PROGRESS LIGHTING P300405-31M-CS 16 Inch Linear Vanity Instruction Manual
- June 15, 2024
- PROGRESS LIGHTING
Table of Contents
PROGRESS LIGHTING P300405-31M-CS 16 Inch Linear Vanity
PACKAGE CONTENTS
HARDWARE CONTENTS
(not actual size)
Safety Information
- Please read and understand this entire manual before attempting to assemble, operate, or install the product.
- CAUTION: Read instructions carefully and turn the electricity off at the main circuit breaker panel before beginning installation.
- CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified electrician to ensure the correct branch circuit conductor.
- WARNING: If any Special Control Devices are used with this fixture, follow instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, contact a qualified electrical contractor.
- CAUTION: All glass is fragile. Use care when handling glass shades and bulbs.
- THIS PRODUCT MUST BE INSTALLED BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED, UNDER THE APPLICABLE INSTALLATION CODE.
- KEEP THESE INSTALLATION INSTRUCTIONS
Preparation
- Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install, or operate the product.
- Estimated assembly time: 30 minutes.
- Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.
Care and Maintenance
- Shut off the main power supply before cleaning the product or changing light bulbs. To clean, wipe with a damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.
Assembly Instructions
- The back plate (AA) comes assembled inside the canopy. First, detach the backplate from the canopy by removing the screws (CC). Make sure to save the screws for step 3.
- Then attach the back plate to the outlet box using the mounting screws supplied with the outlet box (not included).
- Strip 3/8″ of insulation from the electrical wire ends. Using wire nuts (BB), connect the white fixture wire to the white supply wire from the outlet box; connect the fixture black wire to the black supply wire.
- Connect the fixture ground wire and supply ground wire using a wire nut or by fastening it to the ground screw on the back plate. Push all wire connections into the outlet box.
- Attach fixture (A) to the back plate (AA) using a flat head screw (CC) to secure tightly.
- Use the CCT switch to select either 3000K, 4000K, or 5000K settings.
FCC
This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Assembly and Installation Instructions
CAUTION: Read the instructions carefully and turn off the power at the
central circuit breaker before starting the installation.
CAUTION: Read instructions carefully and turn off the power at the
central circuit breaker before beginning installation.
WARNING: Fire hazard. Min 90°C power conductors. Consult a qualified
electrician to ensure a proper good branch circuit conductor.
WARNING – If there are other regulating mechanisms used with this device,
carefully follow instructions to meet NEC requirements. If you have any
questions, consult a qualified electrician.
CAUTION – Glass is always fragile; Handle the component(s) and/or bulb(s)
with care.
THIS PRODUCT MUST BE INSTALLED ACCORDING TO THE RELEVANT INSTALLATION CODE, BY
A PERSON WHO KNOWS THE PRODUCT AND ITS OPERATION WELL AS WELL AS THE INHERENT
RISKS. SAVE THESE INSTALLATION INSTRUCTIONS
- THANK YOU for selecting Progress Lighting
- We can assist you with questions regarding product information, assembly, or missing parts
- 800-447-0573
- customerservice@progresslighting.com
- 8 am-8 pm (Eastern), Monday-Friday
- For warranty information, please refer to https://www.hubbell.com/progresslighting/en/warranty
Documents / Resources
|
PROGRESS LIGHTING P300405-31M-CS 16 Inch Linear
Vanity
[pdf] Instruction Manual
P300405-31M-CS 16 Inch Linear Vanity, P300405-31M-CS, 16 Inch Linear Vanity,
Linear Vanity, Vanity
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>