WINONS WFC0007 Hot Wire Foam Cutter User Manual

WINONS WFC0007 Hot Wire Foam Cutter

Specifications

• Model : DINCP9UVT
• Power : 18W
• DC : 9IVN, P1U8TW

Product Information

The Foam Cutter is a versatile tool designed for precise and convenient cuts. It features a temperature adjusting button on the handle, allowing users to adjust the temperature according to their needs. With a variety of accessories and a desktop holder, it is suitable for advertising words making, art model- making, foam-cutting projects, and engraving projects.

Electrical Safety Warnings

• Please check the completeness of the accessories and the condition of the product before use. Contact us immediately if there are any issues.
• It is normal for smoke to be produced during product usage. It is recommended to use the tool in a well-ventilated space or in the open air.
• Avoid touching the heating part when the power is on. Always turn off the tool when not in use.
• If the users are children, adult supervision is required.

Personal Safety Warnings

• Avoid using the tool while tired or under the influence of drugs, alcohol, or medication.
• This tool should not be used by children under 12 years old without adult supervision.
• Wear a protective mask to avoid inhaling harmful smoke during foam cutting. Use an electric fan to draw the fumes away.
• Wear protective gloves to prevent burns from the hot tip. The tip stays hot for several minutes after the tool is turned off.

Application of The Device
This device is designed to apply patterns and designs on a wide variety of foam types.

Product Usage Instructions

1. Plug the AC adaptor into the power socket.
2. Connect the DC plug of the adaptor into the DC port at the end of the product handle.
3. Take the cutting tip and assemble it into the head of the handle.
4. Push the switch on the handle to the mark “-“. The heating needle of the cutting pen will start to heat up.
5. Use the marker pen to draw the desired shape before starting the cutting operation for better results.
6. Slide the temperature button to choose the desired temperature for precise and slow cutting.
7. Wait for the tool to warm up, which takes approximately 5-45 seconds.
8. After cooling down, push the switch on the handle to the mark “o” to turn off the tool.
9. Remove the cutting tip and replace it with another one.
10. Do not remove the cutting tip while the switch is in the mark “-” position.

Tip Care and Cleaning
To maintain optimal performance and make cutting easier, it is important to keep the tip clean. Here are some effective ways to clean the tip:

• Clean the tip with acetone when it is cold.
• Use sandpaper (320 grit) to remove remains of melted foam from the hot-knife. Be careful not to damage the tip.
• Alternatively, you can use steel wool to clean the tip without difficulties.

INSTRUCTIONS

1. Read the manual
2. Wear face mask
3. Wear eye protection
4. Wear protective gloves
5. Caution very hot

Package includes

• Long Cutting Tip
• Power adapter
• Handle
• Black Marker Pen

Features

1. 18 W power
2. Overheat Protection
3. Fast Heat Up

Functional Description

Thanks to the temperature adjusting button on the handle of the Foam Cutter . Users can adjust the temperature according to their need . Variety of accessories and desktop holder make precise and convenient cuts. It allows users to work more easily on advertising words making, art model making and various foam cutting projects and engraving projects.

Electrical Safety Warnings

• Please chek whether the accessories of our products are complete and whether the products are damaged. Any questions, please contact us Immediately.
• It’s a normal phenomenon that producing smoke when you are using this product, please do not worry! Suggest using in a well ventilated Space or work in the open air, if possible.
• Be careful! Do not touch the heating part when is on. Please turn off the tool when not in use.
• If the users are children please use the products under adult supervision.

PERSONAL SAFETY WARNINGS

• Stay alert,do not use the tool while you are tired or under the influence of drugs,alcohol or medication.
• This appliance is not intended to be used by children under 12 years old without adult supervision.
• Use a protective mask. The smoke from foam cutting can be harmful for your health,that’s why always wear a mask while working, a good respirator type with strong protection would be a great choice. Use an electric fan to draw the fumes away from you.
• Wear protective gloves in order to escape burning bare skin.The Tip stays very hot for several minutes after the tool is turned off. To reduce risk of burns, never touch any metal parts of a hot tool.

Application of The Device
This device is created to apply patterns and designs on a wide variety of foam types

1. Expanded polystyrene (EPS)
2. Expanded Polypropylene (EPP)
3. Pearl Cotton
4. Sponge
5. KT board
6. Cellular glass

GENERAL USER INSTRUCTION

• Plug the AC adaptor into the power socket . Connect the DC plug of the adaptor into the DC port at the end of the product handle .
• Take the cutting tip, and assemble it into the head of the handle.
• Please push the switch on the handle to the mark “-”. The heating needle of the cutting pen starts up to heat up, and then it can be used.
• The cutting effect would be better if you use the marker pen to draw the shape before cutting operation.
• You can slide the temperature button to choose the temperature that you need when you need cutting precisely and slowly .
• Warming up takes 5-45 seconds
• Please push the switch on the handle to the mark “o” first, after cooling, remove the cutting tip and change others.
• Please do not remove the cutting tip while the switch on the mark “-”.

Tip and its Use

Long Cutting Tip
Heated up to 380°C in 15, This tip is perfect for creating more detailed design cutting.

HOW TO CARE AND CLEAN TIP

Keeping your foam-cutting tool clean is mandatory If you want to reach a good result and make the process of cutting easier.Here are the most effective ways to clean the tip:

• You can clean the tip with acetone but do it when the tip is cold.
• Sandpaper- It can be used to remove remains of melted foam from the hot-knife. This method is pretty easy and can be done frequently. We recommend using 320 grit paper to avoid damaging the tip.
• Steel Wool- an easy way to clean the tip of your kit without any difficulties.
• Knife Method -another simple method to clean the tip and remove the remains of the foam buildup is using a knife.
• Jeweler’s Rouge- this is not as quick and easy as the other methods,but it’s safer and really effective for tip.
• Polishing Burr – It Is one of the best ways to reach a deep clean result. But This case,you need to be extremely careful in order not to over polish the tip as this may cause thinning overtime.

support@winons.com

FAQ’s

What should I do if the product is damaged or incomplete?

Please contact us immediately to address any issues with the product.

Is it normal for smoke to be produced during usage?

Yes, it is normal for smoke to be produced. We recommend using the tool in a well-ventilated space or in the open air.

Can children use this product?

Children should use this product under adult supervision.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>