tuya JD-S1 Smart Home Doorbell 1080p Door Peephole Camera User Manual

June 15, 2024
Tuya

tuya logo VIDEO DOORBELL
Quick Start Guideline

Before using the product, please read the manual carefully to get started quicklytuya JD S1 Smart Home Doorbell 1080p Door Peephole
Camera

Product Details

tuya JD S1 Smart Home Doorbell 1080p Door Peephole Camera - Product
Details

Installation Diagram

tuya JD S1 Smart Home Doorbell 1080p Door Peephole Camera - Installation
Diagram

Set Up Instructions

  1. Screw and fasten the appropriate screws into the camera unit and pass the FPC cable through the door hole. Then fixing the camera on the door with the double-side tape.tuya JD S1 Smart Home Doorbell 1080p Door Peephole Camera - Set Up Note: Please make sure the arrow on the back is up direction when set up the camera unit.
  2. Remove the cover on the bottom of the hanging board. Connect the FPC cable to the pin slot firmly then put the cover back.tuya JD S1 Smart Home Doorbell 1080p Door Peephole Camera - hanging board
  3. Pass the screw through the hole on the right, and move it to the left to make sure the screw is in the correct position, then fix the hanging board on the door.tuya JD S1 Smart Home Doorbell 1080p Door Peephole Camera - correct position
  4. Put the indoor monitor into the hanging board from top to bottom to make sure it is installed in place. Turn on the power and complete the installation. Note: After completing the installation, please make sure the hanging board and the screen monitor are fastened. Please try to pull the upper part of the monitor to check whether it is loose.

Packaging Included

tuya JD S1 Smart Home Doorbell 1080p Door Peephole Camera - Packaging
Included

Installation Conditions

Peephole Diameter Door Thickness Range Screw Length
12mm-50mm 35mm-65mm 30mm(Short)
65mm-95mm 60mm(Medium)
95mm-120mm 86mm(Long)

Note: please measure the door thickness to select the propriate screws to install the doorbell camera.

APP Download and Registration

  1. Download
    Method①:Download the APP “Tuya Smart” or “Smart Life” in Android or IOS APP store;
    Method②:Download by scanning the following QR code.

|
---|---
https://smartapp.tuya.com/tuyasmart| https://smartapp.tuya.com/smartlife
2. APP Registration & Log in
Register the account in the APP by following the instructions step by step;
Tip: Make sure that the registered email address/phone number is valid so you can retrieve the password by email/verification code if it’s lost.

  1. Add Device
    ① Turn on the device (Switch on), Long press the home button for 5-6 seconds until the screen off and on again (reset the device);tuya JD S1 Smart Home
Doorbell 1080p Door Peephole Camera - Add Device② open Tuya ap—Add Device—Security & Video Surveillance—smart camera (Wi-Fi) ;tuya JD S1 Smart Home Doorbell 1080p Door
Peephole Camera - Security & Video Surveillance③ select 2.4G wifi Network and enter correct wifi password(make sure it is 2.4G WiFi, Not 5G);
    ⑤ the paring QR-code appears in the App;
    ⑥ Scan the QR-code with the doorbell camera (15-20cm) until you hear a voice ” Connection successful” then  next step;tuya JD S1 Smart Home Doorbell 1080p
Door Peephole Camera - correct wifi password⑦After Paring successfully, you can edit the name of the doorbell camera;
    ⑧ Enter the device monitor page for further settings;tuya JD S1 Smart Home
Doorbell 1080p Door Peephole Camera - further settings

Specifications

Indoor Monitor 4.3 Inch LCD Screen
CPU GK7102S
External Storage Support Micro SD(Max to 64G)
Video Recording Support
2-Way Audio APP 2-Way Communication
Camera Resolution 1080P/720P
Battery Capacity 4500mAh
Max PIR Distance 3 Meters
Alarm PIR Motion Detection
PIR Sensor Angle Max to 90°
Wireless Standard IEEE802.11 b/g/n
View Angle 165° Diagonal /130°Horizontal
Charging Type Mirco USB
Dimension Monitor 1359222.5mm, Doorbell Camera ⌀65*19
Temperature and Humidity -15°~60℃
Recommended Charger DC5V2A±10%

Notice

  • Please remember to fully charge the battery with 5V2A charger at least 8-10 hours to activated the total battery capacity before using it.
  • 4500mAh built-in battery and long life, last about 1-2 Months (3-5 times calling per day). It will send APP notification when the battery is insufficient. Please recharge the device in this situation in time.
  • Please put the device in the range where the WiFi signals can be received well.
  • Please note that too thick door might reduce the signals even it is not too far away from the router. We suggest to test the device and wifi signal range before installation.
  • Built with low consumption chip, this device support 3 wake-up methods: App remote wake-up; PIR motion detection wake-up and call button—pressing wake-up. It will go into sleep standby mode within certain time when it is not woken up.
  • NO on-screen menu Interface, recordings and settings are managed in the phone APP. 2-way communication is between the camera unit and the App. There is no microphone with the indoor monitor.

FCC Warnning:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

tuya logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals