quick; the remote control has emergency alarm button and press will alarm immediately.

Factory list

1. Gift-box 1pcs
2. device 1set
3. battery 1pcs
4. Mounting bracket 1pcs
5. Mounting bag 1pcs
6. User manual 1pcs

Function

SPECIFICATION

1. Average current value of backup battery power supply
2. Average current value of DC 5V power
3. Average current value of the spare battery alarming
4. Average current value of the DC 5V power alarming

Function jump cap selection

• Alarm sound optional: JP2 &JP3 no jumper，alarm voice should be 110(picture1).
  • JP2 with jumper, alarm voice should be 119(picture2).
  • JP with jumper,alarm voice should be 120(picture3).
• Alarm sound time optional：JP1 without jumper alarm sound should be 5 minutes（picture1). JP1 (1Pin&2Pin）with jumper, alarm sound should be 1 minutes(picture 2). JP1 2Pin&3Pin) with jumper, alarm sound should be 3 minutes（picture 3).
• PIR on/off: JP5 with jumper, PIR mode open (picture1).
  • JP5 without jumper，PIR mode closed（picture 2).
• Strobe mode optional：JP4 with jumper，strobe and sound alarm（picture1).
  • JP4 without jumper，strobe only without sound（picture 2).
    remark: All function switching needs to be power off and power on before switching successfully.

Function setting and testing

1. enter the wifi networking mode
   press the setting button until the voice “enter the Wi-Fi distribution configure mode”, release the setting button, the built-in buzzer of the alarm will ring 1 and accompany the indicator light flashing 2 times, and then the indicator light shows that when the Wi-Fi distribution configure is successful, the voice prompt “Wi-Fi” distribution configure is successful. When the Wi-Fi distribution configure fails, the voice prompt “Wi-Fi distribution configure fails”.

2. external 2 channel wired zones

3. CN1 1 channel wired zone, connect Z0 with GND.

4. CN1 1 channel wired zone connect Z1 with GND.
   Z1| Z0| GND| POWER
   ---|---|---|---

5. remote controller pairing
   After boot, press the setting key of the sound and light alarm number until the sound, with the indicator light flashing. After the voice broadcast “remote control learning, please press the alarm button”, release the setting button to trigger a remote control code, the alarm number will issue a 2 sound prompt, and the voice broadcast “learning success” indicates the success of learning. If you want to continue learning the next remote control, you just need to trigger the remote control again. If the sound and light alarm number can not receive any wireless signal, after 5s, automatically exit. Support learning up to 5 remote controls, more than 5 remote controls, will cycle to cover the earliest learning remote control, retain the latest learning of 5 remote controls.

6. wireless sensor pairing
   After boot, press the setting key of the siren until it rings 2 times, and the indicator light flashes. After the voice broadcast “accessories learning, please trigger the accessories”, release the setting button to trigger a detector code, the alarm number will sound 2 times, and the voice broadcast “learning success” indicates the success of learning. If you want to continue learning about the next detector, you just need to trigger the detector again. If the sound and light alarm number can not receive any wireless signal, after 5s, automatically exit. Support learning up to 20 detectors, more than 20 detectors, which will cycle to cover the earliest learned detectors and keep the latest learned 5 detectors.

7. Setting for used as a strobe siren
   At this time, the device is equivalent to a wireless external alarm sirem, as long as the host has an alarm situation, the sound and light warning will issue a sound and light alarm. After boot, press the setting key of sound and light alarm, until ring 3, and with the light flashing, voice broadcast “host learning, please trigger host”, open the setting button, let the alarm host launch a wireless coding signal, sound and light alarm after receiving the signal 2 sound prompt, voice broadcast “learning success” said learning success. Maximum support for learning a host.

8. delete all the remote controller and sensors
   After boot, press the setting key of siren until it rings 4 times, accompanied by the indicator flash, the voice broadcast “system initialization, please release the setting key later”, the independent alarm emits a 2 times prompt, and the voice broadcast “initialization”, indicating the success of deletion.

9. PIR mode setting
   After boot, press the set key of siren until rings 5 times, accompanied by the indicator flash, voice broadcast “into the infrared setting mode” loosen the set key, at this point, the light flashing, click a set key, close infrared, voice broadcast “infrared close”, click again set key, open infrared, voice broadcast “infrared open”, 5 seconds within no operation, automatically exit.

10. Delete Wi-Fi
    After startup, press the setting key of the siren until it rings 6 times, release the setting key, the buzzer drops sound, with the indicator flashing once, on behalf of the Wi-Fi clearance, the voice broadcast “enter the Wi-Fi distribution network mode” flash, the distribution network state, received the distribution network signal within 120 seconds, broadcast the “Wi-Fi distribution network failure” voice, and exit the clear Wi-Fi.

11. Strobe siren State

    • Arm state: When the alarm is in this state, all accessories can trigger the siren alarm Disarm state: When the alarm is in this state, only the accessories in the emergency defense area can trigger the siren alarm, and other accessories can not trigger the siren alarm.
    • Alarm state: when the alarm is in this state, the field sound and light alarm begins, and in the absence of human operation, the alarm automatically exits the alarm state after the alarm time and returns to the alarm state.

12. Daily operation
    Remote controller is a kind of equipment that operates sound and light alarm by radio. The function is convenient for users in the door (door) or long distance, the sound and light alarm out Alarm, home protection, emergency arm, immediate evacuation and other functional operation

    • Out arm: press［ ］key，the siren is in the arm state.
    • Disarm: press［ ］key，the siren is in the disarm state.
    • Home Arm: press［ ］key，the siren is the home arm state.
    • SOS alarm: press［SOS］button，the siren will be triggered.

Device networking

1. APP download
   The smart Life APP has been released. In major app stores around the world, you can search for “Smart Life” in the app store and scan the QR code below to download. Please scan the QR code of the Google Play link to download. The smart life APP downloaded by Google Play is the same APP, but the download channel is different.

2. When registering and login with the mobile phone number, it is necessary to replace the ” xx” country code at the beginning of the mobile phone number account with the corresponding code of the mobile phone number host country in the corresponding country / region during the registration and login.

3. Device networking

4. default the network is the one key networking, for networking, mobile should connect the same wifi as the device, (can only support 2.4GHz wifi).

5. APP adding step

6. long press the setting key till get the voice “ get into the wifi networking mode” loose the setting key, the built-in buzzer will sound. 1 times and flashing 2 times, means the device getting into networking mode.

7. open the mobile APP, choose the “adding”.

8. Sensors → Alarm（wifi）

9. Enter WiFi password→Next

10. Confirm the indicator is blinking

11. Blink Quickly

Installation instructions

Install the bracket for the right place by using the expanding screw (hoop up towards) then put the siren at the bracket buckle down to the top.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>