PRO MOUNTS PPMA2S-E Dual Monitor Arm Instruction Manual

PRO MOUNTS PPMA2S-E Dual Monitor Arm Instruction Manual

IMPORTANT SAFETY INFORMATION

Please carefully read all instructions before attempting installation.
CAUTION: Avoid potential personal injuries and property damage!

• Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We are not liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
• This product contains a high pressure gas spring, fire and percussion prohibited. Also it is strictly prohibited to dismantle without professionals. Please return to the manufacturer or hand over to professional agencies if the product is abandoned.
• The desk must be capable of supporting three times the weight of the total load (the mount, the monitor and all accessories weight). Don’t use the product on particle board.

Weight Restrictions

If your monitor weighs more, this mount is NOT compatible.

WARNING
DO NOT exceed the maximum weight indicated. This mounting system is intended for use only within the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in failure of the mount and its accessories, causing possible damage and or injury.

**Check the VESA Pattern of Your Monitor before You Begin the Installation

**

Minimum VESA pattern : 75mm/3 in.(W)x75mm/3 in. (H)

If your monitor VESA is greater than 100×100 mm/4×4 in. or less than VESA 75x75mm/3x3in., this mount is NOT compatible.

Product Features

**TENSION ADJUSTMENT SHOULD BE DONE ONLY AFTER MOUNT INSTALLATION

**

Do not adjust tension without monitor.

1. Ensure monitor has been attached to the mount.
2. Read your monitor box or manual to find out monitor net weight.
3. Ensure the net weight of monitor (including accessories) is within 17.6 lbs (8 kg

Clockwise to reduce tension(carry less weight Counter-clockwise to increase tension(carry more weight)

Warning!

Tools Needed (Not Included)

• Drill

• Wood Drill 10-20mm (0.4 in.-0.8 in.)

Supplied Parts and Hardware

Warning: This product contains small items that could be a choking hazard if undamaged. Do not use swallowed.

Before starting assembly, verify all parts are included and hardware included in this damaged or defective parts.

• Please note: Not all package will be used.

Supplied Parts and Hardware for Step 1

• Pole Assembly 01 (x1)

• Base 02 (x1

• C-Clamp Brace 03 (x1)

• 04 (x1)

• Foot Pad 05 (x4)

• Knob 06 (x1)

• Cable Cover 07 (x1)

• Bottom Plate 08 (x1)

• Grommet Bolt 09 (x1)

• Locking Plate 10 (x1)

• Cable Clip 11 (x1)

• Bolt M6x10mm A (x2)

• Bolt M6x12mm B (x3)

• Bolt M6x20mm C (x3

• 5/32 in.(4mm) Small Allen Key D (x1)

Supplied Parts and Hardware for Step 2

• Arm Assembly 12 (x1)

• 15/64 in.(6mm) Large Allen Key E (x1)

Supplied Parts and Hardware for Step 3

• Bolt M4x12mm M-A (x8

• Bolt M4x30mm M-B (x8

• D4 Washer M-C (x8)

• 13mm Spacer M-D (x8)

• Faceplate 13 (x2)

• Bolt F (x2)

Supplied Hardware for Step 4

Supplied Hardware for Step 5

• 15/64 in.(6mm) Large Allen Key E (x1)

• 13/64 in.(5mm) Medium Allen Key G (x1)

Supplied Part for Step 6

• Cable Cover 14 (x2

Install the Base

**A. For Clamp Mounting

Warning:** 02 Small Allen Key Ensure bolts are secured firmly.

Warning: Ensure bolts are secured firmly.

**B. For Grommet Mounting

**

If there is no grommet hole on your desk, position the base [02] on the mounting surface and mark the hole. Drill a hole using the drill bit in a diameter of 0.4-0.Bin. (10-20mm) at the marked position through the mounting surface.

Install the Arm

Warning:
Ensure pre-assembled set screw is secured firmly.

Attach Monitor to the Arm

Adjust Gas Spring Tension

Be sure to keep the arm in horizontal position during adjustment. Or else, it would be difficult to adjust the mount or damage the mount.

1. If the monitor can stay at the desired height by itself, no adjustment needed.
2. If the monitor rises up, press the arm to keep it in horizontal position and then use the Large Allen Key (E) to turn the bolt clockwise(“-” direction) to reduce tension of the arm only until the monitor can stay at the desired height by itself.
3. If the monitor falls down, lift the arm to keep it in horizontal position and then use the Large Allen Key (E) to turn the bolt counter-clockwise(“+” direction) to increase tension of the arm only until the monitor can stay at the desired height by itself.

Rotation Adjustment

360° Rotation

For horizontal and vertical mounting options

Route Cables along the Arms

After managing the cables along the arm, pinch the both sides of the top end of the cable cover [14] to make it attach to the arm.

ProMounts USA,
17882 Hamilton Ave,
Torrance, CA 90502
Tel: 310-645-6400

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>