BG ELECTRICAL 822UAC30-01 Nexus Metal USB Charging Sockets Instruction Manual
- June 11, 2024
- BG Electrical
Table of Contents
BG ELECTRICAL 822UAC30-01 Nexus Metal USB Charging Sockets
Wiring Instructions
Power Off
Before commencing work always isolate the power at the consumer unit / fuse
box.
*Note – If your installation uses a four-lug metal mounting box, remove the top and bottom lugs or bend fully back.
Replacing an existing accessory
-
Unscrew the accessory from the wall/mounting box.
-
Note the cable connections:
The illustration shows 1 wire of each colour connected to each terminal.
There should be an additional connection between the mounting box earth terminal and the accessory earth terminal. -
Unscrew each terminal to release the wire.
New installation
-
Install mounting box (metal or moulded) for either flush or surface mounting, ensuring appropriate size of product (Mounting box to be purchased separately).
-
Select the most suitable entry point of the mounting box (knock-out) and route the cables through.
If a metal box is used, a cable grommet should be fitted to the entry point. -
Cables should be prepared so a sufficient conductor length reaches the terminals.
Strip the ends of the individual conductors leaving an adequate length bare to enter terminals
Connection (See diagram)
-
Line up the new accessory to mounting box and take note of where each terminal is located.
-
Connect each wire to the matching terminal.
An earth connection should always be made between the mounting box earth terminal and the accessory earth terminal, where fitted.
All bare earth wires must be sheathed with green/yellow sleeving.
When connecting the new accessory ensure that only the bare end of the wire enters the terminal and no bare wires are visible. -
Tighten terminal screws securely. (Do not over tighten)
-
This socket is fitted with two linked terminals to provide a dual earth facility. This is for use in “clean” installations where additional earth capacity is required to comply with Regulation 607 IEE Wiring Regulations.
Complete Installation & Test
- Carefully position the accessory into the mounting box, ensuring that no wires are trapped between the plate and the wall and secure with screws (do not over tighten) then insert screw covers (optional).
- Once the installation has been completed correctly, replace the fuse/ reset MCB (trip), switch the power back on at the consumer unit and test
Insulation Testing
This socket outlet is designed to withstand insulation resistance testing at 500V as defined by BS1363-2.
- Perform insulation test between Line & Neutral at 250V
- 500V test may be performed between Line & Earth, Neutral & Earth. Or,
- Disconnect all Neutral connection in the socket and connect into terminal block before replacing the socket prior to test.
Safety Warning
For your safety, this product must be installed in accordance with local
Building Regulations. If in any doubt, or where required by the law, consult
a competent person who is registered with an electrical self-certification
scheme. Further information is available online or from your Local
Authority.
Please read carefully and use in accordance with these safety wiring
instructions. Before commencing any electrical work ensure the supply is
switched off at the mains. Either by switching off the consumer unit or by
removing the appropriate fuse or turning off MCB (trip). Wiring should be in
accordance with the latest edition of the IET regulations (BS 7671).
To prevent fire hazard always use cable of the correct rating & type for the
application.
Warning do not exceed the load rating of this device as stated on the
rear of the product.
Wire Identification – Twin & Earth Cable
Note – As from 1st April 2004 new colour codes for hard wire
installations
were introduced.
EARTH = Green/Yellow Sleeving
NEUTRAL = Black (pre Apr 04) / Blue (after Apr 04)
LIVE = Red (pre Apr 04) / Brown (after Apr 04)
1 Gang 13 Amp Switched Socket with USB Charger
USB charge shared between outputs
2 Gang 13 Amp Switched Socket with USB Charger
USB charge shared between outputs
2 Gang 13 Amp Unstitched Socket with USB Charger
4.2A USB charge shared between outputs.
Each pair of USB outlets provides a 2.1A charge, shared between both outputs.
Additional Advice for Decorative Products
Fixing method varies depending on which product range is supplied. Always
ensure wall surface is reasonably flat and smooth, with no bumps or
projections. Metal front plates WITH screw fixing holes, fix the unit to the
back box using two fixing screws supplied. All Decorative products MUST have
an earth connection between the front plate and back box. Front plates WITHOUT
screw fixing holes. These products comprise main unit with integral gasket,
and front plate as separate item. Fix unit to back box using two fixing screws
supplied. Clip front plate onto main assembly, ensuring screwdriver notch is
located bottom right hand corner.
To remove plate, place medium size flat bladed screwdriver in notch and lever
off against gasket.
USB Charger Information
13A sockets with USB charging ports for charging mobile devices such as mobile
phones, MP3 players and tablets.
Total charger current can be delivered from one USB socket or divided between
outputs as required.
For a 2.1A output charger, if a device needing 1.5A would leave the other port
at 0.6A, so devices may charge more slowly than with a normal single plug
charging.
The speed of charging will depend on the battery capacity of the device and
not charge output of the socket. A device with a battery capacity of 1500mAh
will not charge any faster with a 3.1A charger compared to a 2.1A charger.
The total output current achieved is dictated by the specific device being
charged and other external factors, such as the quality of charging cable
being used.
Overload protection for connected devices.
Low energy stand-by mode
When not in use the USB sockets are in a low energy stand-by mode.
The usb circuits in this socket are designed to withstand insulation
resistance tests at 500V. A reading of 10MΩ minimum is typically achieved by
the USB socket
USB Output| 5.0V DC 2.1A, 10.5W MAX| 5.0V DC 3.1A, 15.5W MAX| Type
A:
5.0V DC 2.4A,
12.0W MAX Type C:
5.0V DC 3.0A,
15.0W MAX| Type C:
5.0V DC, 3.0A 15.0W MAX
9.0V DC, 3.0A 27.0W MAX
12.0V DC, 2.5A 30.0W MAX
15.0V DC, 2.0A 30.0W MAX
20.0V DC, 1.5A 30.0W MAX
Type A:
5.0V DC 3.0A 15.0W MAX
9.0V DC 3.0A 27.0W MAX
12.0V DC 2.25A 27.0W MAX
---|---|---|---|---
Input| 220-250V~ 50/60Hz| 220-250V~ 50/60Hz| 200-250V~ 50/60Hz|
220-250V~ 50/60Hz
Average active efficiency| >79.04%| >81.59%| Type A:
5.0V DC 2.4A:
79.94%
5.0V DC 3.0A:
81.39%
Total:4.2A
83.35%| Type C:
5.0V DC, 3.0A: >81.39%
9.0V DC, 3.0A: >86.62%
12.0V DC, 2.5A: >86.95%
15.0V DC, 2.0A: >86.95%
20.0V DC, 1.5A: >86.95%
Type A:
5.0V DC 3.0A: >81.39%
9.0V DC 3.0A: >86.62%
12.0V DC 2.25A: >86.62%
Efficiency at low load (10%)| >70.08%| >72.70%| Type A:
5.0V DC 2.4A:
71.00% Type C:
5.0V DC 3.0A:
72.48%
Total:4.2A
74.52%| Type C:
5.0V DC, 3.0A: >72.48%
9.0V DC, 3.0A: >77.30%
12.0V DC, 2.5A: >77.70%
15.0V DC, 2.0A: >77.70%
20.0V DC, 1.5A: >77.70%
Type A:
5.0V DC 3.0A: >72.48%
9.0V DC 3.0A: >77.30%
12.0V DC 2.25A: >77.30%
No load power consumption| <0.10W| <0.10W| <0.10W| <0.10W
USB Port Number| 2 Ports| 2 Ports| 1 Port| 4 Ports, 2.1A per pair| 2 ports| 3 Ports| 2 Ports| 2 Ports (1 type A, 1 type C)| 2 Ports (1 type A, 1 type C)
USB PCBA Model name| X21U2 CH-004BN| X22U CH-003BN X22U CH003C(alt)| CH-Wi-Fi-Power-U| X24U44 CM032| X22U3 CH-008BN
X22U3 CH008C(alt)| X22U33 CH-010BN| EMUSB3X| X22UAC CH012| X22UAC30 CH015
Manufacturers model identifier| x21U2 x21DPU2| x22U| x22UWR| x24U44| x22U3| x22U33| | x22UAC| x22UAC30*
Note| x = range, 3, 4, 8, 9, EBG, Ez, Cz, PCDy, PCy, Nz, Sz, Fz, Lz, Tz, MC5, PM
- = insert colour, ‘W’, ‘B’ or ‘G’;
y = PCD/PC finish ‘WH’,‘CL’,‘BS’,‘PC’,‘BC’,‘PB’, ‘PW’,‘AB’,‘SB’,‘MB’,‘MG’,‘BL’,‘CH’, ‘SL’, ‘BN’, ‘GR’, ‘WD’;
z = Metal finish ‘BS’, ‘PC’, ‘BN’, ‘PR’, ‘PB’, ‘MB’, ‘AB’, ‘BI’, ‘CR‘, ‘PW‘, ‘BC‘, ‘BG‘,‘SL’, ‘SB’.
Technical
Voltage : 220-240V ac
Frequency : 50/60Hz
Rating : 13A
Terminal capacity : 3 x 2.5mm² 3 x 4mm² 2 x 6.0mm²
Min box depth (profiled plates) : 25mm
Min box depth (flat plates) : 35mm or 25mm with spacer provided.
Note – The front surface of this product may become warm in use. This is
normal and not cause for concern.
ASTA Approved
The ASTA quality mark is evidence that the product has been independently
tested to comply with the relevant clauses of the applicable standards.
To maintain the high quality appearance of decorative finish switches and sockets, BG Electrical recommend the use of a soft cloth periodically to clean the front face. When installing a decorative product please ensure that the wall is decorated, finished and free of moisture prior to installation.
BG Electrical recommends avoiding using, but not restricted to, these substances from becoming in contact with the decorative metal front-plates when cleaning or decorating:
- Adhesive tape, including low tack masking tape
- Solvents
- White spirit
- Multi surface cleaners
- Industrial multipurpose cleaning wipes
- Wet wipes
Using items like those listed above may cause a degrading effect to the front- plates lacquer/plated finish, although the function will remain unaffected.
Batch Code explanation
yyWxx Manufacturing date code, year of manufacture (yy) and week of manufacture (Wxx)
Address/Helpline
Luceco PLC
Stafford Park 1
Telford TF3 3BD
ENGLAND
(EU) Luceco SE
C/ Bobinadora 1-5
08302 Mataró
SPAIN
If you have further technical assistance you can get in touch with our
Technical Helpline on:
+44 (0)3300 249 279
technical.support@bgelectrical.co.uk
Environmental Protection
This symbol is known as the “Crossed-out Wheelie Bin Symbol”. When this symbol is marked on a product or battery, it means that it should not be disposed of with your general household waste. Some chemicals contained within electrical/ electronic products or batteries can be harmful to health and the environment. Only dispose of electrical/electronic/ battery items in separate collection schemes, which cater for the recovery and recycling of materials contained within. Your co-operation is vital to ensure the success of these schemes and for the protection of the environment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>